Multiple Sensors on a single node?



  • I am having a problem getting HA to read multiple sensors from a single node. What am i missing? I am using the sample DHT Code below.

    // Enable debug prints
    #define MY_DEBUG
    
    // Enable and select radio type attached 
    #define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    //#define MY_RS485
    
    #include <SPI.h>
    #include <MySensors.h>  
    #include <DHT.h>
    
    // Set this to the pin you connected the DHT's data pin to
    #define DHT_DATA_PIN 2
    
    // Set this offset if the sensor has a permanent small offset to the real temperatures
    #define SENSOR_TEMP_OFFSET 0
    
    // Sleep time between sensor updates (in milliseconds)
    // Must be >1000ms for DHT22 and >2000ms for DHT11
    static const uint64_t UPDATE_INTERVAL = 60000;
    
    // Force sending an update of the temperature after n sensor reads, so a controller showing the
    // timestamp of the last update doesn't show something like 3 hours in the unlikely case, that
    // the value didn't change since;
    // i.e. the sensor would force sending an update every UPDATE_INTERVAL*FORCE_UPDATE_N_READS [ms]
    static const uint8_t FORCE_UPDATE_N_READS = 10;
    
    #define CHILD_ID_HUM 0
    #define CHILD_ID_TEMP 1
    
    float lastTemp;
    float lastHum;
    uint8_t nNoUpdatesTemp;
    uint8_t nNoUpdatesHum;
    bool metric = true;
    
    MyMessage msgHum(CHILD_ID_HUM, V_HUM);
    MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
    DHT dht;
    
    
    void presentation()  
    { 
      // Send the sketch version information to the gateway
      sendSketchInfo("TemperatureAndHumidity", "1.1");
    
      // Register all sensors to gw (they will be created as child devices)
      present(CHILD_ID_TEMP, S_TEMP);
      present(CHILD_ID_HUM, S_HUM);
    
    
      metric = getControllerConfig().isMetric;
    }
    
    
    void setup()
    {
      dht.setup(DHT_DATA_PIN); // set data pin of DHT sensor
      if (UPDATE_INTERVAL <= dht.getMinimumSamplingPeriod()) {
        Serial.println("Warning: UPDATE_INTERVAL is smaller than supported by the sensor!");
      }
      // Sleep for the time of the minimum sampling period to give the sensor time to power up
      // (otherwise, timeout errors might occure for the first reading)
      sleep(dht.getMinimumSamplingPeriod());
    }
    
    
    void loop()      
    {  
      // Force reading sensor, so it works also after sleep()
      dht.readSensor();
    
      // Get temperature from DHT library
      float temperature = dht.getTemperature();
      if (isnan(temperature)) {
        Serial.println("Failed reading temperature from DHT!");
      } else if (temperature != lastTemp || nNoUpdatesTemp == FORCE_UPDATE_N_READS) {
        // Only send temperature if it changed since the last measurement or if we didn't send an update for n times
        lastTemp = temperature;
        if (!metric) {
          temperature = dht.toFahrenheit(temperature);
        }
        // Reset no updates counter
        nNoUpdatesTemp = 0;
        temperature += SENSOR_TEMP_OFFSET;
        send(msgTemp.set(temperature, 1));
    
        #ifdef MY_DEBUG
        Serial.print("T: ");
        Serial.println(temperature);
        #endif
      } else {
        // Increase no update counter if the temperature stayed the same
        nNoUpdatesTemp++;
      }
    
      // Get humidity from DHT library
      float humidity = dht.getHumidity();
      if (isnan(humidity)) {
        Serial.println("Failed reading humidity from DHT");
      } else if (humidity != lastHum || nNoUpdatesHum == FORCE_UPDATE_N_READS) {
        // Only send humidity if it changed since the last measurement or if we didn't send an update for n times
        lastHum = humidity;
        // Reset no updates counter
        nNoUpdatesHum = 0;
        send(msgHum.set(humidity, 1));
    
        #ifdef MY_DEBUG
        Serial.print("H: ");
        Serial.println(humidity);
        #endif
      } else {
        // Increase no update counter if the humidity stayed the same
        nNoUpdatesHum++;
      }
    
      // Sleep for a while to save energy
      sleep(UPDATE_INTERVAL```


  • I feel smart now, After resetting the home assistant server I noticed that my motion sensor (Previously tested) was assigned to that node on child_id 1 After changing my temperature child_id to 2 The temperature showed up properly.


  • Mod

    You didn't specify the NODE ID, so it probably got the last one used on that board.



  • I have previously assigned the node and for testing purposes I don't mind it remaining the same. It was surprising to me that Home Assistant doesn't automatically detect sketch adjustments when the node connects. My next step is to learn how to clean up home assistants records to remove unwanted test data.


  • Mod

    You'd better change node ID if you want to change the sensors type in the sketch or delete sensor in Home assistant before uploading new sketch. You need to help the system a little, it can't do everything on its own


  • Plugin Developer

    @Jeff-Willecke

    Hi!

    If using JSON persistence, you can manually edit the JSON persistence file and remove old stale sensors. Make sure your retain the JSON structure.



  • Editing the json took care of all the junk. I appreciate the help.



  • you can use https://jsonformatter.org/json-editor to edit json data.


Log in to reply
 

Suggested Topics

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts