Mr_sensor

Mr_sensor

Great! That helped a lot. I Kicked that out when reading the Converting a sketch from 1.5 to 2.x article.

4911 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.4
4954 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:50.2
4962 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
4968 MCO:SLP:TPD

Now I only have to find out what to use for mqtt to read this sensor values. Thats still not very clear to me:
Guess it would be something like:
mygateway1-out/2/2/0/0/ or 2/2/0/0/1 ?

Would it be possible to have something like this:

mygateway-out/2/2/Temperature ?

Mr_sensor

@sundberg84 Well I tried that but did not get the measurement straight from the pcb si I decided t solder a new board using the right capacitor this time (0,1uf instead of 1uf) made sure using the right resistors as well and adding a capacitor after the booster. Than with the same mini pro from the other board tested again and wow it is working as intended.

Child ID 2Battery Voltage: 3.44 V
Battery Percent: 102 %
2930 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:102
2938 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
2945 TSF:TDI:TSL
2947 MCO:SLP:WUP=-1
2949 TSF:TRI:TSB
3065 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
3178 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
957
Child ID 2Battery Voltage: 3.22 V
Battery Percent: 95 %
3690 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:95
3698 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
3704 TSF:TDI:TSL
3706 MCO:SLP:WUP=-1
3708 TSF:TRI:TSB
3815 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
3932 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
955
Child ID 2Battery Voltage: 3.21 V
Battery Percent: 95 %
4442 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
4452 TSF:TDI:TSL
4454 MCO:SLP:WUP=-1
4456 TSF:TRI:TSB
4560 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
4673 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
953
Child ID 2Battery Voltage: 3.21 V
Battery Percent: 95 %
5185 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
5193 TSF:TDI:TSL
5195 MCO:SLP:WUP=-1
5197 TSF:TRI:TSB
5304 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
5416 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
952
Child ID 2Battery Voltage: 3.20 V
Battery Percent: 95 %
5926 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
5935 TSF:TDI:TSL
5939 MCO:SLP:WUP=-1
5941 TSF:TRI:TSB
6045 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
6158 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
952
Child ID 2Battery Voltage: 3.20 V
Battery Percent: 95 %
6670 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
6678 TSF:TDI:TSL
6680 MCO:SLP:WUP=-1
6682 TSF:TRI:TSB
6789 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
6901 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
952
Child ID 2Battery Voltage: 3.20 V
Battery Percent: 95 %
7411 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
7419 TSF:TDI:TSL
7424 MCO:SLP:WUP=-1
7426 TSF:TRI:TSB
7530 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
7643 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
952
Child ID 2Battery Voltage: 3.20 V
Battery Percent: 95 %
8155 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
8163 TSF:TDI:TSL
8165 MCO:SLP:WUP=-1
8167 TSF:TRI:TSB
8273 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
8388 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
955
Child ID 2Battery Voltage: 3.21 V
Battery Percent: 95 %
8898 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
8908 TSF:TDI:TSL
8910 MCO:SLP:WUP=-1
8912 TSF:TRI:TSB
9021 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
9132 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
948
Child ID 2Battery Voltage: 3.19 V
Battery Percent: 94 %
9646 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:94
9654 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
9660 TSF:TDI:TSL
9662 MCO:SLP:WUP=-1
9664 TSF:TRI:TSB
9771 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
9881 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
952
Child ID 2Battery Voltage: 3.20 V
Battery Percent: 95 %
10395 TSF:MSG:SEND,2-2-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:95
10403 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
10409 TSF:TDI:TSL
10412 MCO:SLP:WUP=-1
10414 TSF:TRI:TSB
10520 TSF:MSG:SEND,2-2-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:998.0
T: 998.00
10635 TSF:MSG:SEND,2-2-0-0,s=0,c=1,t=1,pt=7,l=5,sg=0,ft=0,st=OK:998.0
H: 998.00
953
Child ID 2Battery Voltage: 3.21 V
Battery Percent: 95 %
11147 MCO:SLP:MS=60000,SMS=0,I1=255,M1=255,I2=255,M2=255
11155 TSF:TDI:TSL

Now in mqtt I can see the percentage as:

95
qos : 0, retain : false, cmd : publish, dup : false, topic : **mygateway1-out/2/255/3/0/0**, messageId : , length : 30, Raw payload : 5753```

But not the voltage?

Mr_sensor

@mfalkvidd said in What is loaded / running on the arduino?:

@mr_sensor you are correct that it is not possible to get the sketch from the Arduino.

But all MySensors sketches have something like this:
sendSketchInfo("TemperatureAndHumidity", "1.1");
which identifies which type of sketch and the version of that sketch, every time the sensor is restarted. If you store your sketches in some version control system (git is most popular), keeping track of them becomes quite easy.

See also https://forum.mysensors.org/topic/2203/method-to-reveal-sketch-inside-node-or-g-w for an earlier discussion on a similar topic.

@mfalkvidd thanks for the reply. The sendSketchInfo is indeed helpfull will also read the link.

Mr_sensor

I'm not sure if this is the right place to ask. But it seems right to me
Hi I have e few of the Easy/Newbie-pcb working for some time with good effort. One of them even in a shed at 20 - 25 meters in the garden which is fairly good isolated. Sending Temp/Hum/battery level. And the Gateway is in the house on the first floor behind a door in a wardrobe.

Now I have a second shed which is behind the fist shed. Also very good isolated. The pcb I have in there is not reaching the gateway (it did before until the battery was empty).
Can I have the pcb in the first shed also working as an extender, so the second pcb will be able to send out topics to the gateway as well? What to add to my code to achieve that?

Mr_sensor

@mfalkvidd said in What is loaded / running on the arduino?:

@mr_sensor you are correct that it is not possible to get the sketch from the Arduino.

But all MySensors sketches have something like this:
sendSketchInfo("TemperatureAndHumidity", "1.1");
which identifies which type of sketch and the version of that sketch, every time the sensor is restarted. If you store your sketches in some version control system (git is most popular), keeping track of them becomes quite easy.

See also https://forum.mysensors.org/topic/2203/method-to-reveal-sketch-inside-node-or-g-w for an earlier discussion on a similar topic.

@mfalkvidd thanks for the reply. The sendSketchInfo is indeed helpfull will also read the link.

Mr_sensor

Just a question that is on my mind for some time now. When a sketch is loaded on a arduino (in my case a pro mini) how to see / find out what is on that board? Or is that even not possible?
After some time running a node and building others in the mean time it is not always clear what is on the particular node. Dis I miss something basic here? Or is it just not possible getting the (sketch) info from the arduino?
How are you dealing with it. Having a sketch named/ numbered for every node? Just wondering what is the best practise.

Mr_sensor

@gohan

Well the NACKS are gone by setting the RF_24_PA_HIGH but still I do not get any temperature after the first one while starting up:

16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.2.0
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSM:INIT:STATID=4
38 TSF:SID:OK,ID=4
40 TSM:FPAR
43 TSM:FPAR:STATP=0
45 TSM:ID
47 TSM:ID:OK
47 TSM:UPL
1730 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=NACK:1
3739 TSM:UPL
5421 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=1,st=NACK:1
7430 TSM:UPL
7452 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=2,st=OK:1
7460 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
7467 TSF:MSG:PONG RECV,HP=1
7471 TSM:UPL:OK
7473 TSM:READY:ID=4,PAR=0,DIS=1
7491 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
7499 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
7512 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.2.0
7530 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
9545 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Temperature Sensor
9586 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.1
9801 TSF:MSG:SEND,4-4-0-0,s=1,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
9840 TSF:MSG:SEND,4-4-0-0,s=2,c=0,t=30,pt=0,l=0,sg=0,ft=0,st=OK:
9848 MCO:REG:REQ
9861 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
9869 TSF:MSG:READ,0-0-4,s=255,c=3,t=27,pt=1,l=1,sg=0:1
9875 MCO:PIM:NODE REG=1
9877 MCO:BGN:STP
9926 MCO:BGN:INIT OK,TSP=1
911
Child ID 2Battery Voltage: 3.06 V
Battery Percent: 91 %
10438 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:91
10446 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
10452 TSF:TDI:TSL
10455 MCO:SLP:WUP=-1
10457 TSF:TRI:TSB
831
Child ID 2Battery Voltage: 2.79 V
Battery Percent: 83 %
10967 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:83
10975 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
10981 TSF:TDI:TSL
10983 MCO:SLP:WUP=-1
10985 TSF:TRI:TSB
830
Child ID 2Battery Voltage: 2.79 V
Battery Percent: 83 %
11493 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
11501 TSF:TDI:TSL
11503 MCO:SLP:WUP=-1
11505 TSF:TRI:TSB
833
Child ID 2Battery Voltage: 2.80 V
Battery Percent: 83 %
12013 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
12021 TSF:TDI:TSL
12023 MCO:SLP:WUP=-1
12025 TSF:TRI:TSB
830
Child ID 2Battery Voltage: 2.79 V
Battery Percent: 83 %
12533 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
12541 TSF:TDI:TSL```

Mr_sensor

I have a newbie-pcb board with a Dallas temperature sensor attached. I mixed some sketches together to make it work.
When starting the sensor the first time I can see all the actions performed. Reading temperature and battery percentage. But than after sleeping it is only reading and sending battery percentage (no voltage)? No temperature action is visible any-more. So, there must be a fault in my sketch which makes it read the temperature part only once? Any advice on this? Thanks.

[code]

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0: Henrik EKblad
 * Version 1.1 - 2016-07-20: Converted to MySensors v2.0 and added various improvements - Torben Woltjen (mozzbozz)
 * 
 * DESCRIPTION
 * This sketch provides an example of how to implement a humidity/temperature
 * 
 * Dallas temperature sensor DS18B20
 *  
 * For more information, please visit:
 * http://www.mysensors.org/build/humidity
 * 
 HTU21D Humidity Sensor
 Hardware Connections (Breakoutboard to Arduino):
 -VCC = 3.3V
 -GND = GND
 -data  = D3 met pcb 470 uf resistor
 */

 
#define MY_NODE_ID 4
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC

// Enable debug prints
#define MY_DEBUG

// Enable and select radio type attached 
#define MY_RADIO_NRF24
//#define MY_RF24_PA_LEVEL RF24_PA_HIGH
//#define MY_RADIO_RFM69
//#define MY_RS485
 
#include <MySensors.h> 
//#include <Wire.h>
#include <SPI.h>
#include <OneWire.h>
#include <DallasTemperature.h>


// Force sending an update of the temperature after n sensor reads, so a controller showing the
// timestamp of the last update doesn't show something like 3 hours in the unlikely case, that
// the value didn't change since;
// i.e. the sensor would force sending an update every 
//UPDATE_INTERVAL*FORCE_UPDATE_N_READS [ms]
//static const uint8_t FORCE_UPDATE_N_READS = 10;

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No
// arrays to hold device address
DeviceAddress insideThermometer;

#define ONE_WIRE_BUS 3 // Pin where dallas sensor is connected 
#define MAX_ATTACHED_DS18B20 1
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 


float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
bool receivedConfig = true;
bool metric = true;

#define CHILD_ID_TEMP 1
#define CHILD_ID_BATTERY 2
#define CHILD_ID_VOLT 3
//#define CHILD_ID_PRCNT 3

float lastTemp;
//float lastHum;

uint8_t nNoUpdatesTemp;
//uint8_t nNoUpdatesHum;
//boolean metric = true;





void presentation()  
{ 
 // Send the Sketch Version Information to the Gateway                                                                                                                     
  sendSketchInfo("Temperature Sensor", "1.1");      
   
 // Register all sensors to gw (they will be created as child devices)                                                                                                     
//  present(CHILD_ID_HUM, S_HUM);                                                                                                                                          
  present(CHILD_ID_TEMP, S_TEMP);
   present(CHILD_ID_BATTERY, S_MULTIMETER);                                                                                                                                         
  metric = getControllerConfig().isMetric;

// Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
   
}

int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
                                                                                                                                                  
//unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)  60000                                                                                           
static int oldBatteryPcnt = 0;                                                                                                                                                                        
                                                                                                                                                               
                                                                                                                                                                        
//Create an instance of the object                                                                                                                                          

  MyMessage msg(0,V_TEMP);                                                                                                                                                                                                                                                                                                                           
//MyMessage msgHum(CHILD_ID_HUM, V_HUM);                                                                                                                                      
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);                                                                                                                                   
MyMessage msgBattery(CHILD_ID_BATTERY, V_VOLTAGE);
//MyMessage msgBattery(CHILD_ID_BATTERY, V_PRC);


void setup() {
    // Startup up the OneWire library
  sensors.begin();

     // use the 1.1 V internal reference
#if defined(__AVR_ATmega2560__)
    analogReference(INTERNAL1V1);
#else
    analogReference(INTERNAL);
#endif

// requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

} 
                                                                                                                                                                                                                                                                                                                                                 
void loop()                                                                                                                                                                 
{                                                                                                                                                                           


// Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }


// some delay here
  //delay(500);

   // get the battery Voltage
     
    int sensorValue = analogRead(BATTERY_SENSE_PIN);
    delay(500);
#ifdef MY_DEBUG
    Serial.println(sensorValue);
#endif

    // 1M, 470K divider across battery and using internal ADC ref of 1.1V
    // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
    // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
    // 3.44/1023 = Volts per bit = 0.003363075
    int batteryPcnt = sensorValue / 10;

#ifdef MY_DEBUG
    float batteryV  = sensorValue * 0.003363075;
    Serial.print("Child ID ");
    Serial.print(CHILD_ID_BATTERY);
    Serial.print("Battery Voltage: ");
    Serial.print(batteryV);
    Serial.println(" V");

    Serial.print("Battery Percent: ");
    Serial.print(batteryPcnt);
    Serial.println(" %");
#endif

    if (oldBatteryPcnt != batteryPcnt) {
        // Power up radio after sleep
              
        sendBatteryLevel(batteryPcnt);
        oldBatteryPcnt = batteryPcnt;
    } 
                                                                                                                                                                      
  sleep(SLEEP_TIME); //sleep a bit  
                                                                                                                                       
}
[/code]```


This is in the serial monitor:

[code]```
16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.2.0
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSM:INIT:STATID=4
38 TSF:SID:OK,ID=4
40 TSM:FPAR
43 TSM:FPAR:STATP=0
45 TSM:ID
47 TSM:ID:OK
47 TSM:UPL
1730 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=NACK:1
3739 TSM:UPL
5421 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=1,st=NACK:1
7430 TSM:UPL
7477 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=2,st=OK:1
7497 TSF:MSG:READ,0-0-4,s=255,c=3,t=25,pt=1,l=1,sg=0:1
7503 TSF:MSG:PONG RECV,HP=1
7507 TSM:UPL:OK
7510 TSM:READY:ID=4,PAR=0,DIS=1
7518 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
7526 TSF:MSG:READ,0-0-4,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
7536 TSF:MSG:SEND,4-4-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.2.0
7557 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
11247 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=NACK:Temperature Sensor
12939 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=1,st=NACK:1.1
14628 !TSF:MSG:SEND,4-4-0-0,s=1,c=0,t=6,pt=0,l=0,sg=0,ft=2,st=NACK:
16318 !TSF:MSG:SEND,4-4-0-0,s=2,c=0,t=30,pt=0,l=0,sg=0,ft=3,st=NACK:
16324 MCO:REG:REQ
18010 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=4,st=NACK:2
21698 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=5,st=NACK:2
21706 !TSM:READY:UPL FAIL,STATP
25389 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2
29079 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=NACK:2
31088 MCO:BGN:STP
31137 MCO:BGN:INIT OK,TSP=1
31141 MCO:SLP:MS=94,SMS=0,I1=255,M1=255,I2=255,M2=255
31148 TSF:TDI:TSL
31150 MCO:SLP:WUP=-1
31154 TSF:TRI:TSB
903
Child ID 2Battery Voltage: 3.04 V
Battery Percent: 90 %
31657 !TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=2,st=NACK:90
31668 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
31674 TSF:TDI:TSL
31676 MCO:SLP:WUP=-1
31678 TSF:TRI:TSB
31682 MCO:SLP:MS=94,SMS=0,I1=255,M1=255,I2=255,M2=255
31688 TSF:TDI:TSL
31690 MCO:SLP:WUP=-1
31692 TSF:TRI:TSB
831
Child ID 2Battery Voltage: 2.79 V
Battery Percent: 83 %
32202 TSF:MSG:SEND,4-4-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=3,st=OK:83
32208 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
32217 TSF:TDI:TSL```

Mr_sensor

@gohan said in Easy/Newbie PCB (RFM69 HW/W edition) for MySensors:

but this is RFM69 radio pcb not NRF24
I know but I am using the nrf24 pcb.

Do I need to add something like this when using the AP version?

#define MY_RADIO_NRF24

#define MY_RF24_PA_LEVEL RF24_PA_HIGH

Or just #define MY_RADIO_NRF24

Mr_sensor

@gohan Ok, what do you mean by "define HW" in code" ? This in my code:
#define MY_RADIO_NRF24

Mr_sensor

@mr_sensor said in Easy/Newbie PCB (RFM69 HW/W edition) for MySensors:

@sundberg84 @gohan Ok thanks for the input I will order some of the extended ones and see if thing s will improve.

The parts mentioned above arrived. I thought just swapping the radio's and see if there is any improvement. But it seems my devices are not happy with there new radio ? So are these new devices coming with the same pin-out and are they using the same library as the non amplified radio"s ? Or do I need to alter my sketches or wiring for it to work?

Mr_sensor

@sundberg84 @gohan Ok thanks for the input I will order some of the extended ones and see if thing s will improve.

Mr_sensor

@gohan said in Easy/Newbie PCB (RFM69 HW/W edition) for MySensors:

I would get better quality nrf24 modules and using a PA LNA one on the gateway may also help. Sure the rfm69 at 433MHz can have a better wall penetration, but I think you can do with better radios. Look for CDEByte store on aliexpress, they have good radio modules. Also a poor quality power supply can reduce the effective range.
If you want to try the RFM69 radios, you can "convert" the ones you have with this https://www.mysensors.org/hardware/nrf2rfm69

So these would be better?
https://nl.aliexpress.com/item/E01-ML01DP5-Ebyte-2-4GHz-20dBm-2100m-nRF24L01-SPI-Wireless-transceiver-module/32638720689.html?spm=a2g0s.13010208.99999999.336.T3AfNk
https://nl.aliexpress.com/item/CDEBYTE-2PCS-Lot-E01-ML01D-Wireless-Transceiver-For-Arduino-nRF24L01-2-4GHz-Antenna-Module-For-Microcontroll/32803704874.html?spm=a2g0s.13010208.99999999.333.T3AfNk
https://nl.aliexpress.com/item/CDEBYTE-2PCS-Lot-Special-promotions-1800-meter-long-distance-nRF24L01-PA-LNA-wireless-modules-with-PCB/32803720600.html?spm=a2g0s.13010208.99999999.330.T3AfNk

If I use one with PA_LNA on my Gateway are the pin-out the same as for the nrf24l+ as in the mysensors gatweay example?
Also there are models with nrf24l+PA what is the difference with the nrf24l+ ones?

Mr_sensor

@Mr_sensor

Best posts made by Mr_sensor

Latest posts made by Mr_sensor