hakha4

hakha4

Hi
Thank's for answer. RF24 isn't a wifi radio, work's like RFM I believe.
I'm building a Mysensors gateway with lan for Domoticz and as I said with Esp8266 it works and I've used the example sketch for Esp32 GW so I must made some fault. I'll try and error but if someone have tips I appreciate comment's

hakha4

Hi
I'm trying to get a gateway with ESP32 devkit V1.0 to work. I have an ESP8266 GW working but want some extra pins for traffic light to work and perhaps better speed etc.
I found a pinout in 'MyHWESP32.h' as below but I always get confused refeering to pin number. I assume the numbers refeers to GPIO number ?. I use an adapter for the radio to get extra juice and power the adapter from the Vin pin (5V from USB) but I can't get radio to work.
Checked and rechecked wiring.

Output from serial port :
10040 TSM:FAIL:RE-INIT
10041 TSM:INIT
10048 !TSM:INIT:TSP FAIL
10050 TSM:FAIL:CNT=2
10052 TSM:FAIL:DIS
10053 TSF:TDI:TSL
20056 TSM:FAIL:RE-INIT
20057 TSM:INIT
20064 !TSM:INIT:TSP FAIL
20066 TSM:FAIL:CNT=3
20068 TSM:FAIL:DIS
20069 TSF:TDI:TSL
Adapter used :

Code :

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2018 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - tekka
 *
 * DESCRIPTION
 * The ESP32 gateway sends data received from sensors to the WiFi link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 * ----------- PINOUT --------------
 * | IO   | RF24 | RFM69 | RFM95 |
  |------|------|-------|-------|
  | MOSI | 23   | 23    | 23    |
  | MISO | 19   | 19    | 19    |
  | SCK  | 18   | 18    | 18    |
  | CSN  | 5    | 5     | 5     |
  | CE   | 17   | -     | -     |
  | RST  | -    | 17    | 17    |
  | IRQ  | 16*  | 16    | 16    |
    
 * Make sure to fill in your ssid and WiFi password below.
 
   
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enables and select radio type (if attached)
#define MY_RADIO_RF24
//#define MY_RADIO_RFM69
//#define MY_RADIO_RFM95

#define MY_GATEWAY_ESP32

#define MY_WIFI_SSID "xxxxxxx"
#define MY_WIFI_PASSWORD "xxxxxxxx"

// Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static.
#define MY_HOSTNAME "ESP32_GW"

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
#define MY_IP_ADDRESS 192,168,1,10

// If using static ip you can define Gateway and Subnet address as well
#define MY_IP_GATEWAY_ADDRESS 192,168,1,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0

// The port to keep open on node server mode
#define MY_PORT 5003

// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2

#include <MySensors.h>

void setup()
{
	// Setup locally attached sensors
}

void presentation()
{
	// Present locally attached sensors here
}

void loop()
{
	// Send locally attached sensors data here
}

Anyone succesfully get the ESP32 to work ? Any idea what could be the problem ? Can someone confirm that pin numbers are correct ?
Any help appreciated

hakha4

You're absolutely right. Should be MyMessage msgC(SSR_C_ID, V_STATUS);
Sometimes you get blind when looking for typos. Thank's

hakha4

I'll try put in a delay and get back if not solved. Thank's

hakha4

Thankäs for answer. I've find code on internet with two relay's 'A and B'. Just added a third relay 'C'. When first using two relays everything worked ok with two child's registered in Domoticz but when updating the node with relay 'C it don't shows up in Domoticz. So my main question is if gateway recognize changes in an earlier reg. node or if you have to delete some info for a fresh reg. ? I've checked code for typo error but can't see any obvious errors. See code below:

/*
 * NANO:
 * Radio occupies pin 2,9-13
 * 
 */





#define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_ON 1
#define RELAY_OFF 0

#define SSR_A_ID 1   // Id of the sensor child pump filter
#define SSR_B_ID 2   // Id of the sensor child pump waterfall
#define SSR_C_ID 3   // Id of the sensor child pump waterfall

const int buttonPinA = 3;
const int buttonPinB = 7;
const int buttonPinC = 8;
const int relayPinA = 4; 
const int relayPinB = 5;
const int relayPinC = 6;
int oldValueA = 0;
int oldValueB = 0;
int oldValueC = 0;
bool stateA = false;
bool stateB = false;
bool stateC = false;


Bounce debouncerA = Bounce();
Bounce debouncerB = Bounce();
Bounce debouncerC = Bounce();

MyMessage msgA(SSR_A_ID, V_STATUS);
MyMessage msgB(SSR_B_ID, V_STATUS);
MyMessage msgC(SSR_B_ID, V_STATUS);

void setup()
{

  pinMode(buttonPinA, INPUT_PULLUP); // Setup the button Activate internal pull-up
  pinMode(buttonPinB, INPUT_PULLUP); // Setup the button Activate internal pull-up
  pinMode(buttonPinC, INPUT_PULLUP); // Setup the button Activate internal pull-up

// Then set relay pins in output mode
  pinMode(relayPinA, OUTPUT);
  pinMode(relayPinB, OUTPUT);
 pinMode(relayPinC, OUTPUT);
  // After setting up the buttons, setup debouncer
  debouncerA.attach(buttonPinA);
  debouncerA.interval(5);
  debouncerB.attach(buttonPinB);
  debouncerB.interval(5);
  debouncerC.attach(buttonPinC);
  debouncerC.interval(5);
  // Make sure relays are off when starting up
  digitalWrite(relayPinA, RELAY_OFF);
  digitalWrite(relayPinB, RELAY_OFF);
   digitalWrite(relayPinC, RELAY_OFF);

    /*--------------------- Added these lines for toggle switch-------------------------*/
  oldValueA = digitalRead(buttonPinA);  // set oldValueA to the current status of the toggle switch
  oldValueB = digitalRead(buttonPinB);  // set oldValueB to the current status of the toggle switch
  oldValueC = digitalRead(buttonPinC);  // set oldValueB to the current status of the toggle switch

  send(msgA.set(false)); // Send off state for relayA to ensure controller knows the switch is off
  send(msgB.set(false)); // Send off state for relayB to ensure controller knows the switch is off
  send(msgC.set(false)); // Send off state for relayB to ensure controller knows the switch is off

}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Pond Controller", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(SSR_A_ID, S_LIGHT);
  present(SSR_B_ID, S_LIGHT);
  present(SSR_C_ID, S_LIGHT);
}

/*
   Example on how to asynchronously check for new messages from gw
*/
void loop()
{
  debouncerA.update();
  // Get the update value
  int valueA = debouncerA.read();
  if (valueA != oldValueA) {
    send(msgA.set(stateA ? false : true), true); // Send new state and request ack back
  oldValueA = valueA;
  }
 

  debouncerB.update();
  // Get the update value
  int valueB = debouncerB.read();
  if (valueB != oldValueB) {
    send(msgB.set(stateB ? false : true), true); // Send new state and request ack back
  oldValueB = valueB;
  }

  debouncerC.update();
  // Get the update value
  int valueC = debouncerC.read();
  if (valueC != oldValueC) {
    send(msgC.set(stateC ? false : true), true); // Send new state and request ack back
  oldValueC = valueC;
  }
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_STATUS) {
      
    switch (message.sensor) {
      case 1:
        stateA = message.getBool();
        digitalWrite(message.sensor + 4, stateA ? RELAY_ON : RELAY_OFF);
        
        break;
      case 2:
        stateB = message.getBool();
        digitalWrite(message.sensor + 4, stateB ? RELAY_ON : RELAY_OFF);

        case 3:
        stateC = message.getBool();
        digitalWrite(message.sensor + 4, stateC ? RELAY_ON : RELAY_OFF);

        break;
      
    }
   
      // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.println(message.sensor);
    Serial.print("from node:");
    Serial.println(message.sender);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}

Regards

hakha4

I'm new to Mysensors but must say that I'm impressed sofar! Great job from the developers. I've made a gateway with ESP8266 that work's just fine. Now to my issue. Made a node with two relays and it show's up as expected in Domoticz and seems to work perfect. When upgrading the node by adding another relay it don't shows the added relay. What do I have to do for gateway to see that a node has changed ?
Any help appreciated
Regards

hakha4

@hakha4

Posts made by hakha4