Vera command to relay board
Vera
3
Posts
2
Posters
1.4k
Views
2
Watching
-
My MySensors gateway has been successfully communicating soil moisture sensor information to my Vera controller.
I now need to be able to send Vera commands to a relay board.
This is the sketch
// Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached #define MY_RADIO_NRF24 //#define MY_RADIO_RFM69 // Enable repeater functionality for this node #define MY_REPEATER_FEATURE #include <MySensors.h> #define RELAY_1 3 // Arduino Digital I/O pin number for first relay (second on pin+1 etc) #define NUMBER_OF_RELAYS 1 // Total number of attached relays #define RELAY_ON 1 // GPIO value to write to turn on attached relay #define RELAY_OFF 0 // GPIO value to write to turn off attached relay void before() { for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) { // Then set relay pins in output mode pinMode(pin, OUTPUT); // Set relay to last known state (using eeprom storage) digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF); } } void setup() { } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Relay", "1.0"); for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) { // Register all sensors to gw (they will be created as child devices) present(sensor, S_BINARY); } } void loop() { } void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type==V_STATUS) { // Change relay state digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF); // Store state in eeprom saveState(message.sensor, message.getBool()); // Write some debug info Serial.print("Incoming change for sensor:"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool());```Debug output
0 MCO:BGN:INIT REPEATER,CP=RNNRA---,VER=2.2.0-beta 4 MCO:BGN:BFR 6 TSM:INIT 6 TSF:WUR:MS=0 14 TSM:INIT:TSP OK 16 TSF:SID:OK,ID=1 18 TSM:FPAR 55 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 632 TSF:MSG:READ,0-0-1,s=255,c=3,t=8,pt=1,l=1,sg=0:0 636 TSF:MSG:FPAR OK,ID=0,D=1 2062 TSM:FPAR:OK 2062 TSM:ID 2064 TSM:ID:OK 2066 TSM:UPL 2070 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 2080 TSF:MSG:READ,0-0-1,s=255,c=3,t=25,pt=1,l=1,sg=0:1 2086 TSF:MSG:PONG RECV,HP=1 2091 TSM:UPL:OK 2091 TSM:READY:ID=1,PAR=0,DIS=1 2097 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 2105 TSF:MSG:READ,0-0-1,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 2113 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=18,pt=0,l=10,sg=0,ft=0,st=OK:2.2.0-beta 2123 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 2170 TSF:MSG:READ,0-0-1,s=255,c=3,t=6,pt=0,l=1,sg=0:M 2177 !TSF:MSG:PVER,0=2 2181 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=11,pt=0,l=5,sg=0,ft=0,st=OK:Relay 2189 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0 2199 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK: 2207 MCO:REG:REQ 2209 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2 2217 TSF:MSG:READ,0-0-1,s=255,c=3,t=27,pt=1,l=1,sg=0:1 2224 MCO:PIM:NODE REG=1 2226 MCO:BGN:STP 2228 MCO:BGN:INIT OK,TSP=1 29208 TSF:MSG:READ,0-0-1,s=1,c=1,t=2,pt=0,l=1,sg=1:0 29214 !TSF:MSG:PVER,0=2 63557 TSF:MSG:READ,0-0-1,s=1,c=1,t=2,pt=0,l=1,sg=1:1 63563 !TSF:MSG:PVER,0=2Vera log extract
grep Arduino LuaUPnP.log 02 07/11/17 13:51:05.869 luup_log:78: Arduino: Incoming internal command '1;255;3;0;21;0' discarded for child: 95 <0x2e52a680> 50 07/11/17 13:56:50.572 luup_log:78: Arduino: Sending: 1;1;1;1;2;1 <0x2adab000> 50 07/11/17 13:58:26.814 luup_log:78: Arduino: Sending: 1;1;1;1;2;1 <0x2adab000> 50 07/11/17 13:58:38.725 luup_log:78: Arduino: Presentation: 1;255;0;0;18;2.2.0-beta <0x2e52a680> 50 07/11/17 13:58:38.725 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,ArduinoLibVersion, 2.2.0-beta, 95 <0x2e52a680> 50 07/11/17 13:58:38.725 luup_log:78: Arduino: Warning: Sensor has different library version than GW. Id: 1;255 <0x2e52a680> 50 07/11/17 13:58:38.727 luup_log:78: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdate, 1499777918, 95 <0x2e52a680> 50 07/11/17 13:58:38.729 luup_log:78: Arduino: urn:micasaverde-com:serviceId:HaDevice1,LastUpdateHR, 13:58, 95 <0x2e52a680> 50 07/11/17 13:58:38.730 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNode, 0, 95 <0x2e52a680> 50 07/11/17 13:58:38.731 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,RelayNodeHR, GW, 95 <0x2e52a680> 50 07/11/17 13:58:38.731 luup_log:78: Arduino: Sending: 1;255;3;0;6;M <0x2e52a680> 50 07/11/17 13:58:38.814 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchName, Relay, 95 <0x2e52a680> 50 07/11/17 13:58:38.816 luup_log:78: Arduino: urn:upnp-arduino-cc:serviceId:arduinonode1,SketchVersion, 1.0, 95 <0x2e52a680> 50 07/11/17 13:58:38.817 luup_log:78: Arduino: Presentation: 1;1;0;0;3; <0x2e52a680> 50 07/11/17 13:59:05.812 luup_log:78: Arduino: Sending: 1;1;1;1;2;0 <0x2adab000> 50 07/11/17 13:59:40.214 luup_log:78: Arduino: Sending: 1;1;1;1;2;1 <0x2adab000>
As far as I can see clicking the 'On' or 'Off' buttons in the Vera plugin sends a message to the relay board, but I cannot understand why I'm getting the '!TSF:MSG:PVER,0=2' error (Message protocol version mismatch (actual!=expected) )?
-
@Woodside i think it is wise to bring all modules to same version.
- Your MySensors tile reports an old plugin version (1.5 latest version is 1.7) does not report a lib-version (gateway) but in your Vera log this message appears
50 07/11/17 13:58:38.725 luup_log:78: Arduino: Warning: Sensor has different library version than GW. Id: 1;255 <0x2e52a680>- And your repeater tile reports 2.2.0-beta
i would suggest to start using the stable released version 2.1.1 and try again.
