not going in the void receive() function



  • Hi,
    working on my sensors v2, IDE arduino 1.6.7
    The sketch is working OK, and connects to my jeedom controller no problem.
    I want to use the data received from node directly on my gateway to process it (jeedom is just here to record the data over time).

    on my serial gateway sketch, I added a void receive( const Mymessage &message) {} fonction, and it seems the sketch is never going there, even when messages are received, as I can see in my serial console.

    Any idea someone? Any help much appreciated.

    
    // Enable debug prints to serial monitor
    #define MY_DEBUG 
    
    
    // Enable and select radio type attached
    #define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    
    // Set LOW transmit power level as default, if you have an amplified NRF-module and
    // power your radio separately with a good regulator you can turn up PA level. 
    #define MY_RF24_PA_LEVEL RF24_PA_LOW
    
    // Enable serial gateway
    #define MY_GATEWAY_SERIAL
    
    // Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
    #if F_CPU == 8000000L
    #define MY_BAUD_RATE 38400
    #endif
    
    // Flash leds on rx/tx/err
    #define MY_LEDS_BLINKING_FEATURE
    // Set blinking period
    #define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Inverses the behavior of leds
    //#define MY_WITH_LEDS_BLINKING_INVERSE
    
    // Enable inclusion mode
    #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    #define MY_INCLUSION_BUTTON_FEATURE
    
    // Inverses behavior of inclusion button (if using external pullup)
    //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
    
    // Set inclusion mode duration (in seconds)
    #define MY_INCLUSION_MODE_DURATION 60 
    // Digital pin used for inclusion mode button
    #define MY_INCLUSION_MODE_BUTTON_PIN  3 
    
    // Uncomment to override default HW configurations
    //#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
    //#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
    //#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED
    
    #include <SPI.h>
    #include <MySensors.h>  
    #include <DHT.h>
    
    #define CHILD_ID_HUM 10
    #define CHILD_ID_TEMP 11
    #define HUMIDITY_SENSOR_DIGITAL_PIN 4  //data pin pour DHT
    
    #define BUREAU_NODE_ID 1
    #define GW_NODE_ID 0
    #define DS18B20 0
    #define THERM 17
    #define TEMP_DHT 11
    #define HRD_HT 10
    
    float bureauds = 0, bureautherm =0, tempdht = 0, hrdht =0;
    
    unsigned long SLEEP_TIME = 10000; // Sleep time between reads (in milliseconds)
    
    DHT dht;
    //float lastTemp;
    //float lastHum;
    boolean metric = true; 
    MyMessage msgHum(CHILD_ID_HUM, V_HUM);
    MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
    
    void setup() { 
      // Setup locally attached sensors
      Serial.begin(115200);
      Serial.println();
      Serial.println("Status\tHumidity (%)\tTemperature (C)\t(F)");
    
      dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN); 
    }
    
    void presentation() {
      sendSketchInfo("GW Humidity/Temp", "1.0");
     // Present locally attached sensors 
      present(CHILD_ID_HUM, S_HUM);
      present(CHILD_ID_TEMP, S_TEMP);
    }
    
    void loop() { 
      // Send locally attached sensor data here 
      wait(dht.getMinimumSamplingPeriod());
    
    float temperature = dht.getTemperature();
      if (isnan(temperature)) {
          Serial.println("Failed reading temperature from DHT");
      } else {
        send(msgTemp.set(temperature, 1));
        Serial.print("T: ");
        Serial.println(temperature);
      }
    
      float humidity = dht.getHumidity();
      if (isnan(humidity)) {
          Serial.println("Failed reading humidity from DHT");
      } else {
          send(msgHum.set(humidity, 1));
          Serial.print("H: ");
          Serial.println(humidity);
      }
    
     Serial.print("Dallas: ");
     Serial.println(bureauds);
     Serial.print("Therm: ");
     Serial.println(bureautherm);
     Serial.print("tempDHT: ");
     Serial.println(tempdht);
     Serial.print("HRDHT: ");
     Serial.println(hrdht);
    
      // Sleep until interrupt comes in on motion sensor. Send update every two minute. 
      //sleep(SLEEP_TIME);
      wait(SLEEP_TIME);
        
    }
    
    
    void receive(const MyMessage &message) {
      Serial.print("received something: ");
      Serial.println(message.sender, message.sensor);
      
      switch (message.sender) {
            case BUREAU_NODE_ID:
                 switch (message.sensor){
                       case DS18B20:
                             bureauds = message.getFloat();
                      break; 
                      case THERM:
                             bureautherm = message.getFloat();
                      break;
              } 
              break; 
         case GW_NODE_ID:
                 switch (message.sensor){
                      case TEMP_DHT:
                             tempdht = message.getFloat();
                      break; 
                      case HRD_HT:
                             hrdht = message.getFloat();
                      break; 
            } 
             break; 
      }
     Serial.print("Dallas: ");
     Serial.println(bureauds);
     Serial.print("Therm: ");
     Serial.println(bureautherm);
     Serial.print("tempDHT: ");
     Serial.println(tempdht);
     Serial.print("HRDHT: ");
     Serial.println(hrdht);
       
    }
    
    

    abstract from serial output when a message is received from node 1, with sensors 0 and 17 :
    0;255;3;0;9;TSP:SANCHK:OK
    0;11;1;0;0;25.4
    T: 25.40
    0;10;1;0;1;50.3
    H: 50.30
    Dallas: 0.00
    Therm: 0.00
    tempDHT: 0.00
    HRDHT: 0.00
    0;255;3;0;9;TSP:MSG:READ 1-1-0 s=0,c=1,t=0,pt=7,l=5,sg=0:24.5
    1;0;1;0;0;24.5
    0;255;3;0;9;TSP:MSG:READ 1-1-0 s=17,c=1,t=0,pt=7,l=5,sg=0:24.6
    1;17;1;0;0;24.6
    0;255;3;0;9;TSP:MSG:READ 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:94
    1;255;3;0;0;94
    0;255;3;0;9;TSP:MSG:READ 1-1-0 s=20,c=1,t=38,pt=7,l=5,sg=0:3.8
    1;20;1;0;38;3.8
    0;11;1;0;0;25.3
    T: 25.30
    0;10;1;0;1;50.2
    H: 50.20
    Dallas: 0.00
    Therm: 0.00
    tempDHT: 0.00
    HRDHT: 0.00
    0;11;1;0;0;25.3
    T: 25.30
    0;10;1;0;1;50.2
    H: 50.20
    Dallas: 0.00
    Therm: 0.00
    tempDHT: 0.00
    HRDHT: 0.00

    Thanks, Nicolas


  • Mod

    This post is deleted!

Log in to reply
 

Suggested Topics

  • 3
  • 2
  • 15
  • 10
  • 2
  • 4

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts