Domoticz(Raspberry) with Mysensor USB gateway without Radio



  • Hello,

    I try to create USB gateway without radio, but my domoticz under raspberry don't see this gateway.

    Could you check my code?
    Thanks

    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Enable and select radio type attached
    //#define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    
    // Set LOW transmit power level as default, if you have an amplified NRF-module and
    // power your radio separately with a good regulator you can turn up PA level.
    //#define MY_RF24_PA_LEVEL RF24_PA_LOW
    
    // Enable serial gateway
    #define MY_GATEWAY_SERIAL
    
    // Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
    #if F_CPU == 8000000L
    #define MY_BAUD_RATE 38400
    #endif
    
    // Enable inclusion mode
    #define MY_INCLUSION_MODE_FEATURE
    // Enable Inclusion mode button on gateway
    //#define MY_INCLUSION_BUTTON_FEATURE
    
    // Inverses behavior of inclusion button (if using external pullup)
    //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
    
    // Set inclusion mode duration (in seconds)
    #define MY_INCLUSION_MODE_DURATION 60
    // Digital pin used for inclusion mode button
    //#define MY_INCLUSION_MODE_BUTTON_PIN  3
    
    // Set blinking period
    #define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Inverses the behavior of leds
    //#define MY_WITH_LEDS_BLINKING_INVERSE
    
    // Flash leds on rx/tx/err
    // Uncomment to override default HW configurations
    //#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
    //#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
    //#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED
    
    #include <MySensors.h>
    #include <SPI.h>
    
    #define CHILD_ID 1   // Id of the sensor child
    
    #define IN_Sejour_Presence1  2  // Arduino Digital I/O pin number for Presence
    #define IN_Sejour_Presence2  3  // Arduino Digital I/O pin number for Presence
    #define IN_Sejour_Presence3  4  // Arduino Digital I/O pin number for Presence
    #define IN_ChParents_Presence  5  // Arduino Digital I/O pin number for Presence
    
    #define NUMBER_OF_INPUT 4 // Total number of attached input port
    
    #define RELAY_Sejour_Volet1_Bas  22  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet1_Stop  23  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet1_Haut  24  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet2_Bas  25  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet2_Stop  26  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet2_Haut  27  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet3_Bas  28  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet3_Stop  29  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Volet3_Haut  30  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Lumiere1  31  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Lumiere2  32  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Lumiere3  33  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Chauffage1  34  // Arduino Digital I/O pin number for relay
    #define RELAY_Sejour_Chauffage2  35  // Arduino Digital I/O pin number for relay
    
    #define RELAY_SdJ_Volet1_Bas  37  // Arduino Digital I/O pin number for relay
    #define RELAY_SdJ_Volet1_Stop  38  // Arduino Digital I/O pin number for relay
    #define RELAY_SdJ_Volet1_Haut  39  // Arduino Digital I/O pin number for relay
    
    #define RELAY_ChParents_Volet_Bas  41  // Arduino Digital I/O pin number for relay
    #define RELAY_ChParents_Volet_Stop  42  // Arduino Digital I/O pin number for relay
    #define RELAY_ChParents_Volet_Haut  43  // Arduino Digital I/O pin number for relay
    #define RELAY_ChParents_Lumiere  44  // Arduino Digital I/O pin number for relay
    #define RELAY_ChParents_Chauffage  45  // Arduino Digital I/O pin number for relay
    
    #define NUMBER_OF_RELAYS 32 // Total number of attached relays port 22 to 53
    #define RELAY_ON 1  // GPIO value to write to turn on attached relay
    #define RELAY_OFF 0 // GPIO value to write to turn off attached relay
    
    unsigned long Duree_Sejour_Lum1 = 60000;
    unsigned long Duree_Sejour_Lum2 = 60000;
    unsigned long Duree_Sejour_Lum3 = 60000;
    unsigned long Duree_ChParents_Lum = 60000;
    
    unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
    
    bool IN_Sejour_Presence1_Etat = LOW;
    bool IN_Sejour_Presence1_Etat_Avant = LOW;
    bool IN_Sejour_Presence2_Etat = LOW;
    bool IN_Sejour_Presence2_Etat_Avant = LOW;
    bool IN_Sejour_Presence3_Etat = LOW;
    bool IN_Sejour_Presence3_Etat_Avant = LOW;
    bool IN_ChParents_Presence_Etat = LOW;
    bool IN_ChParents_Presence_Etat_Avant = LOW;
    
    // Initialize motion message
    MyMessage msg(CHILD_ID, V_TRIPPED);
    
    void before()
    {
       // Send the sketch version information to the gateway and Controller
       // sendSketchInfo("MySensorBas", "1.0");
       
        for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
            // Then set relay pins in output mode
            pinMode(pin, OUTPUT);
            // Set relay to last known state (using eeprom storage)
            digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
        }
         pinMode(IN_Sejour_Presence1, INPUT);
         pinMode(IN_Sejour_Presence2, INPUT);
         pinMode(IN_Sejour_Presence3, INPUT);
         pinMode(IN_ChParents_Presence, INPUT);
    }
    
    void setup()
    {
    
    }
    
    void presentation()
    {
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Salon_Parents_SdJ", "1.0");
    
        for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
            // Register all sensors to gw (they will be created as child devices)
            present(sensor, S_BINARY);
        }
    
         for (int sensor=IN_Sejour_Presence1, pin=IN_Sejour_Presence1; sensor<=NUMBER_OF_INPUT; sensor++, pin++) {
            // Register all sensors to gw (they will be created as child devices)
            present(sensor, S_MOTION);
        }
    }
    
    void loop()
    {
        // Read digital motion value
        IN_Sejour_Presence1_Etat = digitalRead(IN_Sejour_Presence1);
        if (IN_Sejour_Presence1_Etat != IN_Sejour_Presence1_Etat_Avant){
          if (IN_Sejour_Presence1_Etat == HIGH){
      //          Serial.println(IN_Sejour_Presence1_Etat);
                send(msg.set(IN_Sejour_Presence1_Etat?"1":"0"));  // Send tripped value to gw
          }
          IN_Sejour_Presence1_Etat_Avant = IN_Sejour_Presence1_Etat;
        }
     
        // Read digital motion value
        IN_Sejour_Presence2_Etat = digitalRead(IN_Sejour_Presence2);
        if (IN_Sejour_Presence2_Etat != IN_Sejour_Presence2_Etat_Avant){
          if (IN_Sejour_Presence2_Etat == HIGH){
      //          Serial.println(IN_Sejour_Presence2_Etat);
                send(msg.set(IN_Sejour_Presence2_Etat?"1":"0"));  // Send tripped value to gw
          }
          IN_Sejour_Presence2_Etat_Avant = IN_Sejour_Presence2_Etat;
        }
    
        // Read digital motion value
        IN_Sejour_Presence3_Etat = digitalRead(IN_Sejour_Presence3);
        if (IN_Sejour_Presence3_Etat != IN_Sejour_Presence3_Etat_Avant){
          if (IN_Sejour_Presence3_Etat == HIGH){
      //          Serial.println(IN_Sejour_Presence3_Etat);
                send(msg.set(IN_Sejour_Presence3_Etat?"1":"0"));  // Send tripped value to gw
          }
          IN_Sejour_Presence3_Etat_Avant = IN_Sejour_Presence3_Etat;
        }
    
        // Read digital motion value
        IN_ChParents_Presence_Etat = digitalRead(IN_ChParents_Presence);
        if (IN_ChParents_Presence_Etat != IN_ChParents_Presence_Etat_Avant){
          if (IN_ChParents_Presence_Etat == HIGH){
      //          Serial.println(IN_ChParents_Presence_Etat);
                send(msg.set(IN_ChParents_Presence_Etat?"1":"0"));  // Send tripped value to gw
          }
          IN_ChParents_Presence_Etat_Avant = IN_ChParents_Presence_Etat;
        }
    }
    
    void receive(const MyMessage &message)
    {
        // We only expect one type of message from controller. But we better check anyway.
        if (message.type==V_STATUS) {
            // Change relay state
            digitalWrite(message.sensor-1+RELAY_Sejour_Volet1_Bas, message.getBool()?RELAY_ON:RELAY_OFF);
            // Store state in eeprom
            saveState(message.sensor, message.getBool());
            // Write some debug info
       //     Serial.print("Incoming change for sensor:");
       //     Serial.print(message.sensor);
       //     Serial.print(", New status: ");
       //     Serial.println(message.getBool());
        }
    }
    

  • Mod

    Have you tried commenting mydebug?



  • Yes, I Have:
    0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
    0;255;3;0;9;MCO:BGN:BFR
    0;255;3;0;9;TSM:INIT
    0;255;3;0;9;TSF:WUR:MS=0
    0;255;3;0;9;!TSM:INIT:TSP FAIL
    0;255;3;0;9;TSM:FAIL:CNT=1
    0;255;3;0;9;TSM:FAIL:PDT.

    But I don't know why I have on first error :Transport device initialization failed



  • When I put serial gateway code availiable on MySensor Site, I have the same error.

    0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
    0;255;3;0;9;TSM:INIT
    0;255;3;0;9;TSF:WUR:MS=0
    0;255;3;0;9;!TSM:INIT:TSP FAIL
    0;255;3;0;9;TSM:FAIL:CNT=1
    0;255;3;0;9;TSM:FAIL:PDT

    I try to do MySensor USB gateway without radio for physical IO on Arduino(to have relay)


  • Mod

    It's actually weird, but if only need relays, you can control gpio directly from domoticz.



  • Ok, I find.

    Sketchinfo was in Presntation, and should be in setup.

    void setup()
    {
        // Send the sketch version information to the gateway and Controller
        sendSketchInfo("Salon_Parents_SdJ", "1.0");
    
        for (int sensor=RELAY_Sejour_Volet1_Bas, pin=RELAY_Sejour_Volet1_Bas; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
            // Register all sensors to gw (they will be created as child devices)
            present(sensor, S_BINARY);
        }
    
         for (int sensor=IN_Sejour_Presence1, pin=IN_Sejour_Presence1; sensor<=NUMBER_OF_INPUT; sensor++, pin++) {
            // Register all sensors to gw (they will be created as child devices)
            present(sensor, S_MOTION);
        }
    }```

Log in to reply
 

Suggested Topics

  • 8
  • 2
  • 1
  • 2
  • 3
  • 1

1
Online

11.2k
Users

11.1k
Topics

112.5k
Posts