Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

DIY LED lens

APL2017 last edited by
For my battery powered water leak nodes I wanted to add a clear lens to be able to see communication LED status on Arduino Pro Mini while maintaining reasonable water protection. The quick no cost solution was:
1. Drill small hole in node enclosure against LED location
2. Cover it from outside with masking tape
3. Put some amount of hot glue from the inside to cover the hole, wait till glue hardens, remove masking tape. And voila!!
Reply Quote 2
1 Reply Last reply

led lens 1

1
Posts

32
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

33
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
Wall mounted 'mood light' v2
My Project • • AWI

29

9
Votes

29
Posts

13182
Views

@adds666 I'm not sure but I believe Domoticz prresents it's dimmer values in steps from 5 to 100 I believe. It'd about 10 steps. That's why I'm not sure if you can add more patterns. Unless you indeed change it to a percentage. Hope it helps
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73895
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Balcony flower box irrigation
My Project • • pbw

2

0
Votes

2
Posts

20
Views

@pbw a gateway's function is to act as a gateway between the nodes and a controller. I don't think you will have all of the needed memory available to add logic to the gateway and you will make your solution very static. You can implemented your own lightway controller, just have a look at the Serial API. But controllers like Domoticz are lightweight and the already over a browser based interface. And most of them are easy to setup creating a much more versatile and dynamic solution.
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8021
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.

DIY LED lens

Suggested Topics

Welcome
Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Wall mounted 'mood light' v2
My Project • • AWI

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Balcony flower box irrigation
My Project • • pbw

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

30
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

DIY LED lens

Suggested Topics

Welcome Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement) My Project • • Kokosnoot

Wall mounted 'mood light' v2 My Project • • AWI

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Balcony flower box irrigation My Project • • pbw

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

30Online

11.2kUsers

11.1kTopics

112.5kPosts

Welcome
Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

Wall mounted 'mood light' v2
My Project • • AWI

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Balcony flower box irrigation
My Project • • pbw

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

30
Online

11.2k
Users

11.1k
Topics

112.5k
Posts