Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Enclosures for SR04, Sparkfun soil moisture and solar panel

Green BMS last edited by

I share the thinkercad 3d projects of the following sensors:
SR04 Ultrasonic sensor: https://www.tinkercad.com/things/69JTPE9g84N

Sparkfun Soil Moisture: https://www.tinkercad.com/things/9VoWTwszHit

Solar Panel 6V 3,5W 135x165 : https://www.tinkercad.com/things/baTjBssvbcp
Reply Quote 0
1 Reply Last reply

1
Posts

9
Views

Suggested Topics

Pass reset on forum
General Discussion • • Dvbit

2

0
Votes

2
Posts

956
Views

I believe Henrik fixed this issue today; see - http://forum.mysensors.org/topic/39/forum-registration-confirmation-url-points-to-localhost#226
Enclosure/Bumper for Easy/Newbie PCB
Enclosures / 3D Printing • • barduino

23

2
Votes

23
Posts

21472
Views

@evb my bad. The nodebb admin interface has a "Save" button that I didn't see so the changes I made were thrown away. I've re-entered the settings ans this time I clicked Save
a truly great build plate
Enclosures / 3D Printing • • NeverDie

1

0
Votes

1
Posts

41
Views

No one has replied
Please help with rspro itx 3d printer
Enclosures / 3D Printing • • malachite666

3

0
Votes

3
Posts

34
Views

To fix, first clean the nozzle to look like new from the outside. Next heat up the nozzle to temp and apply pressure to the filament with your fingers, usually this will push through a clog. If you cannot manually push filament through, consider replacing the nozzle or entire hotend.
New enclosures
Enclosures / 3D Printing • • AlexNO

7

0
Votes

7
Posts

482
Views

Very nice! I knew it would only be a matter of time until we saw MySensors custom injected molded components! I think if you made a box that could fit the Easy / Newbie board (~50x50cm) plus radio and 2AA batteries, you would probably sell a lot of them! I know I would buy some of those...
Best 3d printers
Enclosures / 3D Printing • • Crumpy10

106

0
Votes

106
Posts

4810
Views

Reporting back: I have my BambuLab X1C printer setup and have printed with it for about a week. It's fantastic: it's fast, and the prints come out perfectly every time. Truly an appliance: it works with only minor setup straight out of the box. I'd say it's a quantum leap better than my Prusa MK3S, which I guess I should try to sell while it still has value.

Enclosures for SR04, Sparkfun soil moisture and solar panel

Suggested Topics

Pass reset on forum
General Discussion • • Dvbit

Enclosure/Bumper for Easy/Newbie PCB
Enclosures / 3D Printing • • barduino

a truly great build plate
Enclosures / 3D Printing • • NeverDie

Please help with rspro itx 3d printer
Enclosures / 3D Printing • • malachite666

New enclosures
Enclosures / 3D Printing • • AlexNO

Best 3d printers
Enclosures / 3D Printing • • Crumpy10

28
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

Enclosures for SR04, Sparkfun soil moisture and solar panel

Suggested Topics

Pass reset on forum General Discussion • • Dvbit

Enclosure/Bumper for Easy/Newbie PCB Enclosures / 3D Printing • • barduino

a truly great build plate Enclosures / 3D Printing • • NeverDie

Please help with rspro itx 3d printer Enclosures / 3D Printing • • malachite666

New enclosures Enclosures / 3D Printing • • AlexNO

Best 3d printers Enclosures / 3D Printing • • Crumpy10

28Online

11.2kUsers

11.1kTopics

112.5kPosts

Pass reset on forum
General Discussion • • Dvbit

Enclosure/Bumper for Easy/Newbie PCB
Enclosures / 3D Printing • • barduino

a truly great build plate
Enclosures / 3D Printing • • NeverDie

Please help with rspro itx 3d printer
Enclosures / 3D Printing • • malachite666

New enclosures
Enclosures / 3D Printing • • AlexNO

Best 3d printers
Enclosures / 3D Printing • • Crumpy10

28
Online

11.2k
Users

11.1k
Topics

112.5k
Posts