Are you sure? Post it on domoticz forum. I can`t test this.

Great news guys!!!
Take a look at Beta version #3448.
http://www.domoticz.com/forum/viewtopic.php?f=42&t=7839&p=59180#p59163

Hello @yury
Did you find workaround ?

You could ask gizmocuz for help.
https://www.domoticz.com/forum/viewtopic.php?f=42&t=7839&p=58270#p58270

@tekka

@tekka said:

@NewFolk said:

@tekka is there a way to change the default channel in MYSbootloader ?

Yes, but for that you'll have to re-compile it.

Could you help me to find where to change channel? It is in MYSBootloaderHW.h ?

@cdr said:

@tekka I feel really, really, REALLY stupid;

I changed the channel in the mysensors config.h to 77, this was the reason no node would ever show up since the default mysbootloader uses the default channel 76.

D'OH

Thanks for your patience and help, everything is working now and I'm really happy!

@tekka is there a way to change the default channel in MYSbootloader ?

Let me UP this thread. mb @tekka could help?

@tekka
Hello, could you help me with uploading bootloader. I stuck on Step 5 step-by-step manual and get error

Arduino: 1.6.4 (Mac OS X), Плата"ATmega328 16Mhz MYSBootloader"
avrdude: error: could not find USB device with vid=0x16c0 pid=0x5dc vendor='www.fischl.de' product='USBasp'

I`m using 16Mhz pro mini clone and FTDI232

@Mrlynx
I power node on MYS board from iPhone wall and with USB through FTDI both give me the same 3.324 on 3.3 pin.
And GW is powered thought RPI USB - original UNO / clone nano 5v - Adapter Board NRF24L01+ http://www.ebay.com/itm/200960749614?rmvSB=true

I have just tried to move antenna radio to node and simple radio to GW and it`s work.
Bud it bad workaround.

PS will try to change node and GW to RF_PA_HIGH

edit: change to hight and i saw same ok status. Then I change to

#define RF24_PA_LEVEL 	   RF24_PA_LOW

And get 3 successful initialization in a row. So I will test tonight with DHT22.
Thank you

I had NRF24L01+PA+LNA Antenna version on the gateway. And simple NRF24L01+ on node.
Today I tried to set GW PA Level to hight by changing MyConfig.h. After this I tried to change to another simple radio module.

/***
 * Configure Sensor Network
 */
#define RF24_CHANNEL	   84             //RF channel for the sensor net, 0-127
#define RF24_DATARATE 	   RF24_250KBPS   //RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
#define RF24_PA_LEVEL 	   RF24_PA_MAX    //Sensor PA Level == RF24_PA_MIN=-18dBm, RF24_PA_LOW=-12dBm, RF24_PA_HIGH=-6dBM, and RF24_PA_MAX=0dBm
#define RF24_PA_LEVEL_GW   RF24_PA_MAX //RF24_PA_LOW  //Gateway PA Level, defaults to Sensor net PA Level.  Tune here if using an amplified nRF2401+ in your gateway.
#define BASE_RADIO_ID 	   ((uint64_t)0xA8A8E1FC00LL) // This is also act as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network.

But result is the same. Works great on breadboard. But fail on MYS board.

@hek how could i check the problem in GW radio ? Is it possible to fix?

Could you give me some advice? I`m new to mysensors so it will be great for me if you could help me

Hello,
Are everybody ok with 5v arduino and 662k on U1? My sensor node refuse to work.
But on the breadboard everything is ok.
It looks like the problem is in radio power. On breadboard i used 2 different step down convertor board, but both of them was on AMS1117 the power was 3.264 and 3.287.
And on MYS 662k give 3.324. I tried to use capacitors 4.7uF - 100uF, without result.
I also tried to change to another 662k from the pack. But it shows the same result.

Could you give me any suggestion ?
Thank you

send: 1-1-0-0 s=255,c=0,t=18,pt=0,l=5,st=fail:1.4.1
send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=14,st=fail:Relay & Button
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,st=fail:1.0
send: 1-1-0-0 s=1,c=0,t=3,pt=0,l=5,st=fail:1.4.1