Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

ESP-LINK "just works" with Domoticz

NeverDie Hero Member last edited by NeverDie

First time I tried it with Domoticz, and I was easily able to set it up as an ethernet connection (though it's actually wi-fi). I just entered the IP address and the port number of the ESP-LINK MySensors gateway node into Domoticz, and then everything just magically works. Domoticz immediately picked up on the MySensors temperature node that was communicating with the gateway.

https://www.openhardware.io/view/491/PA-LNA-nRF52832-ESP-LINK-Shield-for-Wemos-D1-Mini-ESP8266
Reply Quote 0
1 Reply Last reply

1
Posts

1516
Views

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

5

0
Votes

5
Posts

2061
Views

@karenbobiv I doubt it's related to the MySensors communication. Are you using a Dallas temp sensor? Could you check that the is actually connected to the dallas sensor by using isConnected(). When googling your problem I found a few hits on -196.6 which is the error code (DEVICE_DISCONNECTED) converted to Fahrenheit. Start debug mode (Config.h) to see what the sensor actually sends.
How to get the bad status (red) for Temperature Node
Domoticz • • giangired

5

0
Votes

5
Posts

55
Views

Thanks everyone for the answers. However what I would like to do is create a routine with Dzvents that when I have the "red" indication (as shown in the image) causes a switch to operate which cuts the voltage to a device. The value of ".lastUpdate.minutesAgo" seems not to be the right solution because it continues to be increased in any case, regardless of the temperature value and the status of the "red" or normal indication.
Calculate Delta T of two temperature sensors with lua
Domoticz • temperature • • Mela

1

0
Votes

1
Posts

9
Views

No one has replied
Trying to automate in Domoticz
Domoticz • • Feliw05

4

0
Votes

4
Posts

33
Views

the problem is "if (switch.state == 'On') then" that not works, write: if (switch.active) then or if (switch.inActive) then Device attributes and methods for all devices
eventsystem: problem writing file
Domoticz • • Feliw05

2

0
Votes

2
Posts

11
Views

Save the script directly from Windows and test if it can be opened in Domoticz.
Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

8

0
Votes

8
Posts

896
Views

Someone know if it is problem with Domoticz or MySensors?

ESP-LINK "just works" with Domoticz

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

Calculate Delta T of two temperature sensors with lua
Domoticz • temperature • • Mela

Trying to automate in Domoticz
Domoticz • • Feliw05

eventsystem: problem writing file
Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

ESP-LINK "just works" with Domoticz

Suggested Topics

Vera Gateway Versions Troubleshooting • • karenbobiv

How to get the bad status (red) for Temperature Node Domoticz • • giangired

Calculate Delta T of two temperature sensors with lua Domoticz • temperature • • Mela

Trying to automate in Domoticz Domoticz • • Feliw05

eventsystem: problem writing file Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz Domoticz • • Tmaster

0Online

11.2kUsers

11.1kTopics

112.5kPosts

Vera Gateway Versions
Troubleshooting • • karenbobiv

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

Calculate Delta T of two temperature sensors with lua
Domoticz • temperature • • Mela

Trying to automate in Domoticz
Domoticz • • Feliw05

eventsystem: problem writing file
Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts