I've had a Vera 3 for some time but I am new to the Arduino world and was trying to get a Moteino USB to act as my Vera plug-in gateway. The Moteino has no sensors on it. From what i can tell, the Vera refuses to allow my access to the USB port.
I have the plugin files uploaded to Vera, a device is created (with Luuap startup failure). In advanced, the com failure is (1)
and Vera insists I choose a serial port. Been through the Vera serial port dance, unplug wait for reload, etc. But, no luck.
I've stayed up till the wee hours for enough nights trying to get this to work that my wife thinks I have a girlfriend named "Vera" .I would really appreciate some guidance with how to proceed.
Here is the gateway sketch from the Vera plugin page:
/**
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2015 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*******************************
*
* DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on radio network.
*
* The GW code is designed for Arduino Nano 328p / 16MHz
*
* Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
*
* LEDs (OPTIONAL):
* - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error
*
*/
// Enable debug prints to serial monitor
#define MY_DEBUG
// Enable and select radio type attached
// #define MY_RADIO_NRF24
#define MY_RADIO_RFM69
// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
// #define MY_RF24_PA_LEVEL RF24_PA_LOW
// Enable serial gateway
#define MY_GATEWAY_SERIAL
// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
#define MY_BAUD_RATE 115200
#endif
// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED
#include <MySensors.h>
void setup()
{
// Setup locally attached sensors
}
void presentation()
{
// Present locally attached sensors
}
void loop()
{
// Send locally attached sensor data here
}
Here is some info about the Vera serial ports from a putty session.
root@MiOS_30011150:~# ls [Jusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0001
Bus 002 Device 003: ID 0403:6015
root@MiOS_30011150:~# dmesg | grep tty*
Kernel command line: console=ttyS1,57600 board=NA900 rootfstype=squashfs,jffs2
console [ttyS1] enabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
ra_nand_probe: alloc 7f8, at 87841000 , btt(878415f8, 200), mtd:87841000
eth0: AR8236 switch driver attached.
rtc-s35390a 0-0030: setting system clock to 2017-03-23 14:54:59 UTC (1490280899)
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.4.4
JFFS2 notice: (483) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 6 of xref (0 dead, 0 orphan) found.
root@MiOS_30011150:~# dmesg dmesg > /tmp/dmesg-pre
root@MiOS_30011150:~# dmesg > /tmp/dmesg-post
root@MiOS_30011150:~# diff -u /tmp/dmesg-pre /tmp/dmesg-post
--- /tmp/dmesg-pre
+++ /tmp/dmesg-post
@@ -196,3 +196,4 @@
usb 2-2: USB disconnect, address 3
usb 2-2: new full speed USB device using rt3883-ohci and address 4
usb 2-2: USB disconnect, address 4
+usb 2-2: new full speed USB device using rt3883-ohci and address 5
root@MiOS_30011150:~# tail -f /var/log/cmh/LuaUPnP.log | grep Arduino
29822 root 1672 S grep Arduino
29822 root 1672 S grep Arduino
29822 root 1672 S grep Arduino
10 03/23/17 12:23:08.423 Device_LuaUPnP::LoadDeviceDoc 78 file D_Arduino1.xml size 1034 result 0 <0x2ab21000>
10 03/23/17 12:23:08.423 Device_LuaUPnP::LoadDeviceDoc 78 file /etc/cmh-ludl//D_Arduino1.xml finished <0x2ab21000>
25 03/23/17 12:23:09.287 JobHandler_LuaUPnP::ParseAllImplementations parsed I_Arduino1.xml <0x2ab21000>
10 03/23/17 12:23:09.294 Device_LuaUPnP::MatchupImplementations device 78 using implementation: I_Arduino1.xml with 9 services <0x2ab21000>
luup.log("Arduino plugin: loading library L_Arduino ...")
package.loaded.L_Arduino = nil
p = require("L_Arduino")
if (package.loaded.L_Arduino == nil)
luup.log("Arduino plugin: plugin is not installed correctly. Library L_Arduino cannot be loaded.", 1)
luup.task("Plugin not correctly installed", 2, "Arduino plugin", -1)
luup.log("Arduino plugin: library L_Arduino loaded")
function SArduino_arduino1_SendCommand_job(lul_device,lul_settings,lul_job)
function SArduino_arduino1_SetUnit_job(lul_device,lul_settings,lul_job)
function SArduino_arduino1_StartInclusion_job(lul_device,lul_settings,lul_job)
function SArduino_arduino1_StopInclusion_job(lul_device,lul_settings,lul_job)
25 03/23/17 12:23:18.575 LuImplementation::StartLua device: 78 file:I_Arduino1.xml startup:startup pLuaInterface: 0xa29bb0 ip: port 0 protocol: (null) <0x2b455680>
25 03/23/17 12:23:18.576 LuImplementation::StartLua running startup code for 78 I_Arduino1.xml <0x2b455680>
50 03/23/17 12:23:18.576 luup_log:78: Arduino plugin: loading library L_Arduino ... <0x2b455680>
50 03/23/17 12:23:18.617 luup_log:78: Arduino plugin: library L_Arduino loaded __LEAK__ this:16384 start:2224128 to 0xd13000 <0x2b455680>
50 03/23/17 12:23:18.618 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduino1,PluginVersion, 1.5, 78 <0x2b455680>
50 03/23/17 12:23:18.618 luup_log:78: Arduino: Trying for a serial connection <0x2b455680>
01 03/23/17 12:23:18.619 [31;1mluup_log:78: Arduino: Serial port not connected. First choose the serial port and restart the lua engine.[0m <0x2b455680>
01 03/23/17 12:23:18.619 [31;1mluup_log:78: Arduino: Choose the Serial Port[0m <0x2b455680>
01 03/23/17 12:23:18.635 [31;1mLuImplementation::StartLua running startup code for 78 I_Arduino1.xml failed[0m <0x2b455680>
