mysgw: bind: Address already in use



  • Hi there!

    Just started with my diy home automation project and as was following the https://www.mysensors.org/build/raspberry tutorial.

    What I have done so far:

    1. Installed openhab2 on a rpi2
    2. followed all the steps of the guide
    3. wired the NRF24L01+ onto the rpi

    Now, as my sensors haven't arrived yet, I would like to test if I can make the rpi and a adruino mini pro communicate via the radio.

    The problem:

    pi@raspberrypi:~ $ sudo /usr/local/bin/mysgw -d
    mysgw: Starting gateway...
    mysgw: Protocol version - 2.1.1
    mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
    mysgw: TSF:LRT:OK
    mysgw: TSM:INIT
    mysgw: TSF:WUR:MS=0
    mysgw: TSM:INIT:TSP OK
    mysgw: TSM:INIT:GW MODE
    mysgw: TSM:READY:ID=0,PAR=0,DIS=0
    mysgw: MCO:REG:NOT NEEDED
    mysgw: bind: Address already in use
    mysgw: Failed to bind!
    mysgw: MCO:BGN:STP
    mysgw: MCO:BGN:INIT OK,TSP=1
    mysgw: accept: Bad file descriptor
    mysgw: accept: Bad file descriptor
    mysgw: accept: Bad file descriptor
    ...
    mysgw: accept: Bad file descriptor
    mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
    mysgw: !TSF:MSG:LEN,0!=7
    mysgw: accept: Bad file descriptor
    ...
    

    I found what I think is a similar issue here: https://forum.mysensors.org/topic/1598/openhab-2-0-binding/303

    But the process was overwhelming for a a beginner at my level.

    There probably is a step I am missing, but couldn't locate it.

    The problem with all these tutorials is that they tell what to do but don't explain what you are doing and why. If anyone knows any good basic principle "text books" on the subject, please add a link or something.

    Regards,
    Fipster


  • Hero Member

    Looks like another service is already blocking the port for the gateway. My guess: there already is a instance of the gateway running. Check with: "ps -ax" command. You should see all running process.



  • @TimO

    Thank you for quick response!

    There are the running processes:

      PID TTY      STAT   TIME COMMAND
        1 ?        Ss     0:03 /sbin/init splash
        2 ?        S      0:00 [kthreadd]
        3 ?        S      0:01 [ksoftirqd/0]
        5 ?        S<     0:00 [kworker/0:0H]
        7 ?        S      0:15 [rcu_sched]
        8 ?        S      0:00 [rcu_bh]
        9 ?        S      0:00 [migration/0]
       10 ?        S      0:00 [migration/1]
       11 ?        S      0:01 [ksoftirqd/1]
       13 ?        S<     0:00 [kworker/1:0H]
       14 ?        S      0:00 [migration/2]
       15 ?        S      0:01 [ksoftirqd/2]
       17 ?        S<     0:00 [kworker/2:0H]
       18 ?        S      0:00 [migration/3]
       19 ?        S      0:02 [ksoftirqd/3]
       21 ?        S<     0:00 [kworker/3:0H]
       22 ?        S      0:00 [kdevtmpfs]
       23 ?        S<     0:00 [netns]
       24 ?        S<     0:00 [perf]
       25 ?        S      0:00 [khungtaskd]
       26 ?        S<     0:00 [writeback]
       27 ?        S<     0:00 [crypto]
       28 ?        S<     0:00 [bioset]
       29 ?        S<     0:00 [kblockd]
       30 ?        S      0:00 [kworker/0:1]
       31 ?        S<     0:00 [rpciod]
       32 ?        S      0:00 [kswapd0]
       33 ?        S<     0:00 [vmstat]
       34 ?        S      0:00 [fsnotify_mark]
       35 ?        S<     0:00 [nfsiod]
       44 ?        S<     0:00 [kthrotld]
       45 ?        S<     0:00 [bioset]
       46 ?        S<     0:00 [bioset]
       47 ?        S<     0:00 [bioset]
       48 ?        S<     0:00 [bioset]
       49 ?        S<     0:00 [bioset]
       50 ?        S<     0:00 [bioset]
       51 ?        S<     0:00 [bioset]
       52 ?        S<     0:00 [bioset]
       53 ?        S<     0:00 [bioset]
       54 ?        S<     0:00 [bioset]
       55 ?        S<     0:00 [bioset]
       56 ?        S<     0:00 [bioset]
       57 ?        S<     0:00 [bioset]
       58 ?        S<     0:00 [bioset]
       59 ?        S<     0:00 [bioset]
       60 ?        S<     0:00 [bioset]
       61 ?        S<     0:00 [bioset]
       62 ?        S<     0:00 [bioset]
       63 ?        S<     0:00 [bioset]
       64 ?        S<     0:00 [bioset]
       65 ?        S<     0:00 [bioset]
       66 ?        S<     0:00 [bioset]
       67 ?        S<     0:00 [bioset]
       68 ?        S<     0:00 [bioset]
       69 ?        S<     0:00 [VCHIQ-0]
       70 ?        S<     0:00 [VCHIQr-0]
       71 ?        S<     0:00 [VCHIQs-0]
       72 ?        S<     0:00 [iscsi_eh]
       73 ?        S<     0:00 [dwc_otg]
       75 ?        S<     0:00 [DWC Notificatio]
       77 ?        S      0:00 [VCHIQka-0]
       78 ?        S<     0:00 [deferwq]
       80 ?        S<     0:00 [bioset]
       81 ?        S      0:01 [mmcqd/0]
       82 ?        S      0:00 [jbd2/mmcblk0p2-]
       83 ?        S<     0:00 [ext4-rsv-conver]
       87 ?        S<     0:00 [ipv6_addrconf]
      104 ?        S<     0:00 [kworker/0:1H]
      131 ?        Ss     0:06 /lib/systemd/systemd-journald
      135 ?        Ss     0:00 /lib/systemd/systemd-udevd
      283 ?        S      0:00 [kworker/2:2]
      367 ?        Ssl    0:01 /usr/sbin/rsyslogd -n
      368 ?        Ss     0:00 /usr/sbin/cron -f
      370 ?        Ss     0:00 avahi-daemon: running [raspberrypi.local]
      371 ?        Ss     1:51 /usr/local/bin/mysgw
      372 ?        Ss     0:00 /usr/bin/dbus-daemon --system --address=systemd: --nofork --nopidfil
      375 ?        S      0:00 avahi-daemon: chroot helper
      379 ?        S<     0:00 [cfg80211]
      380 ?        Ss     0:00 /sbin/dhcpcd -q -b
      405 ?        Ss     0:00 /lib/systemd/systemd-logind
      414 ?        S<     0:00 [kworker/3:1H]
      430 ?        Ss     0:00 /usr/sbin/sshd -D
      437 ?        Ss     0:00 /bin/bash /usr/share/openhab2/runtime/bin/karaf server
      454 ?        Ssl    0:00 /usr/sbin/lightdm
      596 ?        Ss     0:00 /usr/sbin/thd --daemon --triggers /etc/triggerhappy/triggers.d/ --so
      619 tty7     Ssl+   0:03 /usr/lib/xorg/Xorg :0 -seat seat0 -auth /var/run/lightdm/root/:0 -no
      620 tty1     Ss     0:00 /bin/login -f
      621 ?        Ss     0:00 /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 106:111
      622 ?        Ss+    0:00 /sbin/agetty --keep-baud 115200 38400 9600 ttyAMA0 vt102
      629 ?        S<     0:00 [kworker/2:1H]
      633 ?        Ss     0:00 /lib/systemd/systemd --user
      638 ?        S      0:00 (sd-pam)
      646 tty1     S+     0:00 -bash
      703 ?        Sl     0:00 lightdm --session-child 13 16
      723 ?        Ssl    0:00 /usr/bin/lxsession -s LXDE-pi -e LXDE
      782 ?        Sl     1:53 /usr/bin/java -Dopenhab.home=/usr/share/openhab2 -Dopenhab.conf=/etc
      804 ?        Ss     0:00 /usr/bin/ssh-agent /usr/bin/dbus-launch --exit-with-session x-sessio
      807 ?        S      0:00 /usr/bin/dbus-launch --exit-with-session x-session-manager
      808 ?        Ss     0:00 /usr/bin/dbus-daemon --fork --print-pid 5 --print-address 7 --sessio
      818 ?        Sl     0:00 /usr/lib/gvfs/gvfsd
      822 ?        Sl     0:00 /usr/lib/gvfs/gvfsd-fuse /run/user/1000/gvfs -f -o big_writes
      823 ?        S<     0:00 [kworker/1:1H]
      997 ?        S      0:01 openbox --config-file /home/pi/.config/openbox/lxde-pi-rc.xml
      999 ?        Sl     0:00 lxpolkit
     1003 ?        Sl     0:01 pcmanfm --desktop --profile LXDE-pi
     1009 ?        Ss     0:00 /usr/bin/ssh-agent -s
     1018 ?        Ssl    0:00 /usr/lib/policykit-1/polkitd --no-debug
     1023 ?        S      0:00 sh -c zenity --info --text="Your Raspbian system has been upgraded t
     1025 ?        Sl     0:01 zenity --info --text=Your Raspbian system has been upgraded to the l
     1049 ?        Sl     0:00 /usr/lib/gvfs/gvfs-udisks2-volume-monitor
     1051 ?        Ssl    0:00 /usr/lib/udisks2/udisksd --no-debug
     1063 ?        SNsl   0:00 /usr/lib/rtkit/rtkit-daemon
     1073 ?        Sl     0:00 /usr/lib/gvfs/gvfs-goa-volume-monitor
     1077 ?        Sl     0:00 /usr/lib/gvfs/gvfs-mtp-volume-monitor
     1083 ?        Sl     0:00 /usr/lib/gvfs/gvfs-gphoto2-volume-monitor
     1089 ?        Sl     0:00 /usr/lib/gvfs/gvfs-afc-volume-monitor
     1091 ?        Ss     0:00 /usr/lib/bluetooth/bluetoothd
     1104 ?        S      0:00 /bin/sh /usr/bin/start-pulseaudio-x11
     1105 ?        S      0:00 /usr/bin/xprop -root -spy
     1121 ?        Ssl    0:00 /usr/lib/menu-cache/menu-cached /tmp/.menu-cached-:0-pi
     1138 ?        Sl     0:00 /usr/lib/gvfs/gvfsd-trash --spawner :1.1 /org/gtk/gvfs/exec_spaw/0
     1508 ?        S      0:00 [kworker/u8:0]
     1523 ?        S      0:00 [kworker/1:2]
     1556 ?        S      0:00 [kworker/3:2]
     1641 ?        Sl     0:08 lxpanel --profile LXDE-pi
     1661 ?        S      0:00 [spi0]
     1747 ?        S      0:00 [kworker/2:0]
     1762 ?        Ss     0:00 sshd: pi [priv]
     1769 ?        R      0:00 sshd: pi@pts/0
     1771 pts/0    Ss     0:00 -bash
     1874 ?        Ssl    0:00 /usr/lib/packagekit/packagekitd
     1883 ?        S      0:00 [kworker/3:1]
     2153 ?        S      0:00 [kworker/1:0]
     2212 ?        S      0:00 [kworker/0:0]
     2241 ?        S      0:00 [kworker/u8:2]
     2286 pts/0    R+     0:00 ps -ax
    

  • Mod

    @fipster you already have one mysgw running

    371 ? Ss 1:51 /usr/local/bin/mysgw



  • Hello,
    I asking for help with same question. How I see there is no solution, so I try to explain step by step what I did and whats the problem I have.

    1. I install Domoticz on fresh Raspberry Pi Raspbian image

    2. Build a Raspberry Pi Ethernet Gateway by instructions (https://www.mysensors.org/build/raspberry)

    3. After that comand I have answer, that my SoC and Type of machine unknown (I using RPi 2):

    [SECTION] Detecting target machine.
      [OK] machine detected: SoC=unknown, Type=unknown, CPU=armv7l.
    

    But I found the solution about that in forum, where I change two lines of the configure file to "BCM2835":

    function detect_machine {
    ...
        case $hardware in
    ...
        BCM2835)
            soc="BCM2835"
            if [[ $machine == "Raspberry"* ]]; then
                local rev=($(detect_rpi_revision))
                if [[ $rev == "a02082" || $rev == "a22082" ]]; then
                    tp="RPi3"
                else
                    tp="Rpi2"
                fi
            fi
            ;;
    ...
    

    After changing it , all looks fine.

    1. I repeat
      • sudo ./configure --my-transport=nrf24 --my-gateway=ethernet --my-port=5003

    My board is recognized so I continue with gateway building instructions...

    • sudo make
    • sudo ./bin/mysgw -h
    • sudo ./bin/mysgw -d

    And I got results with no errors, gateway is running. Continue with comands

    • sudo make install
    • sudo systemctl enable mysgw.service
    • sudo systemctl start mysgw.service

    No errors. I connect one LED strip node to Domoticz and its working perfectly.
    But after ~10 minutes trying to on/off LED strip it doesn't work anymore. Nothing was changed. Checking the gateway with command:

    • sudo ./bin/mysgw -d

    And getting:

    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor
    

    Output of "ps -ax" command:

      PID TTY      STAT   TIME COMMAND
        1 ?        Ss     0:02 /sbin/init splash
        2 ?        S      0:00 [kthreadd]
        3 ?        S      0:00 [ksoftirqd/0]
        5 ?        S<     0:00 [kworker/0:0H]
        6 ?        S      0:00 [kworker/u8:0]
        7 ?        S      0:01 [rcu_sched]
        8 ?        S      0:00 [rcu_bh]
        9 ?        S      0:00 [migration/0]
       10 ?        S<     0:00 [lru-add-drain]
       11 ?        S      0:00 [cpuhp/0]
       12 ?        S      0:00 [cpuhp/1]
       13 ?        S      0:00 [migration/1]
       14 ?        S      0:00 [ksoftirqd/1]
       16 ?        S<     0:00 [kworker/1:0H]
       17 ?        S      0:00 [cpuhp/2]
       18 ?        S      0:00 [migration/2]
       19 ?        S      0:00 [ksoftirqd/2]
       21 ?        S<     0:00 [kworker/2:0H]
       22 ?        S      0:00 [cpuhp/3]
       23 ?        S      0:00 [migration/3]
       24 ?        S      0:00 [ksoftirqd/3]
       26 ?        S<     0:00 [kworker/3:0H]
       27 ?        S      0:00 [kdevtmpfs]
       28 ?        S<     0:00 [netns]
       29 ?        S      0:00 [khungtaskd]
       30 ?        S      0:00 [oom_reaper]
       31 ?        S<     0:00 [writeback]
       32 ?        S      0:00 [kcompactd0]
       33 ?        S<     0:00 [crypto]
       34 ?        S<     0:00 [bioset]
       35 ?        S<     0:00 [kblockd]
       36 ?        S<     0:00 [watchdogd]
       37 ?        S      0:00 [kworker/0:1]
       38 ?        S<     0:00 [rpciod]
       39 ?        S<     0:00 [xprtiod]
       40 ?        S      0:00 [kswapd0]
       41 ?        S<     0:00 [vmstat]
       42 ?        S<     0:00 [nfsiod]
       52 ?        S<     0:00 [kthrotld]
       53 ?        S<     0:00 [bioset]
       54 ?        S<     0:00 [bioset]
       55 ?        S<     0:00 [bioset]
       56 ?        S<     0:00 [bioset]
       57 ?        S<     0:00 [bioset]
       58 ?        S<     0:00 [bioset]
       59 ?        S<     0:00 [bioset]
       60 ?        S<     0:00 [bioset]
       61 ?        S<     0:00 [bioset]
       62 ?        S<     0:00 [bioset]
       63 ?        S<     0:00 [bioset]
       64 ?        S<     0:00 [bioset]
       65 ?        S<     0:00 [bioset]
       66 ?        S<     0:00 [bioset]
       67 ?        S<     0:00 [bioset]
       68 ?        S<     0:00 [bioset]
       69 ?        S<     0:00 [bioset]
       70 ?        S<     0:00 [bioset]
       71 ?        S<     0:00 [bioset]
       72 ?        S<     0:00 [bioset]
       73 ?        S<     0:00 [bioset]
       74 ?        S<     0:00 [bioset]
       75 ?        S<     0:00 [bioset]
       76 ?        S<     0:00 [bioset]
       77 ?        S<     0:00 [iscsi_eh]
       78 ?        S<     0:00 [dwc_otg]
       80 ?        S<     0:00 [DWC Notificatio]
       81 ?        S<     0:00 [VCHIQ-0]
       82 ?        S<     0:00 [VCHIQr-0]
       83 ?        S<     0:00 [VCHIQs-0]
       84 ?        S      0:00 [VCHIQka-0]
       85 ?        S<     0:00 [SMIO]
       88 ?        S<     0:00 [bioset]
       89 ?        S      0:00 [mmcqd/0]
       90 ?        S      0:00 [jbd2/mmcblk0p2-]
       91 ?        S<     0:00 [ext4-rsv-conver]
       93 ?        S      0:00 [kworker/3:1]
       94 ?        S<     0:00 [ipv6_addrconf]
      109 ?        S<     0:00 [kworker/1:1H]
      110 ?        S      0:00 [kworker/u8:1]
      115 ?        Ss     0:11 /lib/systemd/systemd-journald
      144 ?        S      0:00 [kworker/1:3]
      150 ?        Ss     0:00 /lib/systemd/systemd-udevd
      200 ?        S      0:00 [spi0]
      238 ?        S      0:00 [kworker/3:2]
      266 ?        Ssl    0:00 /lib/systemd/systemd-timesyncd
      288 ?        Ss     0:00 /usr/bin/dbus-daemon --system --address=systemd: --nofork --nopidfile --systemd-activation
      291 ?        Ss     0:00 /usr/sbin/cron -f
      292 ?        Ssl    0:04 /usr/sbin/rsyslogd -n
      293 ?        Ss     0:00 avahi-daemon: running [raspberrypi.local]
      295 ?        Rs    80:53 /usr/local/bin/mysgw
      297 ?        Ss     0:00 /lib/systemd/systemd-logind
      299 ?        Ss     0:00 /usr/sbin/thd --triggers /etc/triggerhappy/triggers.d/ --socket /run/thd.socket --user nobody --deviceglob /dev/input/event*
      309 ?        S      0:00 avahi-daemon: chroot helper
      320 ?        S<     0:00 [cfg80211]
      324 ?        Ss     0:00 /sbin/dhcpcd -q -b
      359 ?        Ss     0:00 /usr/sbin/sshd -D
      378 ?        Ssl    0:00 /usr/sbin/lightdm
      381 ?        S<     0:00 [kworker/2:1H]
      390 tty1     Ss     0:00 /bin/login -f
      393 ?        Ss+    0:00 /sbin/agetty --keep-baud 115200,38400,9600 ttyAMA0 vt220
      400 tty7     Ssl+   0:03 /usr/lib/xorg/Xorg :0 -seat seat0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch
      402 ?        Ssl    0:16 /home/pi/domoticz/domoticz -daemon -www 8080 -sslwww 443
      403 ?        S<     0:00 [kworker/3:1H]
      431 ?        Sl     0:00 lightdm --session-child 14 17
      439 ?        Ss     0:00 /lib/systemd/systemd --user
      442 ?        S      0:00 (sd-pam)
      447 ?        Ssl    0:00 /usr/bin/lxsession -s LXDE-pi -e LXDE
      456 ?        Ss     0:00 /usr/bin/dbus-daemon --session --address=systemd: --nofork --nopidfile --systemd-activation
      501 tty1     S+     0:00 -bash
      520 ?        Ss     0:00 /usr/bin/ssh-agent x-session-manager
      526 ?        Ssl    0:00 /usr/lib/gvfs/gvfsd
      531 ?        Sl     0:00 /usr/lib/gvfs/gvfsd-fuse /run/user/1000/gvfs -f -o big_writes
      547 ?        S      0:01 openbox --config-file /home/pi/.config/openbox/lxde-pi-rc.xml
      549 ?        Sl     0:00 lxpolkit
      551 ?        Sl     0:12 lxpanel --profile LXDE-pi
      553 ?        Sl     0:01 pcmanfm --desktop --profile LXDE-pi
      561 ?        Ss     0:00 /usr/bin/ssh-agent -s
      570 ?        Ssl    0:00 /usr/lib/policykit-1/polkitd --no-debug
      585 ?        Ssl    0:00 /usr/lib/menu-cache/menu-cached /run/user/1000/menu-cached-:0
      589 ?        Ssl    0:00 /usr/lib/gvfs/gvfs-udisks2-volume-monitor
      592 ?        Ssl    0:00 /usr/lib/udisks2/udisksd --no-debug
      603 ?        Ssl    0:00 /usr/lib/gvfs/gvfs-goa-volume-monitor
      607 ?        Ssl    0:00 /usr/lib/gvfs/gvfs-mtp-volume-monitor
      611 ?        Ssl    0:00 /usr/lib/gvfs/gvfs-gphoto2-volume-monitor
      620 ?        Ssl    0:00 /usr/lib/gvfs/gvfs-afc-volume-monitor
      633 ?        Sl     0:00 /usr/lib/gvfs/gvfsd-trash --spawner :1.4 /org/gtk/gvfs/exec_spaw/0
      733 ?        S      0:00 sudo ./bin/mysgw -d
      737 ?        R     80:45 ./bin/mysgw -d
      751 ?        S<     0:00 [kworker/0:1H]
      760 ?        S      0:00 [kworker/0:0]
      761 ?        S      0:00 [kworker/1:1]
      766 ?        Ss     0:00 sshd: pi [priv]
      776 ?        R      0:01 sshd: pi@pts/1
      779 pts/1    Ss     0:00 -bash
      805 pts/1    T      0:00 sudo ./bin/mysgw -d
      809 pts/1    T      0:25 ./bin/mysgw -d
      850 ?        S      0:00 [kworker/2:1]
      857 ?        S      0:00 [kworker/2:0]
      862 pts/1    R+     0:00 ps -ax
    

    cat /sys/firmware/devicetree/base/model

    Raspberry Pi 2 Model B Rev 1.1
    

    Don't know how to fix that
    Sep 24 21:37:15 raspberrypi mysgw: accept: Bad file descriptor

    Looks like I using gateway building instructions step by step, but something is missing... Thanks.


  • Mod

    @jacikaas as can be seen from the ps output, mysgw is already running:

    295 ?        Rs    80:53 /usr/local/bin/mysgw
    

    It is running because you started it with

    sudo systemctl start mysgw.service
    

    So when you try to start another instance of mysgw by running

    sudo ./bin/mysgw -d
    

    the new instance tries to start listening on the same port, which it can't because it is already in use.

    As mentioned in the troubleshooting section, look in /var/log/syslog to see the gateway output of the existing instance. Don't start a new one.

    Also, it seems your sudo key has gotten stuck 😞 If you missed that not every command is preceeded by sudo in the build instructions, maybe it is worth considering that you missed something else?



  • @mfalkvidd

    Thank You for the answer.

    @mfalkvidd said in mysgw: bind: Address already in use:

    As mentioned in the troubleshooting section, look in /var/log/syslog to see the gateway output of the existing instance. Don't start a new one.

    Ohh... Thats a lot more clear now... I thought command "sudo ./bin/mysgw -d" is not a service start, but just something like output mirror. Like "tail". Could I somehow use tail for watching real time output on ./bin/mysgw -d ?

    Also, it seems your sudo key has gotten stuck 😞 If you missed that not every command is preceeded by sudo in the build instructions, maybe it is worth considering that you missed something else?

    Sorry for dumb questions, but how I make that sudo key stuck? It's becose of that I start a few mysgw services?

    Another silly question, becose I'm very "advanced user" in UNIX, my best friend is called desktop there, and I know basically just install, nano, cp, rm commands, I need to ask 🙂 Is there should be difference if I will use "make" instead of "sudo make". Sudo means that I run this command by root user, but does it make difference between "make" or "sudo make"? And if I remember clearly if I run only "make" - raspberry pi starts to swearing, but with sudo, it's ok.

    When I install the gateway by command "sudo make install" I can see that installing was successful, there is info that if I want to run this on boot I need to run two lines:

    • sudo systemctl enable mysgw.service
    • sudo systemctl start mysgw.service

    But now, I guess, I do not need them both, because start on boot is described in "sudo make install"?


Log in to reply
 

Suggested Topics

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts