Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

help modify code

ago1980 last edited by ago1980

Hello, I would like to use this code with 2 relay 2 buttons, help me to change the code thank you very much
https://forum.mysensors.org/topic/6948/synchronising-light-switch
Reply Quote 0
1 Reply Last reply

1
Posts

646
Views

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

5

0
Votes

5
Posts

2060
Views

@karenbobiv I doubt it's related to the MySensors communication. Are you using a Dallas temp sensor? Could you check that the is actually connected to the dallas sensor by using isConnected(). When googling your problem I found a few hits on -196.6 which is the error code (DEVICE_DISCONNECTED) converted to Fahrenheit. Start debug mode (Config.h) to see what the sensor actually sends.
help please
Domoticz • • clivec

4

0
Votes

4
Posts

69
Views

@mutantx, sorry for the late reply, but I was on holidays I've no experience with this sketch code, nor the hardware build of this mp3 player. Try to contact the author of this player or you can check the general documentation about the use of V_VARx / S_CUSTOM : https://www.mysensors.org/download/serial_api_20 Try to break up things in little pieces when accumulating knowledge about mysensors. Big complicated sketches can be overwhelming. I start always, when troubleshouting, with the cleanest version of the script, with minimum code required for operation. And then I build it up.
Trying to automate in Domoticz
Domoticz • • Feliw05

4

0
Votes

4
Posts

33
Views

the problem is "if (switch.state == 'On') then" that not works, write: if (switch.active) then or if (switch.inActive) then Device attributes and methods for all devices
Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

8

0
Votes

8
Posts

896
Views

Someone know if it is problem with Domoticz or MySensors?
domoticz tables and mysensors
Domoticz • • ebioz

1

0
Votes

1
Posts

15
Views

No one has replied
How to get the bad status (red) for Temperature Node
Domoticz • • giangired

5

0
Votes

5
Posts

55
Views

Thanks everyone for the answers. However what I would like to do is create a routine with Dzvents that when I have the "red" indication (as shown in the image) causes a switch to operate which cuts the voltage to a device. The value of ".lastUpdate.minutesAgo" seems not to be the right solution because it continues to be increased in any case, regardless of the temperature value and the status of the "red" or normal indication.

help modify code

Suggested Topics

Vera Gateway Versions
Troubleshooting • • karenbobiv

help please
Domoticz • • clivec

Trying to automate in Domoticz
Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

domoticz tables and mysensors
Domoticz • • ebioz

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

66
Online

10.9k
Users

11.0k
Topics

112.3k
Posts

help modify code

Suggested Topics

Vera Gateway Versions Troubleshooting • • karenbobiv

help please Domoticz • • clivec

Trying to automate in Domoticz Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz Domoticz • • Tmaster

domoticz tables and mysensors Domoticz • • ebioz

How to get the bad status (red) for Temperature Node Domoticz • • giangired

66Online

10.9kUsers

11.0kTopics

112.3kPosts

Vera Gateway Versions
Troubleshooting • • karenbobiv

help please
Domoticz • • clivec

Trying to automate in Domoticz
Domoticz • • Feliw05

Roller shutter(s_cover) on Domoticz
Domoticz • • Tmaster

domoticz tables and mysensors
Domoticz • • ebioz

How to get the bad status (red) for Temperature Node
Domoticz • • giangired

66
Online

10.9k
Users

11.0k
Topics

112.3k
Posts