Arduino Uno R3 Ethernet Gateway + 4 Relay + Motion + Magnetic Switch



  • Hello ,

    I'm trying to build the gateway with all attached sensors

    But when I inclusion, only appears the 4 relays in Vera , what is wrong with the code?

    not appear --> motion and Magnetic Switch

    Setup:
    Arduino Uno R3
    W5100 Shield
    4 Relay - pin 5,6,7,8
    1 motion - pin 3
    1 magnetic switch - pin 4

    // Enable debug prints to serial monitor
    #define MY_DEBUG 
    
    // Enable gateway ethernet module type 
    #define MY_GATEWAY_W5100
    
    #define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
    
    // The port to keep open on node server mode / or port to contact in client mode
    #define MY_PORT 5003        
     
    // The MAC address can be anything you want but should be unique on your network.
    // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
    // Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
     #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
    
    // Enable inclusion mode
     #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    // #define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
     #define MY_INCLUSION_MODE_DURATION 60 
    // Digital pin used for inclusion mode button
    // #define MY_INCLUSION_MODE_BUTTON_PIN  4 
    
    #include <SPI.h>
    #include <Ethernet.h>
    #include <MySensor.h>
    #include <Bounce2.h>
    
    #define RELAY_1  5  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
    #define NUMBER_OF_RELAYS 4 // Total number of attached relays
    #define RELAY_ON 1  // GPIO value to write to turn on attached relay
    #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
    #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
    #define CHILD_ID 3   // Id of the sensor child
    #define ID 4
    
    #define OPEN 1
    #define CLOSE 0
    #define BUTTON_PIN  4  // Arduino Digital I/O pin for button/reed switc
    
    boolean lastTripped = 0;
    Bounce debouncer = Bounce(); 
    int oldValue=-1;
    
    // Initialize motion message
    MyMessage msg(CHILD_ID, V_TRIPPED);
    MyMessage msgdoor(ID,V_TRIPPED);
    
    
    void before() { 
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Then set relay pins in output mode
        pinMode(pin, OUTPUT);   
        // Set relay to last known state (using eeprom storage) 
        digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
      }
    }
    
    void setup() {
      pinMode(BUTTON_PIN,INPUT_PULLUP);
      debouncer.attach(BUTTON_PIN);
      debouncer.interval(5);
      present(ID, S_LIGHT); // S_DOOR
      
    }
    
    void presentation()  
    {   
      // Send the sketch version information to the gateway and Controller
      sendSketchInfo("Relay", "1.0");
    
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_LIGHT);
      }
         pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
      // Register all sensors to gw (they will be created as child devices)
      present(CHILD_ID, S_MOTION);
    }
    
    
    void loop() 
    {
        // Read digital motion value
      boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
    
        if (lastTripped != tripped ) {
          send(msg.set(tripped?"1":"0")); // Send new state and request ack back
          Serial.println(tripped);
          lastTripped=tripped; 
    }
    debouncer.update();
      int value = debouncer.read();
      if (value != oldValue) {
         Serial.print("Door value: ");
         Serial.println(value);
         send(msgdoor.set(value==HIGH ? 1 : 0));
         oldValue = value;
    
      }
    }
    
    void receive(const MyMessage &message) {
      // We only expect one type of message from controller. But we better check anyway.
      if (message.type==V_LIGHT) {
         // Change relay state
         digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
         // Store state in eeprom
         saveState(message.sensor, message.getBool());
         // Write some debug info
         Serial.print("Incoming change for sensor:");
         Serial.print(message.sensor);
         Serial.print(", New status: ");
         Serial.println(message.getBool());
       } 
    }```

  • Admin

    Your child ids are overlapping.



  • @hek tks, motion sensor now appear but magnetic switch no 😞 need resistor ?

    Update code

    
    // Enable debug prints to serial monitor
    #define MY_DEBUG 
    
    // Enable gateway ethernet module type 
    #define MY_GATEWAY_W5100
    
    #define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
    
    // The port to keep open on node server mode / or port to contact in client mode
    #define MY_PORT 5003        
     
    // The MAC address can be anything you want but should be unique on your network.
    // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
    // Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
     #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
    
    // Enable inclusion mode
     #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    // #define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
     #define MY_INCLUSION_MODE_DURATION 60 
    // Digital pin used for inclusion mode button
    // #define MY_INCLUSION_MODE_BUTTON_PIN  4 
    
    #include <SPI.h>
    #include <Ethernet.h>
    #include <MySensor.h>
    #include <Bounce2.h>
    
    #define RELAY_1  5  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
    #define NUMBER_OF_RELAYS 4 // Total number of attached relays
    #define RELAY_ON 1  // GPIO value to write to turn on attached relay
    #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
    #define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
    #define CHILD_ID 69   // Id of the sensor child
    #define ID 70
    #define OPEN 1
    #define CLOSE 0
    #define BUTTON_PIN  4  // Arduino Digital I/O pin for button/reed switc
    
    boolean lastTripped = 0;
    Bounce debouncer = Bounce(); 
    int oldValue=-1;
    
    // Initialize motion message
    MyMessage msg(CHILD_ID, V_TRIPPED);
    MyMessage msgdoor(ID,V_TRIPPED);
    
    
    void before() { 
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Then set relay pins in output mode
        pinMode(pin, OUTPUT);   
        // Set relay to last known state (using eeprom storage) 
        digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
      }
    }
    
    void setup() {
      pinMode(BUTTON_PIN,INPUT_PULLUP);
      debouncer.attach(BUTTON_PIN);
      debouncer.interval(5);
      present(ID, S_DOOR); // S_DOOR
      
    }
    
    void presentation()  
    {   
      // Send the sketch version information to the gateway and Controller
      sendSketchInfo("Relay", "1.0");
    
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_LIGHT);
      }
         pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
      // Register all sensors to gw (they will be created as child devices)
      present(CHILD_ID, S_MOTION);
    }
    
    
    void loop() 
    {
        // Read digital motion value
      boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
    
        if (lastTripped != tripped ) {
          send(msg.set(tripped?"1":"0")); // Send new state and request ack back
          Serial.println(tripped);
          lastTripped=tripped; 
    }
    debouncer.update();
      int value = debouncer.read();
      if (value != oldValue) {
         Serial.print("Door value: ");
         Serial.println(value);
         send(msgdoor.set(value==HIGH ? 1 : 0));
         oldValue = value;
    
      }
    }
    
    void receive(const MyMessage &message) {
      // We only expect one type of message from controller. But we better check anyway.
      if (message.type==V_LIGHT) {
         // Change relay state
         digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
         // Store state in eeprom
         saveState(message.sensor, message.getBool());
         // Write some debug info
         Serial.print("Incoming change for sensor:");
         Serial.print(message.sensor);
         Serial.print(", New status: ");
         Serial.println(message.getBool());
       } 
    }```


  • Any ideia plz?


  • Admin

    If the presentation fails to be received by the controller, you could introduce a small delay (to let radio "re-change") between the transmits to the controller.

    wait(200); at the top of the loop should be enough.



  • @hek

    Still not working 😕

    void loop() 
    {  
       wait(200);
        // Read digital motion value
      boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
    
        if (lastTripped != tripped ) {
          send(msg.set(tripped?"1":"0")); // Send new state and request ack back
          Serial.println(tripped);
          lastTripped=tripped; 
    }
    debouncer.update();
      int value = debouncer.read();
      if (value != oldValue) {
         Serial.print("Door value: ");
         Serial.println(value);
         send(msgdoor.set(value==HIGH ? 1 : 0));
         oldValue = value;
    
      }
    }
    

  • Admin

    When doing the presentation...



  • @hek

    Working!!!! Tks

    I only have one more problem, with simple button switch ( like that ) simulate door open/close , I receive message "Door value:0 and 1" and status in vera changed, but with reed switch ( like that ) door status no change with magnetic , I bought 5 reed switch and any works 😞

    Reed switch problem right ?


  • Hero Member

    @mlg Probably the reed switch. It is just a mechanical device. You can try with an ohm meter (or with battery and light/ led)



  • Update

    Finally after changing reed switch all works !

    However , sometimes mysensors gateway stop responding (few weeks works fine), I try to ping Ip of the gateway and no have any reply, solution is power off gateway .

    It is possible to place the gateway (mysensors) to ping a network address and if it does not answer automatically make a restart and wait/limit to a restart every 20 minutes? (to prevent the restart loop)


Log in to reply
 

Suggested Topics

  • 2
  • 6
  • 10
  • 1
  • 1

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts