@user2684 the values stay at 0 forever in the display, everything else is working fine. Thanks

@user2684

Hi, I have a problem with values not showing in the DisplaySSD1306.

I have made a temperature and distance node with a Ds18b20 and a VL53L0X and also connected a DisplaySSD1306. Debug and sketch below. The thing is the values from the sensors are showing up correctly in the controller but the not in the display, only 0.00 is presenning in the display, any ideas of what is wrong?

Thanks!

Debug:

0 NM:INIT:VER=1.8
0 NM:INIT:INO=BMEDallas84 v1.1
0 NM:INIT:LIB VER=2.2.0 CP=RNNNA---
0 NM:INIT:RBT p=255
20 NM:BFR:INIT
2115 NM:BFR:OK
2135 NM:PRES:Temperatur(1) p=6 t=0
2173 NM:PRES:Avstånd(2) p=15 t=13
2212 NM:PRES:SSD1306(3) p=36 t=47
2259 NM:STP:ID=3 M=1
2443 NM:STP:HW V=4957 F=16 M=803
3210 NM:LOOP:Temperatur(1):SET t=0 v=20.00
4187 NM:LOOP:Temperatur(1):SET t=0 v=20.00
5164 NM:LOOP:Temperatur(1):SET t=0 v=20.02
6140 NM:LOOP:Temperatur(1):SET t=0 v=20.03
7116 NM:LOOP:Temperatur(1):SET t=0 v=20.03
7434 NM:LOOP:Avstånd(2):SET t=13 v=8190
7748 NM:LOOP:Avstånd(2):SET t=13 v=8190
8060 NM:LOOP:Avstånd(2):SET t=13 v=8190
8356 NM:LOOP:Avstånd(2):SET t=13 v=8190
8670 NM:LOOP:Avstånd(2):SET t=13 v=8190
8983 NM:SLP:SLEEP s=300

/**********************************
 * MySensors node configuration
 */

// General settings
#define SKETCH_NAME "BMEDallas84"
#define SKETCH_VERSION "1.1"


// NRF24 radio settings
#define MY_RADIO_NRF24
//#define MY_RF24_ENABLE_ENCRYPTION
#define MY_RF24_CHANNEL 84

#define MY_BAUD_RATE 9600
//#define MY_SMART_SLEEP_WAIT_DURATION_MS 500
#define MY_SPLASH_SCREEN_DISABLED

#define NODEMANAGER_DEBUG ON
#define NODEMANAGER_INTERRUPTS OFF
#define NODEMANAGER_SLEEP ON
#define NODEMANAGER_RECEIVE OFF
#define NODEMANAGER_DEBUG_VERBOSE OFF
#define NODEMANAGER_POWER_MANAGER OFF
#define NODEMANAGER_CONDITIONAL_REPORT OFF
#define NODEMANAGER_EEPROM OFF
#define NODEMANAGER_TIME OFF
#define NODEMANAGER_RTC OFF
#define NODEMANAGER_SD OFF
#define NODEMANAGER_HOOKING OFF
#define NODEMANAGER_OTA_CONFIGURATION OFF
#define NODEMANAGER_SERIAL_INPUT OFF

// import NodeManager library (a nodeManager object will be then made available)
#include <MySensors_NodeManager.h>

/***********************************
 * Add your sensors
 */
#include <sensors/SensorDs18b20.h>
SensorDs18b20 ds18b20(5);

#include <sensors/SensorVL53L0X.h>
SensorVL53L0X vl53l0x(4);

#include <sensors/DisplaySSD1306.h>
DisplaySSD1306 ssd1306;



// before
void before() {
	
  /***********************************
   * Configure your sensors
   */
   
  
  ds18b20.children.get(1)->setDescription("Temperatur");
  vl53l0x.children.get(1)->setDescription("Avstånd");
  ds18b20.setSamples(5);
  ds18b20.setSamplesInterval(200);
  vl53l0x.setSamples(5);
  vl53l0x.setSamplesInterval(200);
    nodeManager.setSleepMinutes(5);
  
  // call NodeManager before routine
  nodeManager.before();
}

// presentation
void presentation() {
  // call NodeManager presentation routine
  nodeManager.presentation();
}

// setup
void setup() {
  // call NodeManager setup routine
  nodeManager.setup();
}

// loop
void loop() {
  // call NodeManager loop routine
  nodeManager.loop();
}

#if NODEMANAGER_RECEIVE == ON
// receive
void receive(const MyMessage &message) {
  // call NodeManager receive routine
  nodeManager.receive(message);
}
#endif

#if NODEMANAGER_TIME == ON
// receiveTime
void receiveTime(unsigned long ts) {
  // call NodeManager receiveTime routine
  nodeManager.receiveTime(ts);
}
#endif

Thanks for your reply.
I do not know anything about programming or coding so I think it’s to complicated for me. (That’s why I like NM so much.)
But anyhow, thanks for your explanation and suggestion.

@user2684,
Hi,
I have a question, Is it possible to present an external sensor value on display with ModeManager?

I have an indoor temperature node with local presentation on a SSD1306 display. I like to present a battery powered temperature node located in my garden on the same display, is this possible using NodeManager?

If it´s possible can you give me an example how to do it?

Thanks!

@user2684 Thanks for your explanation, works great now!

@user2684
As you know I´m a fan of NodeManager!
Hi, I've downloaded the latest version of NodeManager, V1.7. Works really well based on what I've experienced so far. I especially appreciate the option of presenting results from nodes locally via LCD displays. I have tried making a simple node with a temperature DS18B20 and a display SSD1306, and it works well, but I would like to change the presentation of the child to another format/name that I choose myself, Is this possible? For me, it looks like the child is presented as a MAC address.!

@user2684 Thanks, Very much appreciated!

Hi @user2684
Is it possible to add sensor MG996R Servo in V1.7? I know the list is long for fixes but it would be nice if you could squeeze it in.

Thanks!

Thanks @user2684 for your reply,
I was using the wrong package, downloaded the latest version and now it works!

Thanks again for your help and for the development of NodeManager!

Error compiling DHT22 sensor

I'm trying to make a simple DHT22 sensor Nodemanagersketch

nodeManager.registerSensor(SENSOR_DHT22,6);

But when I try to compile I get a warning in the NodeManager.cpp file:
_dht->setup(_pin,_dht_type);

and in the bottom field 'class DHT' has no member named 'setup'

Does anyone know what I'm doing wrong?