Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

NodeMCU Gateway not working on Domoticz

obel38 last edited by

Hi,

i have domoticz running bright with Serial Gateway,
i tried to extand my sensor array, so i added a ESP8266 NodeMCU Gateway.

Domoticz config is "MySensors Gateway with LAN interface", with Fixed IP and Port 5003.

Thru Putty i can see sensors datas and presentations received by ESP8266 gateway, but nothing appear in Domoticz,

i have also tried with Ethernet Gateway, same issue.

Please let me know if you see something wrong ???!!!

Thanks for help

regards

Olivier
Reply Quote 0
1 Reply Last reply

1
Posts

681
Views

Suggested Topics

Day 1 - Status report
Announcements • • hek

3

0
Votes

3
Posts

1511
Views

Feels much faster from here too!
RS485 to custom PCB - comms working, relay not clicking - need helps
Troubleshooting • • adds666

3

0
Votes

3
Posts

22
Views

Hi OSD, thanks for your input. Those are the 4 relays on IO-MCU. I buzzed out the circuit and found that I had an open circuit on the 12v line to the relays. Furthermore 2 of the relays indicator LEDs were illuminating, 2 were not. I suspect, when I first juiced up the circuit on this MCU, the 2 relays fired, but I'd made the trace too thin for the required current. I wired up some jumper wire on the reverse of the PCB and the 2 relays started working. The 2 that remain inoperable? https://forum.arduino.cc/t/using-pins-a6-a7-on-pro-mini-compatible/118050 A6 and A7 can only be analogue inputs, cannot be digitally written to..... - so this part of my PCB is now redundant. However, all in all, some good fault finding, found the two issues, and I'm now going away to re-think my PCB trace widths and reading the datasheets more accurately Thanks
Gateway stops communicating (again)
Troubleshooting • • OldSurferDude

2

0
Votes

2
Posts

13
Views

Hm, maybe the problem is that your rPI has a short interruption in the WIFI connection, the MQTT TCP connection is interrupted and does not autostart again. Maybe there is something in the logs. Maybe you can find something about reconnects in one of these: journalctl --unit=systemd-networkd journalctl --unit=wpa_supplicant You could try to run wpa_cli in daemon mode to react to disconnects and connects. Create a script like this: #!/bin/bash case "$2" in CONNECTED) <your command to start the gateway>; ;; DISCONNECTED) <your command to stop the gateway>; ;; esac then, start wpa_cli in deamon mode: wpa_cli -a /path/to/your/script #use sudo if your gateway commands need sudo If that helps, you could create a service from this command. Regards, Edi
can't make getStream() work
Troubleshooting • • Mizar03

2

0
Votes

2
Posts

31
Views

@Mizar03 sorry for the late response. getStream() only works for firmware transfers. I'd suggest getString(), this should also work for all types of payloads, as they are normaly ASCII and not binary data.
Node broadcast loop
Troubleshooting • • Oumuamua

2

0
Votes

2
Posts

23
Views

Solved. Issue with power supply. Added a capacidade to power source.
Can not compile on Arduino Nano ESP 32
Troubleshooting • • ctodor

15

0
Votes

15
Posts

74
Views

@ctodor You are very welcome

NodeMCU Gateway not working on Domoticz

Suggested Topics

Day 1 - Status report
Announcements • • hek

RS485 to custom PCB - comms working, relay not clicking - need helps
Troubleshooting • • adds666

Gateway stops communicating (again)
Troubleshooting • • OldSurferDude

can't make getStream() work
Troubleshooting • • Mizar03

Node broadcast loop
Troubleshooting • • Oumuamua

Can not compile on Arduino Nano ESP 32
Troubleshooting • • ctodor

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

NodeMCU Gateway not working on Domoticz

Suggested Topics

Day 1 - Status report Announcements • • hek

RS485 to custom PCB - comms working, relay not clicking - need helps Troubleshooting • • adds666

Gateway stops communicating (again) Troubleshooting • • OldSurferDude

can't make getStream() work Troubleshooting • • Mizar03

Node broadcast loop Troubleshooting • • Oumuamua

Can not compile on Arduino Nano ESP 32 Troubleshooting • • ctodor

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Day 1 - Status report
Announcements • • hek

RS485 to custom PCB - comms working, relay not clicking - need helps
Troubleshooting • • adds666

Gateway stops communicating (again)
Troubleshooting • • OldSurferDude

can't make getStream() work
Troubleshooting • • Mizar03

Node broadcast loop
Troubleshooting • • Oumuamua

Can not compile on Arduino Nano ESP 32
Troubleshooting • • ctodor

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts