irrigation controller arduino mega doesn't work anymore



  • Arduino Mega Node not working anymore
    I have an arduino mega used for automated irrigation after a year of service the node is not responding anymore.
    The node runs on mysensor 2.1.1
    The serial monitor shows the following

    0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
    3 TSM:INIT
    4 TSF:WUR:MS=0
    11 TSM:INIT:TSP OK
    13 TSF:SID:OK,ID=5
    15 TSM:FPAR
    51 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    2058 !TSM:FPAR:NO REPLY
    2060 TSM:FPAR
    2096 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    2910 TSF:MSG:READ,11-11-5,s=255,c=3,t=8,pt=1,l=1,sg=0:3
    2915 TSF:MSG:FPAR OK,ID=11,D=4
    4104 TSM:FPAR:OK
    4105 TSM:ID
    4106 TSM:ID:OK
    4108 TSM:UPL
    4113 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
    6120 TSM:UPL
    6125 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
    8132 TSM:UPL
    8137 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
    8212 TSF:MSG:READ,0-11-5,s=255,c=3,t=25,pt=1,l=1,sg=0:4
    8217 TSF:MSG:PONG RECV,HP=4
    8219 TSM:UPL:OK
    8221 TSM:READY:ID=5,PAR=11,DIS=4
    8246 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
    10255 TSF:MSG:SEND,5-5-11-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
    10297 !TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=NACK:11
    12307 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=11,pt=0,l=12,sg=0,ft=1,st=OK:Bewässerung
    12351 !TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=NACK:2.1
    12388 TSF:MSG:SEND,5-5-11-0,s=13,c=0,t=6,pt=0,l=0,sg=0,ft=1,st=OK:
    12396 TSF:MSG:SEND,5-5-11-0,s=14,c=0,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    12437 !TSF:MSG:SEND,5-5-11-0,s=15,c=0,t=16,pt=0,l=0,sg=0,ft=0,st=NACK:
    12445 TSF:MSG:SEND,5-5-11-0,s=1,c=0,t=7,pt=0,l=0,sg=0,ft=1,st=OK:
    12465 TSF:MSG:SEND,5-5-11-0,s=9,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
    12474 TSF:MSG:SEND,5-5-11-0,s=2,c=0,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    12482 TSF:MSG:SEND,5-5-11-0,s=10,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
    12492 TSF:MSG:SEND,5-5-11-0,s=3,c=0,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
    12533 !TSF:MSG:SEND,5-5-11-0,s=11,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=NACK:
    12541 TSF:MSG:SEND,5-5-11-0,s=4,c=0,t=7,pt=0,l=0,sg=0,ft=1,st=OK:
    12582 !TSF:MSG:SEND,5-5-11-0,s=12,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=NACK:
    12590 MCO:REG:REQ
    12614 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=OK:2
    14625 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
    16635 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
    18647 TSF:MSG:SEND,5-5-11-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
    18738 TSF:MSG:READ,0-11-5,s=255,c=3,t=27,pt=1,l=1,sg=0:1
    18743 MCO:PIM:NODE REG=1
    18746 MCO:BGN:STP
    

    after MCO:BGN:STP nothing happens
    what does MCO:BGN:STP mean?
    greets
    patrick


  • Mod

    @patrick-schaerer https://forum.mysensors.org/topic/666/debug-faq-and-how-ask-for-help/ has information on how to interpret the log messages and a link to the log parser which will help you interpret them.

    There are a lot of st=NACK messages which means that radio communication from the node to the gateway has trouble. This is usually a power or range issue. See the link above for flowcharts on how to troubleshoot.



  • thank you for the link

    18743 MCO:PIM:NODE REG=1	Registration response received, registration status 1
    18746 MCO:BGN:STP	Callback setup()
    

    What is Registration status 1?
    Does Callback setup() reinitialize the node?



  • I found the problem ...
    due to a defective sensor (light meter) the arduino could not initialize correctly.
    I think that is why it was calling back setup()


Log in to reply
 

Suggested Topics

  • 1
  • 2
  • 5
  • 3
  • 2
  • 2

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts