Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Sensebender Gateway pin mapping

betgear last edited by

Hi,

I'm trying to connect a W5500 ethernet module to the sensebender gateway, to that end I'm trying to decipher how the pins on the SAMD are mapped to pin numbers and I'm getting a little confused.

Looking in the W5100.h file library within the samd/1.05/libraries/ethernet I can see ETHERNET_SHIELD_SPI_CS is mapped to pin 24 (PB11), which on the sensebender schematic is labelled NET_RST and not NET_SS which is pin 28.

The variants.h file for this micro doesn't appear to throw any light on the subject, as the defines for the W5100 maps PIN_SPI1_MISO to pin 22, this physical pin is GND in the schematic.

Any help most appreciated, or a link to a tutorial would be cool

Thanks,

Glen.
Reply Quote 0
1 Reply Last reply

1
Posts

499
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50407
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

14
Views

No one has replied
Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

9

0
Votes

9
Posts

61
Views

Great! I'm glad it works and thank you very much for reporting back!
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

26
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?

Sensebender Gateway pin mapping

Suggested Topics

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Arduino Nano Every problem
Hardware • • hakha4

1
Online

11.2k
Users

11.1k
Topics

112.5k
Posts

Sensebender Gateway pin mapping

Suggested Topics

Over the air updates General Discussion • • ToSa

Sensors and more Hardware • • Robert Leverett

Node with only sendBatteryLevel into Home Assistant Hardware • • Arno

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

Arduino Nano Every problem Hardware • • hakha4

1Online

11.2kUsers

11.1kTopics

112.5kPosts

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

Node with only sendBatteryLevel into Home Assistant
Hardware • • Arno

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Arduino Nano Every problem
Hardware • • hakha4

1
Online

11.2k
Users

11.1k
Topics

112.5k
Posts