@bobbybobbybobby

@pansen and @tbowmo fimaly i got arduino ide running on my rpi!!! i was trying this for about a weeks now.

thanks for the support.

@mfalkvidd

Great!! it works thanks for the fast reply

@mfalkvidd

Great!! it works thanks for the fast reply

Hi! can someone help me please

i have a problem.
when i try to contact the gateway in domoticz i get the folowing message:

2017-08-21 21:01:15.700 TCP: Reconnecting...
2017-08-21 21:01:16.700 MySensors: connected to: 10.0.1.20:5003
2017-08-21 21:01:25.701 MySensors: Connection reset!
2017-08-21 21:01:25.701 TCP: Reconnecting in 30 seconds...

i use the folowing sketch:

/**

• The MySensors Arduino library handles the wireless radio link and protocol
• between your home built sensors/actuators and HA controller of choice.
• The sensors forms a self healing radio network with optional repeaters. Each
• repeater and gateway builds a routing tables in EEPROM which keeps track of the
• network topology allowing messages to be routed to nodes.
• Created by Henrik Ekblad henrik.ekblad@mysensors.org
• Copyright (C) 2013-2015 Sensnology AB
• Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
• Documentation: http://www.mysensors.org
• Support Forum: http://forum.mysensors.org
• This program is free software; you can redistribute it and/or
• modify it under the terms of the GNU General Public License
• version 2 as published by the Free Software Foundation.

• REVISION HISTORY
• Version 1.0 - Henrik EKblad
• Contribution by a-lurker and Anticimex,
• Contribution by Norbert Truchsess norbert.truchsess@t-online.de
• Contribution by Tomas Hozza thozza@gmail.com
• DESCRIPTION
• The EthernetGateway sends data received from sensors to the ethernet link.
• The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
• The GW code is designed for Arduino 328p / 16MHz. ATmega168 does not have enough memory to run this program.
• LED purposes:
• • To use the feature, uncomment MY_DEFAULT_xxx_LED_PIN in the sketch below
• • RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
• • TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
• • ERR (red) - fast blink on error during transmission error or recieve crc error
• See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.

*/

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable gateway ethernet module type
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with
// radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
#define MY_SOFTSPI
#define MY_SOFT_SPI_SCK_PIN 14
#define MY_SOFT_SPI_MISO_PIN 16
#define MY_SOFT_SPI_MOSI_PIN 15
#endif

// When W5100 is connected we have to move CE/CSN pins for NRF radio
#ifndef MY_RF24_CE_PIN
#define MY_RF24_CE_PIN 5
#endif
#ifndef MY_RF24_CS_PIN
#define MY_RF24_CS_PIN 6
#endif

// Enable to UDP
//#define MY_USE_UDP

#define MY_IP_ADDRESS 10,0,1,20 // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003

// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 7 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 8 // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN 9 // Transmit led pin

#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensors.h>

void setup()
{
}

void loop()
{
}

when i use the serial monitor in arduino app i get:

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 10.0.1.20
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect

what do i do wrong?

@tbowmo

Thanks! It indeed was a wire problem..

hi i have a problem..

i run an rpi3 with domoticz i have a powerd usbhub connected to it.
i have an nano with nrf+ with antenna (solderd an 4,7 cap to it)

when i connect it all with dupond cables the gateway works. but now i solderit all to an prototyping board and now i get the error...

i tried connecting the nrf to an external power suply but still get this error..

what can i do?

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;!TSM:INIT:TSP FAIL
0;255;3;0;9;TSM:FAIL:CNT=1
0;255;3;0;9;TSM:FAIL:PDT
0;255;3;0;9;TSM:FAIL:RE-INIT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:INIT:TSP FAIL```

@bobbybobbybobby

@pansen and @tbowmo fimaly i got arduino ide running on my rpi!!! i was trying this for about a weeks now.

thanks for the support.

@bobbybobbybobby said in Problem with mysensor library on Arduino IDE Running on Raspi:

@pansen
And
@tbowmo

i think i got a little bit further.. but get an error..
pi@raspberrypi:~ $ cd arduino-1.8.1
pi@raspberrypi:~/arduino-1.8.1 $ ./arduino
/home/pi/arduino-1.8.1/java/bin/java: error while loading shared libraries: libjli.so: cannot open shared object file: No such file or directory

this time without dutch

@pansen
And
@tbowmo

Thanks for helping me! I really appreciate it! Sorry for not being clear in what I wrote.

@tbowmo i don't know mutch about command line so that's why I was looking further with the info about arm version and all.

@tbowmo

Thanks for your reply

i needed a little more info on how to instal ide on linux/arm on a RPI

so i found the how to on the folowing url:
http://duinorasp.hansotten.com/arduino-1-6-x-for-raspberry-pi-jessie/

but i now get an error..

root@raspberrypi:/home/pi# dpkg -i arduino-core_1.6.5_all.deb arduino_1.6.5_all.deb
dpkg: fout bij verwerken van archief arduino-core_1.6.5_all.deb (--install):
krijg geen toegang tot archief: Bestand of map bestaat niet
dpkg: fout bij verwerken van archief arduino_1.6.5_all.deb (--install):
krijg geen toegang tot archief: Bestand of map bestaat niet
Fouten gevonden tijdens verwerken van:
arduino-core_1.6.5_all.deb
arduino_1.6.5_all.deb
root@raspberrypi:/home/pi#

what do i do wrong?