Arduino with ESP8266-01 and MQTT



  • Works MQTT Gateway library with ESP8266-01?
    I uploaded MQTT Gateway library to my ESP8266-01 and I dont know what I have upload to my Arduino. Im testing SerialGateway sketch with RelayActuator sketch like this.
    RX and TX from ESP8266 to pin 8,9.

    // Enable debug prints to serial monitor
    #define MY_DEBUG 
    
    // Enable RS485 transport layer
    #define MY_RS485
    
    // Define this to enables DE-pin management on defined pin 
    #define MY_RS485_DE_PIN 2
    
    // Set RS485 baud rate to use
    #define MY_RS485_BAUD_RATE 9600
    
    // Enable serial gateway
    #define MY_GATEWAY_SERIAL
    
    // Flash leds on rx/tx/err
    #define MY_LEDS_BLINKING_FEATURE
    // Set blinking period
    #define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Enable inclusion mode
    #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    #define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
    #define MY_INCLUSION_MODE_DURATION 60 
    // Digital pin used for inclusion mode button
    #define MY_INCLUSION_MODE_BUTTON_PIN  3 
    
    #define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
    #define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
    #define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED
    
    #include <SPI.h>
    #include <MySensors.h>  
    
    #define RELAY_1  11  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
    #define NUMBER_OF_RELAYS 2 // Total number of attached relays
    #define RELAY_ON 1  // GPIO value to write to turn on attached relay
    #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
    
    
    void before() { 
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Then set relay pins in output mode
        pinMode(pin, OUTPUT);   
        // Set relay to last known state (using eeprom storage) 
        digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
      }
    }
    
    void setup() { 
      // Setup locally attached sensors
    }
    
    void presentation()  
    {   
      // Send the sketch version information to the gateway and Controller
      sendSketchInfo("Relay", "1.0");
    
      for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
        // Register all sensors to gw (they will be created as child devices)
        present(sensor, S_LIGHT);
      }
    }
    
    
    void loop() 
    {
      
    }
    
    void receive(const MyMessage &message) {
      // We only expect one type of message from controller. But we better check anyway.
      if (message.type==V_LIGHT) {
         // Change relay state
         digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
         // Store state in eeprom
         saveState(message.sensor, message.getBool());
         // Write some debug info
         Serial.print("Incoming change for sensor:");
         Serial.print(message.sensor);
         Serial.print(", New status: ");
         Serial.println(message.getBool());
       } 
    }
    

    My serial monitor output:

    0;255;3;0;9;TSP:SANCHK:OK
    0;255;3;0;9;Starting gateway (RSNGA-, 2.0.0)
    0;255;3;0;9;TSM:INIT
    0;255;3;0;9;TSM:RADIO:OK
    0;255;3;0;9;TSM:GW MODE
    0;255;3;0;9;TSM:READY
    0;255;3;0;14;Gateway startup complete.
    0;255;0;0;18;2.0.0
    0;255;3;0;11;Relay
    0;255;3;0;12;1.0
    0;1;0;0;3;
    0;2;0;0;3;
    0;255;3;0;9;No registration required
    0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
    

Log in to reply
 

Suggested Topics

  • 4
  • 9
  • 14
  • 5
  • 2
  • 3

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts