Powering with LiPo a mini pro without regulator
-
The original nrf may support 3.6 but the chinese models that i have die faster :'/
-
The original nrf may support 3.6 but the chinese models that i have die faster :'/
@Vladut-Grecu
Good point. -
What I don`t get is why you want to cut the 3.3v regulator when you only get a 220 micro Amps consumption reduction and the resistors that you use to measure the actual voltage over the Analog pin use way more..
Use the internal arduino voltage measure. You will see 3.3v even if you get over 3.3v but what you actually need know is when the voltage drops under 3.3v so you know when you have to start recharging your li-po.
-
What I don`t get is why you want to cut the 3.3v regulator when you only get a 220 micro Amps consumption reduction and the resistors that you use to measure the actual voltage over the Analog pin use way more..
Use the internal arduino voltage measure. You will see 3.3v even if you get over 3.3v but what you actually need know is when the voltage drops under 3.3v so you know when you have to start recharging your li-po.
@Vladut-Grecu
"the resistors that you use to measure the actual voltage over the Analog pin use way more" ??The recommended voltage divider for 2AAs is 1M+470k and e.g. for 4AAs I use 1M+5M with success.. ~1uA is not that much.
-
The rezistors + the code that needs to be run? The extra cycles for you to read the Analog pin? I go with the idea that if there is allready a measuring in the arduino anyway why do i need to reinvent the wheel? The voltage divider thingy is ok if you want to measure voltages that go over the vcc value
-
The rezistors + the code that needs to be run? The extra cycles for you to read the Analog pin? I go with the idea that if there is allready a measuring in the arduino anyway why do i need to reinvent the wheel? The voltage divider thingy is ok if you want to measure voltages that go over the vcc value
@Vladut-Grecu
The internal method is the obvious choice when battery voltage is Vcc. Whether you need regulator, step-up/down etc or not, is determined by things like sensors and battery range etc.I doubt there are extra cycles compared to the internal method. Besides, I'd say the power loss from extra cycles would be neglectable
Regarding the use of voltage divider above and under Vcc, I refer to my answer here.
-
@m26872 said:
the power loss from extra cycles would be neglectable
You are right. But 220uA are neglectable aswell. (For me at least)
@Vladut-Grecu said:
But 220uA are neglectable aswell. (For me at least)
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
-
It lasted 2 minutes because you read the sensor way to often. For an extended battery life you need to put the arduino to sleep for as much as possible and read the sensors value very rarely.
@Vladut-Grecu not really, but keep in mind that some sensors need to reach the needed temperature to be read, so you may need to heat for 10 minutes before reading and thus you will drain your battery. Also, even with a slepp, you may need an on/off on powering the gas sensor for it is continuously powered.
-
Did you consider not recharging the battery over 3.3v? The nrf's 3.3v is a must. You can't go over 3.378v. (tested by me, before the poor little guy fried)
Sorry, I've been swamped the last couple of days.
@Vladut-Grecu said:
Did you consider not recharging the battery over 3.3v? The nrf's 3.3v is a must. You can't go over 3.378v. (tested by me, before the poor little guy fried)
LiPo batteries should not go below 3V if I'm not mistaken, so charging it to 3.3V would make me recharge it more often. The sensor is for my folks because they still have butane gas for hot water, so I'd like it to last as long as possible. If, like you say, the chinese clon can't operate at more than 3.378V, I'll stick to 2 x AA batteries.
As the main power drain occurs when the sensor reads and the radio sends, I thought of measuring the battery just after that happens, which in this case it'd be like a minute or so. Therefore the extra cycles to read the analog input should be negligible.
About the step up converter, the store has a couple listed. This one http://goo.gl/1gwmm2 has a usb input and the other one http://www.ebay.com/itm/291352631612?rmvSB=true doesn't. The second one is better to use ion this case, isn't it?
@epierre said in Powering with LiPo a mini pro without regulator:
@Vladut-Grecu not really, but keep in mind that some sensors need to reach the needed temperature to be read, so you may need to heat for 10 minutes before reading and thus you will drain your battery. Also, even with a slepp, you may need an on/off on powering the gas sensor for it is continuously powered.
So you say the sensor would be continuously powered even though we do a gw.sleep?? The heater has a power consumption of 900mW.
-
Neither. Those will boost it till 5v. You need something like this.
-
Neither. Those will boost it till 5v. You need something like this.
@Vladut-Grecu said:
Neither. Those will boost it till 5v. You need something like this.
But that one wouldn't be enough to feed the 5V that the MQ-2 gas sensor requires, would it?
-
@Vladut-Grecu said:
But 220uA are neglectable aswell. (For me at least)
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
@m26872 said:
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
My take on low power measurement.
I have not gotten around to actually build it yet but I hope to do some measurements in my "lab" this spring. -
Oh.. for the gas sensor they are ok. Last one (green) seems a little bit more polished. The presence of the usb port is not important, you can solder it off. The usb is the output. Check the picture again. It's your choice.
-
Oh.. for the gas sensor they are ok. Last one (green) seems a little bit more polished. The presence of the usb port is not important, you can solder it off. The usb is the output. Check the picture again. It's your choice.
@Vladut-Grecu said:
Oh.. for the gas sensor they are ok. Last one (green) seems a little bit more polished. The presence of the usb port is not important, you can solder it off. The usb is the output. Check the picture again. It's your choice.
Yes, you're right, it's the output. I didn't take a close look to the image. The green one seems more polished as you say. I'll try with those.
@Anticimex said:
@m26872 said:
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
My take on low power measurement.
I have not gotten around to actually build it yet but I hope to do some measurements in my "lab" this spring.That's a very interesting project. In the thread some of you say that if VBatt = Vcc (no regulator like I'd like to have) then using the divider to measure the charge is non-sense and it's way better to use the internal functionality, Am I wrong?
-
@Vladut-Grecu said:
Oh.. for the gas sensor they are ok. Last one (green) seems a little bit more polished. The presence of the usb port is not important, you can solder it off. The usb is the output. Check the picture again. It's your choice.
Yes, you're right, it's the output. I didn't take a close look to the image. The green one seems more polished as you say. I'll try with those.
@Anticimex said:
@m26872 said:
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
My take on low power measurement.
I have not gotten around to actually build it yet but I hope to do some measurements in my "lab" this spring.That's a very interesting project. In the thread some of you say that if VBatt = Vcc (no regulator like I'd like to have) then using the divider to measure the charge is non-sense and it's way better to use the internal functionality, Am I wrong?
@Viper_Scull
I have not looked into how internal measurement is done. So I don't know what constraints that type of measurement has. But for external measurement using a voltage divider allows the measurement point to be biased with respect to the ADC reference voltage and my proposal limits the standby current draw of the voltage divider.
But if no regulator is done internal measuring is provable better, how that now can be achieved. I am guessing by using vcc as reference to the ADC. -
Right. Thanks. That was something along the line with what I expected. I think it is an adequate option as long as you run the Arduino directly off the battery (without regulation). But with regulation it won't work.
-
@Vladut-Grecu said:
Oh.. for the gas sensor they are ok. Last one (green) seems a little bit more polished. The presence of the usb port is not important, you can solder it off. The usb is the output. Check the picture again. It's your choice.
Yes, you're right, it's the output. I didn't take a close look to the image. The green one seems more polished as you say. I'll try with those.
@Anticimex said:
@m26872 said:
Sorry, but the 220uA is drawn continously. Since most of my (and many others) battery applications have long sleep durations, the sleep mode power consumption is the first priority. Second is probably limiting the radio usage (meaning you can do things with just the arduino).
My take on low power measurement.
I have not gotten around to actually build it yet but I hope to do some measurements in my "lab" this spring.That's a very interesting project. In the thread some of you say that if VBatt = Vcc (no regulator like I'd like to have) then using the divider to measure the charge is non-sense and it's way better to use the internal functionality, Am I wrong?
@Viper_Scull said:
"...way better to use the internal functionality, Am I wrong?"
Yes, "way better" given that it is a real low-power application. Saving 1uA and 2 resistors isn't always that important.
-
@Viper_Scull said:
"...way better to use the internal functionality, Am I wrong?"
Yes, "way better" given that it is a real low-power application. Saving 1uA and 2 resistors isn't always that important.
