Hi,

I'm having my first bash at mysensors and a total newbie to all of this so please excuse any simple oversights. I feel a bit sheepish just posting this as there are a few examples of what I am trying to do but after a day of head scratching i feel i need to ask for help.

The story so far:

I have a bunch of nodemcu's lying around so thought I would make some multi purpose wifi/ mqtt sensors.

First up I mashed the mqtt gateway and DHT sketches together.

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 *
 * DESCRIPTION
 * The ESP8266 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
 * The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
 *
 * LED purposes:
 * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
 * nRF24L01+  ESP8266
 * VCC        VCC
 * CE         GPIO4
 * CSN/CS     GPIO15
 * SCK        GPIO14
 * MISO       GPIO12
 * MOSI       GPIO13
 *
 * Not all ESP8266 modules have all pins available on their external interface.
 * This code has been tested on an ESP-12 module.
 * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
 * - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch')
 * - Connect GPIO15 via 10K pulldown resistor to GND
 * - Connect CH_PD via 10K resistor to VCC
 * - Connect GPIO2 via 10K resistor to VCC
 * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
 *
  * Inclusion mode button:
 * - Connect GPIO5 via switch to GND ('inclusion switch')
 *
 * Hardware SHA204 signing is currently not supported!
 *
 * Make sure to fill in your ssid and WiFi password below for ssid & pass.
 */


// Enable debug prints to serial monitor
#define MY_DEBUG

// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600

// Enables and select radio type (if attached)
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_GATEWAY_MQTT_CLIENT
#define MY_GATEWAY_ESP8266

// Set this node's subscribe and publish topic prefix
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"

// Set MQTT client id
#define MY_MQTT_CLIENT_ID "mysensors-1"

// Enable these if your MQTT broker requires usenrame/password
//#define MY_MQTT_USER "XXXXXXXXXXXXXXXX"
//#define MY_MQTT_PASSWORD "XXXXXXXXXXXXXXXX"

// Set WIFI SSID and password
#define MY_ESP8266_SSID "XXXXXXXXXXXXXXX"
#define MY_ESP8266_PASSWORD "XXXXXXXXXXX"

// Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static.
// #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway"

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
//#define MY_IP_ADDRESS 192,168,178,87

// If using static ip you need to define Gateway and Subnet address as well
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0


// MQTT broker ip address.
#define MY_CONTROLLER_IP_ADDRESS 10, 10, 0, 10

// The MQTT broker port to to open
#define MY_PORT 1883

/*
// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
*/

#include <ESP8266WiFi.h>
#include <MySensors.h>
#include <SPI.h>
#include <DHT.h>

// Set this to the pin you connected the DHT's data pin to
#define DHT_DATA_PIN 2

// Set this offset if the sensor has a permanent small offset to the real temperatures
#define SENSOR_TEMP_OFFSET 0

// Sleep time between sensor updates (in milliseconds)
// Must be >1000ms for DHT22 and >2000ms for DHT11
static const uint64_t UPDATE_INTERVAL = 60000;
//const unsigned long SLEEP_TIME = 60000; 

// Force sending an update of the temperature after n sensor reads, so a controller showing the
// timestamp of the last update doesn't show something like 3 hours in the unlikely case, that
// the value didn't change since;
// i.e. the sensor would force sending an update every UPDATE_INTERVAL*FORCE_UPDATE_N_READS [ms]
static const uint8_t FORCE_UPDATE_N_READS = 10;

#define CHILD_ID_HUM 0
#define CHILD_ID_TEMP 1

float lastTemp;
float lastHum;
uint8_t nNoUpdatesTemp;
uint8_t nNoUpdatesHum;
bool metric = true;

MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
DHT dht;



void presentation()
{ 
  // Send the sketch version information to the gateway
  sendSketchInfo("TemperatureAndHumidity", "1.1");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID_HUM, S_HUM);
  present(CHILD_ID_TEMP, S_TEMP);

  metric = getConfig().isMetric;
}


void setup()
{
  dht.setup(DHT_DATA_PIN); // set data pin of DHT sensor
  if (UPDATE_INTERVAL <= dht.getMinimumSamplingPeriod()) {
    Serial.println("Warning: UPDATE_INTERVAL is smaller than supported by the sensor!");
  }
  // Sleep for the time of the minimum sampling period to give the sensor time to power up
  // (otherwise, timeout errors might occure for the first reading)
  wait(dht.getMinimumSamplingPeriod());
}


void loop()      
{  
  // Force reading sensor, so it works also after sleep()
  dht.readSensor(true);

  // Get temperature from DHT library
  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
    Serial.println("Failed reading temperature from DHT!");
  } else if (temperature != lastTemp || nNoUpdatesTemp == FORCE_UPDATE_N_READS) {
    // Only send temperature if it changed since the last measurement or if we didn't send an update for n times
    lastTemp = temperature;
    if (!metric) {
      temperature = dht.toFahrenheit(temperature);
    }
    // Reset no updates counter
    nNoUpdatesTemp = 0;
    temperature += SENSOR_TEMP_OFFSET;
    send(msgTemp.set(temperature, 1));

    #ifdef MY_DEBUG
    Serial.print("T: ");
    Serial.println(temperature);
    #endif
  } else {
    // Increase no update counter if the temperature stayed the same
    nNoUpdatesTemp++;
  }

  // Get humidity from DHT library
  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
    Serial.println("Failed reading humidity from DHT");
  } else if (humidity != lastHum || nNoUpdatesHum == FORCE_UPDATE_N_READS) {
    // Only send humidity if it changed since the last measurement or if we didn't send an update for n times
    lastHum = humidity;
    // Reset no updates counter
    nNoUpdatesHum = 0;
    send(msgHum.set(humidity, 1));

    #ifdef MY_DEBUG
    Serial.print("H: ");
    Serial.println(humidity);
    #endif
  } else {
    // Increase no update counter if the humidity stayed the same
    nNoUpdatesHum++;
  }

  // Sleep for a while to save energy
  wait(UPDATE_INTERVAL); 
}

This is working great. So I have a working temp / humidity sensor.

Ploughing on I mashed my working mqtt dht example with the motion example and realisied i might have bitten off more than I can chew...

Stepping back I thought ok just try MQTT + Motion Here's the sketch.

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 *
 * DESCRIPTION
 * The ESP8266 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
 * The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
 *
 * LED purposes:
 * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
 * nRF24L01+  ESP8266
 * VCC        VCC
 * CE         GPIO4
 * CSN/CS     GPIO15
 * SCK        GPIO14
 * MISO       GPIO12
 * MOSI       GPIO13
 *
 * Not all ESP8266 modules have all pins available on their external interface.
 * This code has been tested on an ESP-12 module.
 * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
 * - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch')
 * - Connect GPIO15 via 10K pulldown resistor to GND
 * - Connect CH_PD via 10K resistor to VCC
 * - Connect GPIO2 via 10K resistor to VCC
 * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
 *
  * Inclusion mode button:
 * - Connect GPIO5 via switch to GND ('inclusion switch')
 *
 * Hardware SHA204 signing is currently not supported!
 *
 * Make sure to fill in your ssid and WiFi password below for ssid & pass.
 */


// Enable debug prints to serial monitor
#define MY_DEBUG

// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600

// Enables and select radio type (if attached)
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_GATEWAY_MQTT_CLIENT
#define MY_GATEWAY_ESP8266

// Set this node's subscribe and publish topic prefix
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway2-out"
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway2-in"

// Set MQTT client id
#define MY_MQTT_CLIENT_ID "mysensors-2"

// Enable these if your MQTT broker requires usenrame/password
//#define MY_MQTT_USER "username"
//#define MY_MQTT_PASSWORD "password"

// Set WIFI SSID and password
#define MY_ESP8266_SSID "XXXXXXXXXXXXXXXX"
#define MY_ESP8266_PASSWORD "XXXXXXXXXXXXXXXXX"

// Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static.
// #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway"

// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
//#define MY_IP_ADDRESS 192,168,178,87

// If using static ip you need to define Gateway and Subnet address as well
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0


// MQTT broker ip address.
#define MY_CONTROLLER_IP_ADDRESS 10, 10, 0, 10

// The MQTT broker port to to open
#define MY_PORT 1883

/*
// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
#define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
*/

#include <ESP8266WiFi.h>
#include <MySensors.h>


unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 2   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define CHILD_ID 1   // Id of the sensor child

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()
{
    pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()
{
    // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Motion Sensor", "1.0");

    // Register all sensors to gw (they will be created as child devices)
    present(CHILD_ID, S_MOTION);
}

void loop()
{
    // Read digital motion value
    bool tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;

    Serial.println(tripped);
    send(msg.set(tripped?"1":"0"));  // Send tripped value to gw

    // Sleep until interrupt comes in on motion sensor. Send update every two minute.
    sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
}

The node comes up and mqtt gateway registers with mybroker.

See the serial log here:

oÈHìè‰CGH,xI$ø0;255;3;0;9;MCO:BGN:INIT GW,CP=R-NGE--,VER=2.1.0
scandone
f 0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 8
cnt 

connected with LakeNET, channel 1
dhcp client start...
.ip:10.10.0.235,mask:255.255.255.0,gw:10.10.0.1
.IP: 10.10.0.235
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;9;MCO:BGN:INIT OK,TSP=NA
IP: 10.10.0.235
0;255;3;0;9;Attempting MQTT connection...
0;255;3;0;9;MQTT connected
0;255;3;0;9;Sending message on topic: mygateway2-out/0/255/0/0/17
0;255;3;0;9;Sending message on topic: mygateway2-out/0/255/3/0/11
0;255;3;0;9;Sending message on topic: mygateway2-out/0/255/3/0/12
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/0/0/1
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
1
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
0;255;3;0;9;MCO:SLP:WUP=-2
0
0;255;3;0;9;Sending message on topic: mygateway2-out/0/1/1/0/16
0;255;3;0;9;MCO:SLP:MS=120000,SMS=0,I1=2,M1=3,I2=255,M2=255
pm open,type:2 0

But the sketch that looks like it should sleep for 2 mins if there is no motion (i have the sensor face down) but the sketch just keeps runnning away.

I am not sure if its the code or something to do with the hardware / how I am wired. Just not sure about this whole interrupt thing.

Any pointers will be gratefully received.