Hi Niklas,
I know this is a very old post, but its worth a try. How did you get out the daily Kwh usage? As default my sensor only gives Watts and Kwh (accumulated from start), I have tried to run a Scene in Vera UI7 where there are a function in the sensor called resetKWh(), but it looks like it doesn't do anything. Any tips would be great, thanks.
Henning
Cool thanks! Then I will try when I have the gateway available.
@manutremo said in Problems with sensor node:
OP
Ok guys, thanks for all the tips so far. I checked again all wiring and tested the connection with a multimeter and yes, it looks like one of the "ready to use" cables was faulty. So I removed the crimp cables and soldered on wires and now it looks like it works at least. Now I only have the node connected to the PC (gateway is not available), so does this serial monitor print look correct? I have loaded some simple Door/window sensor sketch, why isn't the digital pin state show up in the serial monitor? Does it have to be connected to the gateway?
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
12 TSM:FPAR
15 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2022 !TSM:FPAR:NO REPLY
2024 TSM:FPAR
2026 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4034 !TSM:FPAR:NO REPLY
4036 TSM:FPAR
4038 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6046 !TSM:FPAR:NO REPLY
6048 TSM:FPAR
6050 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8058 !TSM:FPAR:FAIL
8059 TSM:FAIL:CNT=1
8061 TSM:FAIL:PDT
18065 TSM:FAIL:RE-INIT
18067 TSM:INIT
18074 TSM:INIT:TSP OK
18076 TSM:FPAR
18078 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20086 !TSM:FPAR:NO REPLY
20088 TSM:FPAR
20090 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
22099 !TSM:FPAR:NO REPLY
22102 TSM:FPAR
22104 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24112 !TSM:FPAR:NO REPLY
24114 TSM:FPAR
24116 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
26124 !TSM:FPAR:FAIL
26125 TSM:FAIL:CNT=2
26127 TSM:FAIL:PDT
36130 TSM:FAIL:RE-INIT
36132 TSM:INIT
36140 TSM:INIT:TSP OK
36142 TSM:FPAR
36144 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
38152 !TSM:FPAR:NO REPLY
38154 TSM:FPAR
38156 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
40164 !TSM:FPAR:NO REPLY
40166 TSM:FPAR
40168 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
42176 !TSM:FPAR:NO REPLY
42178 TSM:FPAR
42180 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
44188 !TSM:FPAR:FAIL
44189 TSM:FAIL:CNT=3
44191 TSM:FAIL:PDT
54194 TSM:FAIL:RE-INIT
54196 TSM:INIT
54203 TSM:INIT:TSP OK
54205 TSM:FPAR
54207 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
56215 !TSM:FPAR:NO REPLY
56217 TSM:FPAR
56219 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
58227 !TSM:FPAR:NO REPLY
58229 TSM:FPAR
58231 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
60239 !TSM:FPAR:NO REPLY
60241 TSM:FPAR
60243 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
62252 !TSM:FPAR:FAIL
62253 TSM:FAIL:CNT=4
62255 TSM:FAIL:PDT
72258 TSM:FAIL:RE-INIT
72260 TSM:INIT
72267 TSM:INIT:TSP OK
72269 TSM:FPAR
72271 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
74280 !TSM:FPAR:NO REPLY
74283 TSM:FPAR
74285 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
76293 !TSM:FPAR:NO REPLY
76295 TSM:FPAR
76297 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
78305 !TSM:FPAR:NO REPLY
78307 TSM:FPAR
78309 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
I bought from eBay, some from the UK and some from Germany. I will try to take a picture
Ok, Thanks for the tip, but I testes 3 different radios, even from two different sellers. Tips on where can I buy a good one?
Hi,
I'm trying to get my first sensor node to work, but the only thing that comes out of the serial monitor is this:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 !TSM:INIT:TSP FAIL
12 TSM:FAIL:CNT=1
14 TSM:FAIL:PDT
10016 TSM:FAIL:RE-INIT
10018 TSM:INIT
10024 !TSM:INIT:TSP FAIL
10028 TSM:FAIL:CNT=2
10029 TSM:FAIL:PDT
20032 TSM:FAIL:RE-INIT
20034 TSM:INIT
20040 !TSM:INIT:TSP FAIL
20043 TSM:FAIL:CNT=3
20044 TSM:FAIL:PDT
Can anyone tell me what this means?
I have check the wiring a million times, used different Aduino nanos (clones) and radio modules(nrf24), used decoupling capacitors and powered the radio from a different supply, but still the same 
Please give me some tips!
Ok, so I added more capacitors, but still the same printout in the serial monitor. Any more ideas?
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=1
0;255;3;0;9;TSM:FAIL:PDT
0;255;3;0;9;TSM:FAIL:RE-INIT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.1.1
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
0;255;3;0;9;!TSF:MSG:LEN,0!=7
0;255;3;0;9;TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:```Ok, Thanks for the tip. I will try this as soon as I have it available. Do you have any idea on value of the cap? 50uF , 100uF or more?
I added a 10uF to the radio, but I do not have more of them so i cannot try with more or one with a higher value. The 10uF dis not make any difference.