3. Multi-Binary Switch Sketch

Multi-Binary Switch Sketch

  • mikeones

    Anyone have a working example of a multi-switch sketch? I have started to modify the BinarySwitchSensor.ino sketch but I am not sure how to get the debouce settings per switch or if it is needed. I have attached my sketch and error that results when I try an compile this. Any suggestions?

    BinarySwitchSensor.ino: In function ‘void setup()’:
BinarySwitchSensor:39: error: request for member ‘attach’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:40: error: request for member ‘interval’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor.ino: In function ‘void loop()’:
BinarySwitchSensor:54: error: request for member ‘update’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:56: error: request for member ‘read’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:61: error: lvalue required as left operand of assignment

    This is the code so far.

    // Simple binary switch example 
// Connect button or door/window reed switch between 
// digitial I/O pin 3 (ZONE_1 below) and GND.

#include <Sensor.h>
#include <SPI.h>
#include <EEPROM.h>  
#include <RF24.h>
#include <Bounce2.h>

#define ZONE_1  14  // Arduino Digital I/O pin for button/reed switch
#define NUMBER_OF_ZONES 6

Sensor gw;
Bounce debouncer_1 = Bounce();
Bounce debouncer_2 = Bounce();
Bounce debouncer_3 = Bounce();
Bounce debouncer_4 = Bounce();
Bounce debouncer_5 = Bounce();
Bounce debouncer_6 = Bounce();

int oldValue_1 =-1;
int oldValue_2 =-1;
int oldValue_3 =-1;
int oldValue_4 =-1;
int oldValue_5 =-1;
int oldValue_6 =-1;

void setup()  
{  
  gw.begin();
  for (int i=0; i<NUMBER_OF_ZONES;i++) {
   // Setup the button
	pinMode(ZONE_1+i,INPUT);
	// Activate internal pull-up
	digitalWrite(ZONE_1+i,HIGH);
	
	// After setting up the button, setup debouncer
	debouncer_1+i.attach(ZONE_1+i);
	debouncer_1+i.interval(5);
	
	// Register binary input sensor to gw (they will be created as child devices)
	// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
	// If S_LIGHT is used, remember to update variable type you send in below.
	gw.sendSensorPresentation(ZONE_1+i, S_DOOR);
  }
}


//  Check if digital input has changed and send in new value
void loop() 
{
  for (int i=0; i<NUMBER_OF_ZONES;i++) {
	debouncer_1+i.update();
	// Get the update value
	int value = debouncer_1+i.read();
   
	if (value != oldValue_1+i) {
	   // Send in the new value
	   gw.sendVariable(ZONE_1+i, V_TRIPPED, value==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
	   oldValue_1+i = value;
	}
  }
}
    0 BulldogLowell 1 Reply
  • BulldogLowell
    Contest Winner

    @mikeones said:

    Anyone have a working example of a multi-switch sketch? I have started to modify the BinarySwitchSensor.ino sketch but I am not sure how to get the debouce settings per switch or if it is needed. I have attached my sketch and error that results when I try an compile this. Any suggestions?

    BinarySwitchSensor.ino: In function ‘void setup()’:
BinarySwitchSensor:39: error: request for member ‘attach’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:40: error: request for member ‘interval’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor.ino: In function ‘void loop()’:
BinarySwitchSensor:54: error: request for member ‘update’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:56: error: request for member ‘read’ in ‘i’, which is of non-class type ‘int’
BinarySwitchSensor:61: error: lvalue required as left operand of assignment

    This is the code so far.

    // Simple binary switch example
    // Connect button or door/window reed switch between
    // digitial I/O pin 3 (ZONE_1 below) and GND.

    #include <Sensor.h>
    #include <SPI.h>
    #include <EEPROM.h>
    #include <RF24.h>
    #include <Bounce2.h>

    #define ZONE_1 14 // Arduino Digital I/O pin for button/reed switch
    #define NUMBER_OF_ZONES 6

    Sensor gw;
    Bounce debouncer_1 = Bounce();
    Bounce debouncer_2 = Bounce();
    Bounce debouncer_3 = Bounce();
    Bounce debouncer_4 = Bounce();
    Bounce debouncer_5 = Bounce();
    Bounce debouncer_6 = Bounce();

    int oldValue_1 =-1;
    int oldValue_2 =-1;
    int oldValue_3 =-1;
    int oldValue_4 =-1;
    int oldValue_5 =-1;
    int oldValue_6 =-1;

    void setup()
    {
    gw.begin();
    for (int i=0; i<NUMBER_OF_ZONES;i++) {
    // Setup the button
    pinMode(ZONE_1+i,INPUT);
    // Activate internal pull-up
    digitalWrite(ZONE_1+i,HIGH);

      // After setting up the button, setup debouncer
  debouncer_1+i.attach(ZONE_1+i);
  debouncer_1+i.interval(5);
  
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in below.
  gw.sendSensorPresentation(ZONE_1+i, S_DOOR);
}

    }

    // Check if digital input has changed and send in new value
    void loop()
    {
    for (int i=0; i<NUMBER_OF_ZONES;i++) {
    debouncer_1+i.update();
    // Get the update value
    int value = debouncer_1+i.read();

      if (value != oldValue_1+i) {
     // Send in the new value
     gw.sendVariable(ZONE_1+i, V_TRIPPED, value==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
     oldValue_1+i = value;
  }
}

    }

    debouncer_1+i.attach(ZONE_1+i);

    yeah, you are trying to add an integer to a string

    the Bounce2.h library complains about that syntax, I cannot find good examples with multi pushbuttons.

    bounce.h seems a little more friendly to your needs, and a better set of instructions.

    0
  • mikeones

    I did get this code to compile... I am going to test with this over the weekend.

    // Simple binary switch example 
// Connect button or door/window reed switch between 
// digitial I/O pin 3 (ZONE_1 below) and GND.

#include <Sensor.h>
#include <SPI.h>
#include <EEPROM.h>  
#include <RF24.h>
#include <Bounce2.h>

#define ZONE_1  14  // Arduino Digital I/O pin for button/reed switch
#define NUMBER_OF_ZONES 6

Sensor gw;
Bounce debouncer_1 = Bounce();
Bounce debouncer_2 = Bounce();
Bounce debouncer_3 = Bounce();
Bounce debouncer_4 = Bounce();
Bounce debouncer_5 = Bounce();
Bounce debouncer_6 = Bounce();

int oldValue_1 =-1;
int oldValue_2 =-1;
int oldValue_3 =-1;
int oldValue_4 =-1;
int oldValue_5 =-1;
int oldValue_6 =-1;

void setup()  
{  
  gw.begin();
  for (int i=0; i<NUMBER_OF_ZONES;i++) {
   // Setup the button
	pinMode(ZONE_1+i,INPUT);
	// Activate internal pull-up
	digitalWrite(ZONE_1+i,HIGH);
	
	// After setting up the button, setup debouncer
	switch (1+i) {
	  case 1:
		debouncer_1.attach(ZONE_1);
		debouncer_1.interval(5);
		break;
	  case 2:
		debouncer_2.attach(ZONE_1+i);
		debouncer_2.interval(5);
		break;
	  case 3:
		debouncer_3.attach(ZONE_1+i);
		debouncer_3.interval(5);
		break;
	  case 4:
		debouncer_4.attach(ZONE_1+i);
		debouncer_4.interval(5);
		break;
	  case 5:
		debouncer_5.attach(ZONE_1+i);
		debouncer_5.interval(5);
		break;
	}
	
	// Register binary input sensor to gw (they will be created as child devices)
	// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
	// If S_LIGHT is used, remember to update variable type you send in below.
	gw.sendSensorPresentation(ZONE_1+i, S_DOOR);
	delay(1000);
  }
}


//  Check if digital input has changed and send in new value
void loop() 
{
  for (int i=0; i<NUMBER_OF_ZONES;i++) {
	int num = 1+i;
	// Get the update value
	switch (num) {
	  case 1:
		{
		  debouncer_1.update();
		  int value_1 = debouncer_1.read();
		  if (value_1 != oldValue_1) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_1==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_1 = value_1;
		  }
		  break;
		}
	  case 2:
		{
		  debouncer_2.update();
		  int value_2 = debouncer_2.read();
		  if (value_2 != oldValue_2) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_2==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_2 = value_2;
		  }
		  break;
		}
	  case 3:
		{
		  debouncer_3.update();
		  int value_3 = debouncer_3.read();
		  if (value_3 != oldValue_3) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_3==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_3 = value_3;
		  }
		  break;
		}
	  case 4:
		{
		  debouncer_4.update();
		  int value_4 = debouncer_4.read();
		  if (value_4 != oldValue_4) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_4==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_4 = value_4;
		  }
		  break;
		}
	  case 5:
		{
		  debouncer_5.update();
		  int value_5 = debouncer_5.read();
		  if (value_5 != oldValue_5) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_5==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_5 = value_5;
		  }
		  break;
		}
	  case 6:
		{
		  debouncer_6.update();
		  int value_6 = debouncer_6.read();
		  if (value_6 != oldValue_6) {
		   // Send in the new value
		   gw.sendVariable(ZONE_1+i, V_TRIPPED, value_6==HIGH ? "1" : "0");  // Change to V_LIGHT if you use S_LIGHT in presentation above
		   oldValue_6 = value_6;
		  }
		break;
		}
	}
  }
}
    0
Log in to reply
 

Suggested Topics

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts



Copyright 2019 Sensnology   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service