Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

GPIO 7 and 8 go high when gateway start on raspberry pi

msmmbl last edited by

I am using raspberry pi 3 as gateway. I found if start mysgw, GPIO 7 and 8 will be in High output state. GPIO 8 is connected to NF24 CS PIN and I have a led on GPIO 7 and I don‘t want the led light all the time. Please help how to make GPIO 7 as GPIO and be to be controlled by mysgw.
Reply Quote 0
1 Reply Last reply

1
Posts

11
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Raspberry pi gateway problem after change of Pi
General Discussion • • Vasilis Vlachoudis

2

0
Votes

2
Posts

10
Views

After re-installing the previous 32bit raspbian version, the gateway seems to work ok. It seems to me there is a problem with the 64bit version.
Most reliable "best" radio
General Discussion • • NeverDie

274

1
Votes

274
Posts

918
Views

It has been a long time but I’ve learned a few things that I wanted to share. This library of information (Thank you NeverDie and others) has been so helpful in my hobby developments. Software Defined Radios for signal analysis. With the help of Andreas Spiess explanation of IQ transformations, I learned about Software Defined Radios and I bought one (RTL-SDR). Using this I can clearly discriminate between effective 433 MHz transmitters and bad ones. Not only is the signal density displayed on the software (SDR#) but so is the frequency. Power Profiler Kit II has been indispensable in watching power usage and seeing into the details of the radio transmission. In effect this thing has saved me from buying an oscilloscope for my simple little bench. Tonight, I saw this video: https://www.youtube.com/watch?v=Z9nycymUd-I It describes common PCB errors. It is too advanced for me, but I did pick-up a few ideas about ground planes (tip #6 from the video). I hope this is of some value for folks.
NewbiePCB sensors dying of old age
General Discussion • • Matt

5

2
Votes

5
Posts

52
Views

Some humidity sensors are known to lose accuracy with age. For instance, the Si7021 is known to have this problem. If that matters to you, then the best choice is to pick sensors that have datasheets and which have specs as to their expected longevity or accuracy over time. Then buy from mouser/digikey to be certain you're getting the real thing rather than factory rejects or counterfeits. For extra insurance, I avoid electrolytic capacitors entirely whenever possible. I buy only 7XR rated ceramic capacitors that are overspec'd. The difference in price is small compared to a failure down the road.
Gateway on Raspberry pi 1
General Discussion • • mimaret

9

0
Votes

9
Posts

40
Views

@mimaret It was a pleasure. Thank you for your feedback!
CNC PCB milling
General Discussion • • sundberg84

933

1
Votes

933
Posts

133978
Views

Of possible interest: Here's a guy who is building an inexpensive open source ethernet controller for stepper motors: What happend to Ethersweep? Project Update! – 12:36— Neumi If you listen to the end, it's revealed that there is now generous funding available which allows people to do this kind of open-source development as a full time job, which is what he is now doing. For that reason, I think there's a good chance he will complete his project within the allowed 6 months., and so by the deadline it will likely be nicely polished.

GPIO 7 and 8 go high when gateway start on raspberry pi

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

Raspberry pi gateway problem after change of Pi
General Discussion • • Vasilis Vlachoudis

Most reliable "best" radio
General Discussion • • NeverDie

NewbiePCB sensors dying of old age
General Discussion • • Matt

Gateway on Raspberry pi 1
General Discussion • • mimaret

CNC PCB milling
General Discussion • • sundberg84

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

GPIO 7 and 8 go high when gateway start on raspberry pi

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

Raspberry pi gateway problem after change of Pi General Discussion • • Vasilis Vlachoudis

Most reliable "best" radio General Discussion • • NeverDie

NewbiePCB sensors dying of old age General Discussion • • Matt

Gateway on Raspberry pi 1 General Discussion • • mimaret

CNC PCB milling General Discussion • • sundberg84

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Update RF24 library to latest version
Bug Reports • • andriej

Raspberry pi gateway problem after change of Pi
General Discussion • • Vasilis Vlachoudis

Most reliable "best" radio
General Discussion • • NeverDie

NewbiePCB sensors dying of old age
General Discussion • • Matt

Gateway on Raspberry pi 1
General Discussion • • mimaret

CNC PCB milling
General Discussion • • sundberg84

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts