ESP8266 CH340 Error on gateway



  • Hello,
    I use a esp8266 de type CH340 NodeMcu V3 .

    here is my code:

    // Enable debug prints to serial monitor
    #define MY_DEBUG
    
    // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
    #define MY_BAUD_RATE 9600
    
    // Enables and select radio type (if attached)
    #define MY_RADIO_NRF24
    //#define MY_RADIO_RFM69
    //#define MY_RADIO_RFM95
    
    #define MY_GATEWAY_ESP8266
    
    #define MY_WIFI_SSID "yyyyyyy"
    #define MY_WIFI_PASSWORD "xxxxxx"
    
    // Enable UDP communication
    //#define MY_USE_UDP  // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS below
    
    // Set the hostname for the WiFi Client. This is the hostname
    // it will pass to the DHCP server if not static.
    //#define MY_HOSTNAME "sensor-gateway"
    
    // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
    //#define MY_IP_ADDRESS 192,168,1,102
    
    // If using static ip you can define Gateway and Subnet address as well
    //#define MY_IP_GATEWAY_ADDRESS 192,168,1,254
    //#define MY_IP_SUBNET_ADDRESS 255,255,255,0
    
    // The port to keep open on node server mode
    #define MY_PORT 5003
    
    // How many clients should be able to connect to this gateway (default 1)
    #define MY_GATEWAY_MAX_CLIENTS 2
    
    // Controller ip address. Enables client mode (default is "server" mode).
    // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
    //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
    
    // Enable inclusion mode
    //#define MY_INCLUSION_MODE_FEATURE
    
    // Enable Inclusion mode button on gateway
    //#define MY_INCLUSION_BUTTON_FEATURE
    // Set inclusion mode duration (in seconds)
    //#define MY_INCLUSION_MODE_DURATION 60
    // Digital pin used for inclusion mode button
    //#define MY_INCLUSION_MODE_BUTTON_PIN D1
    
    // Set blinking period
    //#define MY_DEFAULT_LED_BLINK_PERIOD 300
    
    // Flash leds on rx/tx/err
    // Led pins used if blinking feature is enabled above
    //#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
    //#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
    //#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
    
    #if defined(MY_USE_UDP)
    #include <WiFiUdp.h>
    #endif
    
    #include <ESP8266WiFi.h>
    #include <MySensors.h>
    
    #define CHILD_ID 30
    volatile uint32_t watt = 10;
    MyMessage msgContacteur(CHILD_ID, V_TRIPPED);
    //uint32_t SEND_FREQUENCY = 20000; // Minimum time between send (in milliseconds). We don't want to spam the gateway.
    
      MyMessage wattMsg(CHILD_ID,V_WATT);
      MyMessage kWhMsg(CHILD_ID,V_KWH);
      MyMessage pcMsg(CHILD_ID,V_VAR1);
      
    void setup()
    {
    	// Setup locally attached sensors
    }
    
    void presentation()
    {
    	sendSketchInfo("MySensors Watt", "1.0");
        present(CHILD_ID, S_POWER);
    
    }
    
    void loop()
    {
    	// Send locally attached sensors data here
      send(wattMsg.set(watt));  // Send watt value to gw
                  Serial.print("Watt:");
                Serial.println(watt);
    }
    

    here are the errors:

    90 TSF:LRT:OK
    105 TSM:INIT
    119 TSF:WUR:MS=0
    142 !TSM:INIT:TSP FAIL
    166 TSM:FAIL:CNT=1
    scandone
    state: 0 -> 2 (b0)
    state: 2 -> 3 (0)
    state: 3 -> 5 (10)
    add 0
    aid 3
    cnt 
    
    connected with yyyyyyyyyy, channel 1
    dhcp client start...
    334 TSM:FAIL:DIS
    352 TSF:TDI:TSL
    ip:192.168.1.102,mask:255.255.255.0,gw:192.168.1.254
    10370 TSM:FAIL:RE-INIT
    10394 TSM:INIT
    10415 !TSM:INIT:TSP FAIL
    10441 TSM:FAIL:CNT=2
    10463 TSM:FAIL:DIS
    10483 TSF:TDI:TSL
    

    do you have an idea about the problem?

    cordially


  • Mod

    @sam85 said in ESP8266 CH340 Error on gateway:

    10415 !TSM:INIT:TSP FAIL

    Hi and welcome to the forum!

    TSP FAIL indicates a problem with the radio communication. Triple check your wiring or try with a different radio.


  • Mod

    or add // before #define MY_RADIO_NRF24 if you don't plan to use a radio.



  • @sam85 #if defined(MY_USE_UDP) // is it defined somewhere?


Log in to reply
 

Suggested Topics

0
Online

11.2k
Users

11.1k
Topics

112.5k
Posts