Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

creepage pcb distance with "different voltage level" on board

frank bor last edited by

Re: [Clearance](creepage and other safety aspects in "MySensors" PCBs.)

Hi,

We use off line application. I have a doubt about creepage distance. We powered hte circuit (pollution degree 2) with 230Vac+20%=276Vac after the rectifier diode we have 390Vdc. For a double insulation, where I have 276Vac creepage distance is 6.4mm, after the diode (390Vdc) 8mm. that's right or I have to use 8mm everywhere. Thanks.
Reply Quote 0
1 Reply Last reply

1
Posts

142
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50408
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

26
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

42
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

9

0
Votes

9
Posts

61
Views

Great! I'm glad it works and thank you very much for reporting back!
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

20
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }

creepage pcb distance with "different voltage level" on board

Suggested Topics

Over the air updates
General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

Arduino Nano Every problem
Hardware • • hakha4

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

creepage pcb distance with "different voltage level" on board

Suggested Topics

Over the air updates General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design" Hardware • • wrendral

Node with only sendBatteryLevel into Home Assistant Hardware • • Arno

Arduino Nano Every problem Hardware • • hakha4

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Over the air updates
General Discussion • • ToSa

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

Arduino Nano Every problem
Hardware • • hakha4

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts