RGB Leds Light - Mood Light

OliverDog

I think most people have already seen that 15 dollars multisensor build by Ben from BruhAutomation.
Here is the link: https://www.youtube.com/watch?v=jpjfVc-9IrQ

Unfortunately (at least for this community) he uses a NomeMCU board instead of using a MySensors connection.

It would be awesome porting that whole sketch and project to a MySensors battery powered node... sorry if I am missing somebody´s work that already did that.

All the sensors together are relatively easy to build on mysensor, but what I can´t figure out is that awesome RGB LED wich turns into a complete Light Component, with fade, color changing and transitions.

Could someone share a mysensors node or help porting that Bruh Sketch, specially the RGB Led part?

It would be something like a Mood Light!

Here is original code:
https://github.com/bruhautomation/ESP-MQTT-JSON-Multisensor

BartE

@OliverDog here is a link to such a sketch (https://forum.mysensors.org/topic/2160/my-mysensors-rgbw-plug-in-has-an-init-problem)

OliverDog

Thanks @BartE !

Three more questions:

Will it work with a single 4 pin RGB LED common cathode instead of a LED strip?
Will it work with Home Assistant Controller like a ordinary RGB Light?
Could it run on batteries?

Thanks again.

BartE

Hi @OliverDog , yes this should work

Will it work with a single 4 pin RGB LED common cathode instead of a LED strip?
--> Uncomment this line "#define RGBW 1" to make it three color (RGB) in stead of four (RGBW).
Will it work with Home Assistant Controller like a ordinary RGB Light?
--> Should work with HAC since it presents it self as a RGB module
Could it run on batteries?
--> Yes why not, but please do read some forum posts about what to think about when running mysensors on batteries, there are several of them

OliverDog

Finally I tried this weekend but no success...

First I have updated your sketch to 2.0 version (I think I made everything right)
Didn't work on Home Assistant because the sketch don't send an initial value for each configuration of the Leds, such as Dimmer, RGB, Light, Fade, etc.

I did not figure out how to create an initial value loop because there are no MyMessage msg(Child_, V_) on the sketch...

Could you help me again?
Thanks very much...

Here is the updated sketch:

// RBG led strip plug in.
// by Bart Eversdijk (c) 2015.

#define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_NODE_ID 3

#include <MySensors.h>
#include <SPI.h>

#define SUBID  1  // sensor number needed in the custom devices set up

#define RED   6  // Arduino PWM pin for Red
#define GREEN 5 // Arduino PWM pin for Green
#define BLUE  3  // Arduino PWM pin for Blue
#define NODENAME "RGB Led2"

enum ANIMATIOMODES {RAINBOW=0,RANDONMIZE,FADERGB,FADEMULTICOLR,FLASHCOLOR,LAST_PROGRAM};

byte FADE_RGB_COLOR_MODES[]   = {0b0010,0b0011,0b0100,0b0101,0b1000,0b1001, 0xFF};
byte FADE_MULTI_COLOR_MODES[] = {0b0010,0b0011,0b0110,0b0111,0b0100,0b0101,0b1100,0b1101,0b1000,0b1001,0b1010,0b1011,0xFF};

static bool first_message_sent = false;

byte rgb_pins[]   = {RED, GREEN, BLUE};
byte ledOffValues[] = {0, 0, 0, 0};
byte rgb_values[]   = {0, 0, 0, 0};


void incomingMessage(const MyMessage &message);
#define NUM_OF_COLORS sizeof(rgb_pins)
int speedtable[] = { 0, 100, 50, 2 };
#define NUM_OF_SPEEDS sizeof(speedtable)

struct
{
   byte values[4];
   byte speedsetting;
   byte mode;
   bool status;
} rgb = { {0,0,0,0}, 0, RAINBOW, false};

bool    flashOn      = true;
int     syscounter   = 0;
int     lastUpdate   = 0;
bool    newSetting   = false;

void before() {
    // Set the rgb(w) pins in output mode
    for (int i = 0; i < NUM_OF_COLORS; i++) {
        pinMode(rgb_pins[i], OUTPUT);
    }
    recallEeprom();
    setLedValues(rgb.values, true);
    
    Serial.println("Init done");
}

void presentation()
{
  sendSketchInfo(NODENAME, "1.0");
  present(SUBID, S_RGB_LIGHT);
}

void loop()
{
    // Alway process incoming messages whenever possible
    if (speedtable[rgb.speedsetting] > 0) {
        if ((syscounter % speedtable[rgb.speedsetting]) == 0) {
           switch (rgb.mode)
           {
               case RAINBOW:
                 animateRainbowStep();
                 break;

               case FADERGB:
                 animateFadeColorStep(FADE_RGB_COLOR_MODES);
                 break;

               case FADEMULTICOLR:
                 animateFadeColorStep(FADE_MULTI_COLOR_MODES);
                 break;
             
              case FLASHCOLOR:
                 setLedValues(flashOn ? ledOffValues : rgb.values, false);
                 flashOn = !flashOn;
                 break;
                             
               case RANDONMIZE:
                 long number = random(0, 0xFFFFFF);
                 rgb_values[0] = number >> 16 & 0xFF ;
                 rgb_values[1] = number >> 8 & 0xFF ;
                 rgb_values[2] = number & 0xFF;
                 setLedValues(rgb_values, false);
                 break;
           }
        }
        delay(rgb.mode == RANDONMIZE || rgb.mode == FLASHCOLOR ? 50 : 1);
    }
    if (newSetting && (lastUpdate + 30000 < syscounter)) {   
        // Wait for a couple of seconds be fore actual storing the current setting in to EEPROM
        // This will save the EEPROM's life time, when playing around with colors
        Serial.println(" Store EERPOM");
        storeEeprom();
        newSetting = false;
    } 
    delay(1);
    syscounter++;
}

void animateRainbowStep()
{    
    static float counter = 0;
    float        pi      = 3.14159; 
    counter++;
    rgb_values[0] = map(sin(counter/100         )*1000,-1000,1000,0,255);
    rgb_values[1] = map(sin(counter/100 + pi*2/3)*1000,-1000,1000,0,255);
    rgb_values[2] = map(sin(counter/100 + pi*4/3)*1000,-1000,1000,0,255);
    setLedValues(rgb_values, false);
}

void animateFadeColorStep(byte *modes)
{    
    static int modecnt = 0;
    if (updateRGBValues(modes[modecnt] >> 1, (modes[modecnt] & 0x1) == 0x1)) { 
        modecnt = (modes[modecnt+1] == 0xFF ? 0 : modecnt + 1);
    }
}

bool updateRGBValues(byte mode, bool down)
{
    bool endReached = false;
    for (byte i = 0; i < 3; i++) {
        if (((mode >> i) & 0x1) == 0x1) {
           rgb_values[i] += (down ? -1 : 1);
           endReached    |= (down && (rgb_values[i] == 0x00)) || (!down && (rgb_values[i] == 0xFF));
        }
    }
    setLedValues(rgb_values, false);
    return endReached;
}


void incomingMessage(const MyMessage &message) {
    if (message.type == V_RGB || message.type == V_RGBW) {
  // starting to process the hex code
        String hexstring = message.getString();

        long number;
#ifdef RGBW
        char white[3];
        white[0] = hexstring[6];
        white[1] = hexstring[7];
        white[2] = 0;
        number = (long) strtol( &white[0], NULL, 16);
        rgb.values[3] = number & 0xFF;
#endif        
        hexstring[6] = 0;
        number = (long) strtol( &hexstring[0], NULL, 16);
        rgb.values[0] = number >> 16 & 0xFF ;
        rgb.values[1] = number >> 8 & 0xFF ;
        rgb.values[2] = number & 0xFF;
        
        rgb.speedsetting = 0;
        setLedValues(rgb.values, true);
        lastUpdate = syscounter;
        newSetting = true;
    }
    
    if (message.type == V_STATUS) {
      if (message.getBool()) {
          Serial.println("ON: Switch to last known color values");
          setLedValues(rgb_values, true);
      } else {
         Serial.println("OFF: Switch colors off");
         setLedValues(ledOffValues, true);
      }
      rgb.speedsetting = 0;
      rgb.status = message.getBool();
      lastUpdate = syscounter;
      newSetting = true;
    }
    
    if (message.type == V_VAR1) {
       Serial.println("Set speed and program value"); 
       byte newsetting = message.getByte();
       rgb.speedsetting = (newsetting >> 4) & 0x0F;
       byte newmode = newsetting & 0x0F;

       if (newmode != rgb.mode) {
           for (byte i = 0; i < NUM_OF_COLORS; i++) {
               rgb_values[i] = 0;
           }
           rgb.mode = newmode;
       }
       if (rgb.speedsetting > 0) {
         rgb.status = true;
       }
       lastUpdate = syscounter;
       newSetting = true;
      
       Serial.print("Data 0x");
       Serial.print(newsetting, HEX);
       Serial.print(" speed:");
       Serial.print(rgb.speedsetting);
       Serial.print(" mode:");
       Serial.println(rgb.mode);
    }
}

void setLedValues(byte *rgb, bool show)
{
    for (int i = 0; i < NUM_OF_COLORS; i++) {
        analogWrite(rgb_pins[i], rgb[i]);
    }  
 
    if (show) {
      Serial.print("Red: " );
      Serial.print(rgb[0], HEX);
      Serial.print("  Green: " );
      Serial.print(rgb[1], HEX);
      Serial.print("  Blue: " );
      Serial.print(rgb[2], HEX);
 #ifdef RGBW
        Serial.print("  White is " );
        Serial.print(rgb[3], HEX);
 #endif
      Serial.println();
    }
}

void storeEeprom()
{
    byte address = 0;
    byte *p = (byte *)&(rgb);
    for (byte i = 0; i < sizeof(rgb); i++) {
       saveState(address++, p[i]);
    }
}

void recallEeprom()
{
    byte address = 0;
    byte *p = (byte *)&(rgb);
    for (byte i = 0; i < sizeof(rgb); i++) {
       p[i] = loadState(address++);
    }
}

OliverDog

I tried another sketch from
https://forum.mysensors.org/topic/6765/rgb-led-strip

It worked with HASS but there is no response based on transitions time.

/**
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 * LED STRIP sketch for Mysensors
 *******************************
 *
 * REVISION HISTORY
 * 1.0 
 *   Based on the example sketch in mysensors
 * 1.1
 *   fadespeed parameter (send as V_VAR1 message)
 *   HomeAssistant compatible (send status to ack)
 */

#define MY_NODE_ID AUTO
#define MY_DEBUG
#define MY_RADIO_NRF24

#include <MySensors.h>

#define CHILD_ID_LIGHT 1

#define SN "LED Strip"
#define SV "1.1"

MyMessage lightMsg(CHILD_ID_LIGHT, V_LIGHT);
MyMessage rgbMsg(CHILD_ID_LIGHT, V_RGB);
MyMessage dimmerMsg(CHILD_ID_LIGHT, V_DIMMER);

byte red = 255;
byte green = 255;
byte blue = 255;
byte r0 = 255;
byte g0 = 255;
byte b0 = 255;
char rgbstring[] = "ffffff";

int on_off_status = 0;
int dimmerlevel = 100;
int fadespeed = 0;

#define REDPIN 6
#define GREENPIN 5
#define BLUEPIN 3

void setup()
{
  // Fix the PWM timer. Without this the LEDs will flicker.
  TCCR0A = _BV(COM0A1) | _BV(COM0B1) | _BV(WGM00);

  // Output pins
  pinMode(REDPIN, OUTPUT);
  pinMode(GREENPIN, OUTPUT);
  pinMode(BLUEPIN, OUTPUT);
  
}

void presentation()
{
	// Send the Sketch Version Information to the Gateway
	sendSketchInfo(SN, SV);
	present(CHILD_ID_LIGHT, S_RGB_LIGHT);
}

void loop()
{
  static bool first_message_sent = false;
  if ( first_message_sent == false ) {
    Serial.println( "Sending initial state..." );
    set_hw_status();
    send_status();
    first_message_sent = true;
  }
}

void receive(const MyMessage &message)
{
  int val;
  
	if (message.type == V_RGB) {
		Serial.println( "V_RGB command: " );
    Serial.println(message.data);
    long number = (long) strtol( message.data, NULL, 16);

    // Save old value
    strcpy(rgbstring, message.data);
    
    // Split it up into r, g, b values
    red = number >> 16;
    green = number >> 8 & 0xFF;
    blue = number & 0xFF;

    send_status();
    set_hw_status();

	} else if (message.type == V_LIGHT || message.type == V_STATUS) {
    Serial.println( "V_LIGHT command: " );
    Serial.println(message.data);
    val = atoi(message.data);
    if (val == 0 or val == 1) {
      on_off_status = val;
      send_status();
      set_hw_status();
    }
    
  } else if (message.type == V_DIMMER || message.type == V_PERCENTAGE) {
    Serial.print( "V_DIMMER command: " );
    Serial.println(message.data);
    val = atoi(message.data);
    if (val >= 0 and val <=100) {
      dimmerlevel = val;
      send_status();
      set_hw_status();
    }
    
  } else if (message.type == V_VAR1 ) {
    Serial.print( "V_VAR1 command: " );
    Serial.println(message.data);
    val = atoi(message.data);
    if (val >= 0 and val <= 2000) {
      fadespeed = val;
    }
    
	} else {
		Serial.println( "Invalid command received..." );
		return;
	}

}

void set_rgb(int r, int g, int b) {
  analogWrite(REDPIN, r);
  analogWrite(GREENPIN, g);
  analogWrite(BLUEPIN, b);
}

void set_hw_status() {
  int r = on_off_status * (int)(red * dimmerlevel/100.0);
  int g = on_off_status * (int)(green * dimmerlevel/100.0);
  int b = on_off_status * (int)(blue * dimmerlevel/100.0);

  if (fadespeed >0) {
    
    float dr = (r - r0) / float(fadespeed);
    float db = (b - b0) / float(fadespeed);
    float dg = (g - g0) / float(fadespeed);
    
    for (int x = 0;  x < fadespeed; x++) {
      set_rgb(r0 + dr*x, g0 + dg*x, b0 + db*x);
      delay(100);
    }
  }

  set_rgb(r, g, b);
 
  r0 = r;
  b0 = b;
  g0 = g;
  
}


void send_status() {
  send(rgbMsg.set(rgbstring));
  send(lightMsg.set(on_off_status));
  send(dimmerMsg.set(dimmerlevel));
}

RGB Leds Light - Mood Light

9

11.7k

11.2k

113.1k