Dear all,

I am trying to use the ESP8266 with a local attached relay , but it is not recognized by domoticz.
Can someone help on that ?

Here the information log and the ino code:

DOMOTICZ LOG

2016-01-17 13:49:54.731 MySensors: connected to: 192.168.1.111:5003 
2016-01-17 13:49:54.731 MySensors: Gateway Ready... 
2016-01-17 13:49:55.781 MySensors: Gateway Version: 1.6.0-beta 
2016-01-17 13:49:55.781 MySensors: Gateway Version: 1.6.0-beta 

ESP LOG

connected with FCSSID, channel 1
ip:192.168.1.111,mask:255.255.255.0,gw:192.168.1.1
.IP: 192.168.1.111
start call Setup
Start wait
End wait
End call Setup
start call presentation
Start wait
End wait
End call presentation
0;0;3;0;9;Init complete, id=0, parent=0, distance=0
0;0;3;0;9;Client 0 connected
0;0;3;0;9;Client 0: 0;0;3;0;2;
0;0;3;0;9;Client 0: 0;0;3;0;2;Get Version
0;0;3;0;9;Client 0: 0;0;3;0;18;PING
0;0;3;0;9;Client 0: 0;0;3;0;18;PING
0;0;3;0;9;Client 0: 0;0;3;0;18;PING
0;0;3;0;9;Client 0: 0;0;3;0;18;PING
0;0;3;0;9;Client 0: 0;0;3;0;18;PING

INO code:

#include <EEPROM.h>
#include <SPI.h>

// Enable debug prints to serial monitor
#define MY_DEBUG 
//#define MY_REPEATER_FEATURE
#define MY_DEBUG_VERBOSE

// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600

// Enables and select radio type (if attached)
// #define MY_RADIO_NRF24
// #define MY_RADIO_RFM69

// Gateway mode always enabled for ESP8266. But we add this anyway ;)
#define MY_GATEWAY_ESP8266

#define MY_ESP8266_SSID "FCSSID"
#define MY_ESP8266_PASSWORD "jfsc20100930*"

// Enable UDP communication
//#define MY_USE_UDP

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
#define MY_IP_ADDRESS 192,168,1,111

// If using static ip you need to define Gateway and Subnet address as well
#define MY_IP_GATEWAY_ADDRESS 192,168,1,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0

// The port to keep open on node server mode 
#define MY_PORT 5003      

// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68

/*
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED

*/

#if defined(MY_USE_UDP)
  #include <WiFiUDP.h>
#else
  #include <ESP8266WiFi.h>
#endif

// Enable repeater functionality for this node
//#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensor.h>

#define RELAY_1  4  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay


void setup()  
{ 


  Serial.println("start call Setup");
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
    // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
    Serial.println("Start wait");  
    //delay(60000);  
    Serial.println("End wait");  
    Serial.println("End call Setup");
}

void presentation()  
{   

    Serial.println("start call presentation");
    Serial.println("Start wait");  
    //delay(60000);  
    Serial.println("End wait");  
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay2", "2.0");

  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_LIGHT);
  }

      Serial.println("End call presentation");
}


void loop() 
{
      //Serial.println("start call loop");
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}