[SOLVED] Error compiling ESP8266 Gateway sketch



  • I am attempting to setup an esp8266 gateway but getting errors in compilation, using the sketch below (arduino ide 1.8.9 and http://arduino.esp8266.com/stable/package_esp8266com_index.json in board manager, with mysensors 2.3.2 library)

    Error:

    d/root/Arduino/libraries/MySensors/hal/architecture/ESP8266/MyMainESP8266.cpp: At global scope:
    /root/Arduino/libraries/MySensors/hal/architecture/ESP8266/MyMainESP8266.cpp:140:27: error: expected initializer before 'ets_intr_lock'
     extern "C" void IRAM_ATTR ets_intr_lock()
                               ^
    Using library MySensors at version 2.3.2 in folder: /root/Arduino/libraries/MySensors 
    Using library SPI at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/SPI 
    Using library ESP8266WiFi at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/ESP8266WiFi 
    Using library EEPROM at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/EEPROM 
    exit status 1
    Error compiling for board NodeMCU 1.0 (ESP-12E Module).```
    
    
    
    /*
     * The MySensors Arduino library handles the wireless radio link and protocol
     * between your home built sensors/actuators and HA controller of choice.
     * The sensors forms a self healing radio network with optional repeaters. Each
     * repeater and gateway builds a routing tables in EEPROM which keeps track of the
     * network topology allowing messages to be routed to nodes.
     *
     * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
     * Copyright (C) 2013-2019 Sensnology AB
     * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
     *
     * Documentation: http://www.mysensors.org
     * Support Forum: http://forum.mysensors.org
     *
     * This program is free software; you can redistribute it and/or
     * modify it under the terms of the GNU General Public License
     * version 2 as published by the Free Software Foundation.
     *
     *******************************
     *
     * REVISION HISTORY
     * Version 1.0 - Henrik Ekblad
     * Contribution by a-lurker and Anticimex,
     * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
     * Contribution by Ivo Pullens (ESP8266 support)
     *
     * DESCRIPTION
     * The EthernetGateway sends data received from sensors to the WiFi link.
     * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
     *
     * VERA CONFIGURATION:
     * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
     * E.g. If you want to use the default values in this sketch enter: 192.168.178.66:5003
     *
     * LED purposes:
     * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used.
     * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
     * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
     * - ERR (red) - fast blink on error during transmission error or receive crc error
     *
     * See https://www.mysensors.org/build/connect_radio for wiring instructions.
     *
     * If you are using a "barebone" ESP8266, see
     * https://www.mysensors.org/build/esp8266_gateway#wiring-for-barebone-esp8266
     *
     * Inclusion mode button:
     * - Connect GPIO5 (=D1) via switch to GND ('inclusion switch')
     *
     * Hardware SHA204 signing is currently not supported!
     *
     * Make sure to fill in your ssid and WiFi password below for ssid & pass.
     */
    
    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
    #define MY_BAUD_RATE 9600
    
    // Enables and select radio type (if attached)
    #define MY_RADIO_RF24
    //#define MY_RADIO_RFM69
    //#define MY_RADIO_RFM95
    
    #define MY_GATEWAY_ESP8266
    
    #define MY_WIFI_SSID "MySSID"
    #define MY_WIFI_PASSWORD "MyVerySecretPassword"
    
    // Enable UDP communication
    //#define MY_USE_UDP  // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below
    
    // Set the hostname for the WiFi Client. This is the hostname
    // it will pass to the DHCP server if not static.
    #define MY_HOSTNAME "ESP8266_GW"
    
    // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
    //#define MY_IP_ADDRESS 192,168,178,87
    
    // If using static ip you can define Gateway and Subnet address as well
    //#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
    //#define MY_IP_SUBNET_ADDRESS 255,255,255,0
    
    // The port to keep open on node server mode
    #define MY_PORT 5003
    
    // How many clients should be able to connect to this gateway (default 1)
    #define MY_GATEWAY_MAX_CLIENTS 2
    
    // Controller ip address. Enables client mode (default is "server" mode).
    // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
    //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
    //#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"
    
    // Enable inclusion mode
    //#define MY_INCLUSION_MODE_FEATURE
    
    // Enable Inclusion mode button on gateway
    //#define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
    //#define MY_INCLUSION_MODE_DURATION 60
    // Digital pin used for inclusion mode button
    //#define MY_INCLUSION_MODE_BUTTON_PIN D1
    
    // Set blinking period
    //#define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Flash leds on rx/tx/err
    // Led pins used if blinking feature is enabled above
    //#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
    //#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
    //#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
    
    #include <MySensors.h>
    
    void setup()
    {
      // Setup locally attached sensors
    }
    
    void presentation()
    {
      // Present locally attached sensors here
    }
    
    void loop()
    {
      // Send locally attached sensors data here
    }
    
    

  • Mod

    @mrhutchinsonmn you seem to be using an old esp arduino core. Could you update that to the latest version and try again?



  • Yes, that was it. Thought it was handled under preferences with the url.
    Thank you!


  • Mod

    @mrhutchinsonmn no prob! Glad I could help.


Log in to reply
 

Suggested Topics

  • 4
  • 2
  • 1
  • 14
  • 2
  • 933

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts