Hello everyone
This is my first post here so please be gentle with me.
Am trying to get a basic setup going using Nodemcu as a gateway and DHT22 running on an Arduino Nano.
Am no stranger to Arduino/Nodemcu programming etc, but what should I be seeing as an output from either the Sensor or the gateway? As far as I can tell, no debug statements are being sent but I do get some output.
Is there a walkthrough at all?
Thanks in advance.
Thank you Nca78.
The radio module has been connected up exactly as per the "Connecting the radio" page:
GND GND
3V3 VCC
D2 CE
D8 CSN/CS
D5 SCK
D7 MOSI
D6 MISO
I found the log parsing page after I posted and it was useful. Since then I have changed the cables for shorter duponts and used another nrf24l01 radio with the same result. What I haven't tried yet is the "add a capacitor to the power supply".
Would I be correct in thinking that according to the log file, the radio is being initialised and therefore appears to be wired correctly?
The capacitor thing is well documented, has anyone had to do this? If so, did it solve the issue?
The Arduino nano side of things is using one of those adapter boards with the built-in regulator so am thinking it may be a power issue?
And here is the output from the Nodemcu side:
0;255;3;0;9;TSF:LRT:OK
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
scandone
f 0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 4
cnt
chg_B1:-40
connected with xxxxxxxxxxxxxxx, channel 6
dhcp client start...
.ip:192.168.0.14,mask:255.255.255.0,gw:192.168.0.1
.IP: 192.168.0.14
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
pm open,type:2 0
Here is some output from the DHT22 board:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:FPAR
15 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2022 !TSM:FPAR:NO REPLY
2024 TSM:FPAR
2026 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4034 !TSM:FPAR:NO REPLY
4036 TSM:FPAR
4038 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6046 !TSM:FPAR:NO REPLY
6048 TSM:FPAR
6050 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8058 !TSM:FPAR:FAIL
8059 TSM:FAIL:CNT=1
8061 TSM:FAIL:PDT
18065 TSM:FAIL:RE-INIT
18067 TSM:INIT
18074 TSM:INIT:TSP OK
18076 TSM:FPAR
18078 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20086 !TSM:FPAR:NO REPLY
20088 TSM:FPAR
20090 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
22099 !TSM:FPAR:NO REPLY
22102 TSM:FPAR
22104 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24112 !TSM:FPAR:NO REPLY
24114 TSM:FPAR
24116 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
26124 !TSM:FPAR:FAIL
26125 TSM:FAIL:CNT=2
26127 TSM:FAIL:PDT
Thanks in advance again.
Hello everyone
This is my first post here so please be gentle with me.
Am trying to get a basic setup going using Nodemcu as a gateway and DHT22 running on an Arduino Nano.
Am no stranger to Arduino/Nodemcu programming etc, but what should I be seeing as an output from either the Sensor or the gateway? As far as I can tell, no debug statements are being sent but I do get some output.
Is there a walkthrough at all?
Thanks in advance.