Serial Gateway not recognized



  • Hi,

    Domoticz is running on a NanoPi Linux. I just started with Domoticz. The gateway was recognized 2 days ago, but after i accidentally removed the sdcard while running it won't recognize the gateway any more. Made a fresh Domoticz installation. But no entry in the Hardware section 😞

    So my gateway is connected to ttyUSB0 according to dmesg. Correct?

    [  400.935722] ch341 6-1:1.0: device disconnected
    [  406.871835] ehci_irq: highspeed device connect
    [  407.080056] ehci_irq: highspeed device disconnect
    [  407.080087] ohci_irq: fullspeed or lowspeed device connect
    [  407.510120] usb 8-1: new full-speed USB device number 2 using sunxi-ohci
    [  407.731631] ch341 8-1:1.0: ch341-uart converter detected
    [  407.772934] usb 8-1: ch341-uart converter now attached to ttyUSB0
    
    

    This is the only thing that happens after starting Domoticz:

    2016-10-10 20:22:52.046 Domoticz V3.5744 (c)2012-2016 GizMoCuz
    2016-10-10 20:22:52.047 Build Hash: 289b09a, Date: 2016-10-09 15:14:57
    2016-10-10 20:22:52.047 Startup Path: /root/domoticz/
    2016-10-10 20:22:52.133 Sunrise: 07:12:00 SunSet:19:10:00
    2016-10-10 20:22:52.133 EventSystem: reset all events...
    2016-10-10 20:22:52.163 Active notification subsystems: (0/12)
    2016-10-10 20:22:52.195 WebServer(HTTP) started on address: :: with port 8080
    2016-10-10 20:22:52.220 WebServer(SSL) started on address: :: with port 443
    2016-10-10 20:22:52.222 Proxymanager started.
    2016-10-10 20:22:52.225 Starting shared server on: :::6144
    2016-10-10 20:22:52.225 TCPServer: shared server started...
    2016-10-10 20:22:52.226 RxQueue: queue worker started...
    2016-10-10 20:22:54.229 EventSystem: reset all events...
    2016-10-10 20:22:54.230 EventSystem: reset all device statuses...
    2016-10-10 20:22:54.232 EventSystem: Started
    2016-10-10 20:22:54.950 Incoming connection from: 192.168.1.155
    

    So. No gateway found. 😞
    This is my Gateway sketch from Arduini IDE examples:

    
    // Enable debug prints to serial monitor
    #define MY_DEBUG 
    
    
    // Enable and select radio type attached
    #define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    
    // Set LOW transmit power level as default, if you have an amplified NRF-module and
    // power your radio separately with a good regulator you can turn up PA level. 
    #define MY_RF24_PA_LEVEL RF24_PA_LOW
    
    // Enable serial gateway
    #define MY_GATEWAY_SERIAL
    
    // Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
    #if F_CPU == 8000000L
    #define MY_BAUD_RATE 38400
    #endif
    
    // Flash leds on rx/tx/err
    #define MY_LEDS_BLINKING_FEATURE
    // Set blinking period
    #define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Inverses the behavior of leds
    //#define MY_WITH_LEDS_BLINKING_INVERSE
    
    // Enable inclusion mode
    #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    #define MY_INCLUSION_BUTTON_FEATURE
    
    // Inverses behavior of inclusion button (if using external pullup)
    //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
    
    // Set inclusion mode duration (in seconds)
    #define MY_INCLUSION_MODE_DURATION 60 
    // Digital pin used for inclusion mode button
    #define MY_INCLUSION_MODE_BUTTON_PIN  3 
    
    // Uncomment to override default HW configurations
    //#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
    //#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
    //#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED
    
    #include <SPI.h>
    #include <MySensors.h>  
    
    void setup() { 
      // Setup locally attached sensors
    }
    
    void presentation() {
     // Present locally attached sensors 
    }
    
    void loop() { 
      // Send locally attached sensor data here 
    }
    

    When i connect the Gateway to my windows PC the serial monior shows this:

    0;255;3;0;9;Starting gateway (RNNGA-, 2.0.0)
    0;255;3;0;9;TSM:INIT
    0;255;3;0;9;TSM:RADIO:OK
    0;255;3;0;9;TSM:GW MODE
    0;255;3;0;9;TSM:READY
    0;255;3;0;14;Gateway startup complete.
    0;255;0;0;18;2.0.0
    0;255;3;0;9;No registration required
    0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
    

    I don't see what can be wrong. What else can i check or change?

    Cheeers from Sumatra
    ED



  • What are your settings in Domoticz, hardware?



  • I am not sure what you mean by "settings"? Where can i do hardware settings?
    Here is how my Hardware section looks like:
    0_1476105855079_upload-f4fdbfa2-7027-44ab-bf78-172eb678a976



  • Wow.
    Proof of beeing a real noob:

    I thought it will recognize the gateway automatically. But seems i must add it manual.
    Stupid me. Sorry wasting time and space.


  • Mod

    @edsteve no waste at all. Someone else might make the same mistake and now they'll be able to find the solution if they search. Thanks for reporting back 🙂


Log in to reply
 

Suggested Topics

  • 5
  • 2
  • 3
  • 4
  • 1
  • 5

25
Online

11.2k
Users

11.1k
Topics

112.5k
Posts