Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

How to change Radio ID on Raspberry Pi Gateway with RFM 69

Stefan_NE last edited by

Hello,
does anybody know how to change the Radio ID on Raspberry Pi Gateway with RFM 69

Have a nice day Stefan
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by mfalkvidd @Stefan_NE
@Stefan_NE set MY_RFM69_NETWORKID (documentation)

Instruction on how to use defines for the rpi gateway:
https://www.mysensors.org/build/raspberry#advanced

So something like
```
--extra-cxxflags="-DMY_RFM69_NETWORKID=\(110\)
```
Reply Quote 0
1 Reply Last reply
Stefan_NE last edited by

Thanks, works.
I hope the Pi gateway ist more stable than the ESP gateways . It will be a lot of work to move alle sensors to the new RFM69 driver
Reply Quote 1
1 Reply Last reply

3
Posts

26
Views

Log in to reply

Suggested Topics

SmartSleep a feature of the Gateway
Feature Requests • gateway openhab smartsleep • • strangeoptics

3

0
Votes

3
Posts

1881
Views

Nice. Didn't know that. But still it would be a great feature for the gateway to give every one the feature of smartSleep despite the controller.
MySensors gateway running as a service
Development • gateway • • OldSurferDude

4

0
Votes

4
Posts

22
Views

@mfalkvidd Thanks, I didn't see that! OSD
RFM69HW antenna
General Discussion • gateway pcb rfm69hw antenna • • tsunami

10

0
Votes

10
Posts

1020
Views

@tsunami My setup is max 50m radius and 433MHz standard power RFM69s so a small 1/4 wave whip works reliably even from a below ground pump chamber 10m away. Your 915MHz at 200m SHOULD work on 1/4 wave if obstacle free line of sight, but you could try a 2.4GHz Wifi router at one location and use a mobile at the other to test if you can see the router. I can see at least 3 neighbouring routers identified on my mobile from over 40m away through masonry, 10 on the laptop, so it's a simple enough test. If you can see the router on either, 915MHz should be rock solid with a simple whip and no need of directional antenna.
Newbie question about how the mysensors gateway connects to controller
General Discussion • gateway serial gateway ethernet gateway • • Thomas433

3

0
Votes

3
Posts

39
Views

@Boots33 Thanks a lot for the quick response. I now have my Nano running as a serial gateway and it is connected via a USB cable directly to my controller (Raspberry Pi 4 running Home Assistant / Hass.io). I added a local motion sensor to the Nano gateway HW and pasted the mysensors MotionSensor example code to the setup(), presentation() and loop() functions as well as to the definitions in the top of the GatewaySerial example code. I disabled the radio definitions as I currently have no radio capability in my gateway (not sure if this was necessary). In Home Assistant / Hass.io I updated the configuration.yaml with the following text (as described on the Home Assistant integration help): mysensors: gateways: - device: '/dev/ttyUSB0' And it works In Home Assistant Developer Tools under States I can now see my motion sensor go on and off by the flick of my hand. I had expected a bit more bumps on the road just to get this far, but wow - I am obviously walking in the foot prints of people who have worked hard to make it easy for the rest of us. I am sure I will hit bumps on the way when the radios have to send results to the gateway (thick concrete walls with lots of steel), but for now I will enjoy this big success. Thanks again Boots33
💬 RS485 Ethernet Gateway
OpenHardware.io • gateway ethernet rs485 mysensors gateway sensor network • • openhardware.io

5

0
Votes

5
Posts

1084
Views

@kimot No, it is an obvious mistake, I am very sorry. Maybe it is becouse the code in master branch is very old, the newest is not yet on github, but the developement branch is quite new. I am going to fix this soon.
💬 MySRaspiGW - MySensors Raspberry Pi GPIO Gateway
OpenHardware.io • gateway nrf24l01 raspberry smd gpio • • openhardware.io

11

0
Votes

11
Posts

3678
Views

Okay, finally got the original nrf24l01 SMD modules with the square chip visible... As exptected, things work just fine now, so the culprit of my issues was really the incompatible/fake "nrf24l01" SMD modules with the epoxy blob. If you want to use normal nrf24l01+ modules together with this smd gateway, DO NOT USE the smd module with the epoxy blob, as they won't work. Using only the fake SMD modules might work, too, but mixing the fake modules with real ones does not work.
Connect sensors directly to the Gateway (again)
Development • gateway sensor development • • mortommy

22

0
Votes

22
Posts

14535
Views

@Tmaster You give each sensor a child id (0-254) in the node.
RPI Gateway Error
Hardware • gateway • • hakha4

5

0
Votes

5
Posts

76
Views

Hi! Thank's for info. I had almost given up and now using an ESP GW instead but I'll give your setup a try

0
Online

11.3k
Users

11.1k
Topics

112.5k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1