Hi, It worked. using the 2.2 library solved my issue. Now I'll setup openhab. thanks for your quick and effective answer

Ok, I'll try that.
Are you refering to the mySensors library, right?

Hi gohan.
Sorry If I did not explain correctly. I upgraded to OpenHab 2.1.0
I was previously using RaspberryPi with OpenHab 1.8 + MQTT gateway.

Now I switched to a VM with Debian and OpenHab 2.1.0. and as I read that the MQTT gateway was not working with OH2.1 I flashed my gateway as an ethernet gw.

Regarding the logs.
I turned off the OpenHab machine and the gateway still repeats the output. Is it possible that the gateway is continuosly restarting?

Hi Friends, I started upgrading my system to Openhab2
I was using Openhab 1.8 with a MQTT gateway working fine. Now with same hardware I flashed the gateway to be Ethernet gateway, but I'm not able to make it work. I think the Gateway is not connecting with Openhab

In Openhab is always in offline state and if I disable startup check it appears as online but Opebhab debug shows like connections retries.

This is console output from my gateway

0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;Eth: connect
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.1.1
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSF:WUR:MS=0
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;MCO:REG:NOT NEEDED
IP: 192.168.88.205
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,TSP=1

and this is the DEBUG output from Openhab

21:01:31.744 [DEBUG] [ensors.factory.MySensorsCacheFactory] - Writing on cache given_ids, content: []
21:01:31.744 [ERROR] [al.protocol.ip.MySensorsIpConnection] - Failed connecting to bridge...next retry in 10 seconds (Retry No.:44)
21:01:31.744 [DEBUG] [al.protocol.ip.MySensorsIpConnection] - Disconnecting from IP bridge ...
21:01:31.745 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Stopping Writer thread
21:01:31.753 [WARN ] [rsAbstractConnection$MySensorsWriter] - Interrupted MySensorsWriter
21:01:31.759 [DEBUG] [rsAbstractConnection$MySensorsReader] - Stopping Reader thread
21:01:31.762 [WARN ] [rsAbstractConnection$MySensorsReader] - Interrupted MySensorsReader
21:01:31.767 [DEBUG] [ensors.factory.MySensorsCacheFactory] - Writing on cache given_ids, content: []
21:01:41.770 [DEBUG] [al.protocol.ip.MySensorsIpConnection] - Connecting to IP bridge [192.168.88.205:5003]
21:01:41.777 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 0;0;3;0;2;
21:01:42.774 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 0;0;3;0;2;
21:01:43.775 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 0;0;3;0;2;
21:01:44.775 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 0;0;3;0;2;
21:01:45.775 [DEBUG] [rsAbstractConnection$MySensorsWriter] - Sending to MySensors: 0;0;3;0;2;
21:01:46.775 [ERROR] [al.protocol.ip.MySensorsIpConnection] - Cannot start reading/writing thread, probably sync message (I_VERSION) not received. Try set skipStartupCheck to true

Any Ideas

Any help will be appreciated.

Hi.
When I use MQTTFx to see that the gateway is asking to OpenHab I see this.

MyMQTT/25/255/V_SKETCH_NAME
RTC Clock

MyMQTT/25/255/V_SKETCH_VERSION
1.0

MyMQTT/25/255/V_
(no data)

I saw in the library API that the time request is an internal command, maybe I´m wrong, but shouldn´t I expect a I_TIME instead

Does anyone know how to respond to this request?

Thank you.

Hi, I´m planning using request time to display some info and current date time
But I can get response from gateway about requestTime

I´m using MQTT gateway with OpenHab

Should I do something on Openhab?

Hi, did you find a solution for this. same conditions as you.
OpenHab + MQTT gw

I can´t get time from the controller.

Hi my name is Matias, I´m addicted to this website. I´m building my sensor network and now getting this common error.

I have MQTT Gateway with OpenHab as controller

MySensor vesion is 1.5 and using Arduino 1.6.5

Working on the same room, gateway and 2 sensors are not talking as they should. I´m getting ST=Fail

Here is the Log of one of my Sensors

send: 21-21-0-0 s=255,c=0,t=18,pt=0,l=3,sg=0,st=fail:1.5
send: 21-21-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=fail:0
repeater started, id=21, parent=0, distance=1
send: 21-21-0-0 s=255,c=3,t=11,pt=0,l=16,sg=0,st=fail:Relay + Humidity
send: 21-21-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=fail:1.1
send: 21-21-0-0 s=0,c=0,t=7,pt=0,l=0,sg=0,st=fail:
send: 21-21-0-0 s=1,c=0,t=6,pt=0,l=0,sg=0,st=fail:
find parent
send: 21-21-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,st=bc:
send: 21-21-0-0 s=1,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 21-21-0-0 s=2,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 21-21-0-0 s=3,c=0,t=3,pt=0,l=0,sg=0,st=fail:
send: 21-21-0-0 s=4,c=0,t=3,pt=0,l=0,sg=0,st=fail:

Here is my gateway debug

0;0;3;0;9;gateway started, id=0, parent=0, distance=0
Ok!
<<10 12 00 06 4D 51 49 73 64 70 03 02 00 3C 00 04 4D 51 54 54

20 02 00 00
<<82 17 00 E2 00 12 4D 79 4D 51 54 54 2F 32 30 2F 31 2F 56 5F 54 45 4D 50 00

90 03 00 E2 00
MyMQTT/20/1/V_TEMP
0;0;3;0;9;send: 0-0-20-20 s=1,c=1,t=0,pt=0,l=0,sg=0,st=fail:
<<82 16 00 E3 00 11 4D 79 4D 51 54 54 2F 32 30 2F 30 2F 56 5F 48 55 4D 00

90 03 00 E3 00
MyMQTT/20/0/V_HUM
0;0;3;0;9;send: 0-0-20-20 s=0,c=1,t=1,pt=0,l=0,sg=0,st=fail:
<<82 17 00 E4 00 12 4D 79 4D 51 54 54 2F 32 31 2F 31 2F 56 5F 54 45 4D 50 00

90 03 00 E4 00
MyMQTT/21/1/V_TEMP
0;0;3;0;9;send: 0-0-21-21 s=1,c=1,t=0,pt=0,l=0,sg=0,st=fail:
<<82 16 00 E5 00 11 4D 79 4D 51 54 54 2F 32 31 2F 30 2F 56 5F 48 55 4D 00

90 03 00 E5 00
MyMQTT/21/0/V_HUM
0;0;3;0;9;send: 0-0-21-21 s=0,c=1,t=1,pt=0,l=0,sg=0,st=fail:
0;0;3;0;9;read: 21-21-0 s=0,c=1,t=1,pt=7,l=5,sg=0:39.0
MyMQTT/21/0/V_HUM

30 17 00 11 4D 79 4D 51 54 54 2F 32 31 2F 30 2F 56 5F 48 55 4D 33 39 2E 30
0;0;3;0;9;read: 21-21-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
0;0;3;0;9;send: 0-0-21-21 s=255,c=3,t=8,pt=1,l=1,sg=0,st=fail:0

and this is what happended on my gateway when I send a command from OpenHab
MyMQTT/21/2/V_LIGHT
0;0;3;0;9;send: 0-0-21-21 s=2,c=1,t=2,pt=0,l=1,sg=0,st=fail:1

Sensor does not get any message

The 3 radios have the 4.7uF 35v capacitor.
The Gateway has a 3.3 voltage regulator,
I´m using 3 identical 3.3v 8 Mhz Arduino pro mini

I don´t know what else to check.

Hope you can help me.
Thank you very much.