I have already published all the documentation, on my website, GitHub and openhardware.io
For now I leave the node as finished.
SmartHome: Wireless LED RGBW Controller – 00:55— giltesa
This is a simple, low-cost and quick project that can get a high spouse acceptance factor.
Mirror
Remove the led strip from the aluminum profiles.
Cut the aluminum profiles and the covers to appropriate length. I used a hacksaw to cut profile+cover at the same time to ensure the got the same length.
Cut the led strips at one of the cut points using a side cutter.
Remove the old wires (they are too short to reach the box) and solder new wires.
Put the led strip back inside the aluminum profile. Note that there is a small grove at the back for the strip, this ensures that the strip is close to the profile to maximize cooling.
Glue the profiles to the mirror. I used slow-curing epoxy.
Electronics box
Drill holes in the project box for the switch (6mm) and the potentiometer (6mm should be enough but was too tight so I used 8mm).
Drill a 4mm hole for the wires to the led strips.
Upload the sketch to the Arduino
Connect the Arduino and the battery packs and put them inside the project box.
Fasten the project box using double-sided tape.
Big thanks to my wife for letting me use the action photo.
The choice of MOSFET can be tricky. Seems that irlz44n was discontinued so you may need to find one adapted to the voltage and current you want to handle.
In all the cases you need to get a logic MOSFET too, meaning that they are fully open usually around 1 to 3V.
Also I'm sort of confused as it seems to me that L7812CV is a Voltage regulator, not a MOSFET. So if you are actually using that in the MOSFET spot it will definitively not work.
Especially if you are handling high current or voltage I would recommend using one from a reputable source for your MOSFET, I recently switched from mouser / digikey / aliexpress to mostly use http://www.arrow.com as you get free regular shipping, event if you order a couple of components (no affiliation to them whatsoever).
@mfalkvidd said:
I am using them at 12V so the power would be ~4W. Not too much but still enough to get the sink hot!
The voltage makes no difference. 5A is still 5A.
you are right brain fart
@krisztian
Hi krisztian,
the singleLED board - as its name suggests - features only one LED output. If you want to have a setup with multiple LED strips you need to design a board with multiple outputs. I have already designed a board with 4 outputs, but I haven't built it.
In terms of software you need to register multiple sensors in your program like this:
#define numCh 4 //the number of outputs
const byte ledPins[] = {9,6,5,3};
byte ledLevel[numCh];
boolean ledDimWay[numCh];
//in the setup function request the dim levels from the gateway
for(byte i=0; i<numCh; i++) request(i, V_DIMMER);
//in the presentation function register multiple lights
for(byte i=0; i<numCh; i++) present(i, S_DIMMER);
//if you receive a signal, you need to check for the sensor id
setLED(message.sensor, requestedLevel);
//to set the LED level (function: setLED) you need to use the sensor id to determine brightness and pin
//Fade LED to set level
int delta = (level - ledLevel[child]) < 0 ? -1 : 1;
//Write to LED
analogWrite(ledPins[child], map(ledLevel[child],0,100,0,255));
I will probably publish the whole code once I have built and tested the 4LED controller (i call it "MySensors rainbowLED")
Hope I could help you
ThetaDev
@samuel235
I'm using genuine atmel programmers (currently I'm on jtagice3) been serving me fine for the last couple of years (also have the added benefits of being able to work together with gdb, so I can debug arduino code on my atmel sam D21 mcu)
Anyways, there are lot's of (cheaper) programmers out there, amongst others you could use another arduino as programmer..