I'm trying to set up a basic MySensors network. I have a NodeMCU hooked up to a NRF24L01+ with attena. It looks like it boots up normally. I also have an Arduino Nano hooked up to another NRF24 of the same type, but it has !TSM:FPAR:NO REPLY messages in the Serial console.
79 MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2 136 TSF:LRT:OK 152 TSM:INIT 165 TSF:WUR:MS=0 189 TSM:INIT:TSP OK scandone state: 0 -> 2 (b0) state: 2 -> 3 (0) state: 3 -> 5 (10) add 0 aid 10 cnt connected with REDACTED, channel 10 dhcp client start... ip:192.168.178.84,mask:255.255.255.0,gw:192.168.178.1 426 TSM:INIT:GW MODE 449 TSM:READY:ID=0,PAR=0,DIS=0 481 MCO:REG:NOT NEEDED 1580 GWT:TIN:CONNECTING... 2608 GWT:TIN:CONNECTING... scandone 3636 GWT:TIN:CONNECTING... 3665 GWT:TIN:IP: 192.168.178.84 3699 MCO:BGN:STP 3717 MCO:BGN:INIT OK,TSP=1 3745 TSM:READY:NWD REQ 3772 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK: pm open,type:2 0
It does not output any more messages after that.
__ __ ____ | \/ |_ _/ ___| ___ _ __ ___ ___ _ __ ___ | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __| | | | | |_| |___| | __/ | | \__ \ _ | | \__ \ |_| |_|\__, |____/ \___|_| |_|___/\___/|_| |___/ |___/ 2.3.2 16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=16,REL=255,VER=2.3.2 26 TSM:INIT 28 TSF:WUR:MS=0 34 TSM:INIT:TSP OK 36 TSM:INIT:STATID=10 38 TSF:SID:OK,ID=10 39 TSM:FPAR 1855 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 3863 !TSM:FPAR:NO REPLY 3865 TSM:FPAR 5681 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 7688 !TSM:FPAR:NO REPLY 7690 TSM:FPAR 9505 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 11512 !TSM:FPAR:NO REPLY 11514 TSM:FPAR 13330 ?TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 15338 !TSM:FPAR:FAIL 15339 TSM:FAIL:CNT=1 15341 TSM:FAIL:DIS 15343 TSF:TDI:TSL
This continues for a bit but it's just the same messages again.
A few notes:
- Both radios have 100uF capacitors
- I'm 99% they aren't fakes, they don't have the blob thingies
- I have not set up a controller yet, but the node has a static ID defined
- The gateway's NRF24 is at about 3.1v, the node's is at exactly 3.3v
- I have tried setting both of them to RF24_PA_MIN, this did not make a difference
- I have tried switching out the NodeMCU, but this did not make a difference
Any suggestions? Is this a hardware issue? I salvaged both NRF's from a previous project, and I couldn't get them to work then either. They might just not work.