Posts made by ruben_gr

ruben_gr

@mfalkvidd Yes. Thank you!

ruben_gr

Right, but if i use the same protocol i think that it's possible to connect both. I want to connect BeagleBone to PIC microcontroller, that is not supported by MySensors, but i will try to migrate from arduino to PIC. Thank you.

ruben_gr

It works, thank you for your patience!!

But just to understand it, why i don't need —my-controller-ip-address?

Btw, i want to build my own serial modules to connect to this gateway. Can you share with me the RS485 protocol of MySensors? Can i use RS485 just as a serial port without addresses?

Thank you again.

ruben_gr

@mfalkvidd thank you.

I want to connect MySensors gateway to my homeassistant. I check the ipaddress and are correct. Why do i get this error? Or how can i debug it?

Jun 20 10:21:22 DEBUG GWT:TPS:ETH OK
Jun 20 10:21:22 ERROR connect: Connection refused
Jun 20 10:21:22 ERROR failed to connect
Jun 20 10:21:22 DEBUG GWT:TPS:ETH OK
Jun 20 10:21:22 ERROR connect: Connection refused
Jun 20 10:21:22 ERROR failed to connect

ruben_gr

@mfalkvidd Why you think that this error is related to SPI? i'm not using RF modules neither GPIO, just ethernet.

ruben_gr

My sensors Transport Layer doesn't support serial too?

ruben_gr

I'm getting this error now, and i don't have nothing in parameters with GPIO9:

debian@beaglebone:~/MySensors$ sudo ./bin/mysgw
Jun 17 08:17:50 INFO  Starting gateway...
Jun 17 08:17:50 INFO  Protocol version - 2.3.2
Jun 17 08:17:50 DEBUG MCO:BGN:INIT GW,CP=RNNGL---,FQ=NA,REL=255,VER=2.3.2
Jun 17 08:17:50 DEBUG TSF:LRT:OK
Jun 17 08:17:50 DEBUG TSM:INIT
Jun 17 08:17:50 DEBUG TSF:WUR:MS=0
Jun 17 08:17:50 DEBUG !TSM:INIT:TSP FAIL
Jun 17 08:17:50 DEBUG TSM:FAIL:CNT=1
Jun 17 08:17:50 DEBUG TSM:FAIL:DIS
Jun 17 08:17:50 DEBUG TSF:TDI:TSL


Jun 17 08:18:00 DEBUG TSM:FAIL:RE-INIT
Jun 17 08:18:00 DEBUG TSM:INIT
Jun 17 08:18:11 ERROR Could not open /sys/class/gpio/gpio9/direction

ruben_gr

@mfalkvidd You are right! Sorry for my mistake, and thank you.

Ruben Rodrigues

ruben_gr

Hi,

I'm trying to install mysensors in beaglebone black as a gateway to connect to home assistant through ethernet, but it gives me this error:

debian@beaglebone:~/MySensors$ make
gcc -MT build/hal/architecture/Linux/drivers/core/log.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWDLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra  -I. -I./core -I./hal/architecte -c hal/architecture/Linux/drivers/core/log.c -o build/hal/architecture/Linux/drivers/core/log.o
gcc -MT build/hal/architecture/Linux/drivers/core/config.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GAG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra  -I. -I./core -I./hal/architcore -c hal/architecture/Linux/drivers/core/config.c -o build/hal/architecture/Linux/drivers/core/config.o
g++ -MT build/hal/architecture/Linux/drivers/core/StdInOutStream.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./cure/Linux/drivers/core -c hal/architecture/Linux/drivers/core/StdInOutStream.cpp -o build/hal/architecture/Linux/drivers/core/StdInOutStream.o
g++ -MT build/hal/architecture/Linux/drivers/core/noniso.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GAG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./x/drivers/core -c hal/architecture/Linux/drivers/core/noniso.cpp -o build/hal/architecture/Linux/drivers/core/noniso.o
g++ -MT build/hal/architecture/Linux/drivers/core/GPIO.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATE-DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hadrivers/core -c hal/architecture/Linux/drivers/core/GPIO.cpp -o build/hal/architecture/Linux/drivers/core/GPIO.o
hal/architecture/Linux/drivers/core/GPIO.cpp: In constructor ‘GPIOClass::GPIOClass()’:
hal/architecture/Linux/drivers/core/GPIO.cpp:53:33: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size 48 [-
    snprintf(file, sizeof(file), "/sys/class/gpio/%s/base", de->d_name);
                                 ^~~~~~~~~~~~~~~~~~~~~~~~~
hal/architecture/Linux/drivers/core/GPIO.cpp:53:12: note: ‘snprintf’ output between 22 and 277 bytes into a destination of size 64
    snprintf(file, sizeof(file), "/sys/class/gpio/%s/base", de->d_name);
    ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hal/architecture/Linux/drivers/core/GPIO.cpp:62:33: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size 48 [-
    snprintf(file, sizeof(file), "/sys/class/gpio/%s/ngpio", de->d_name);
                                 ^~~~~~~~~~~~~~~~~~~~~~~~~~
hal/architecture/Linux/drivers/core/GPIO.cpp:62:12: note: ‘snprintf’ output between 23 and 278 bytes into a destination of size 64
    snprintf(file, sizeof(file), "/sys/class/gpio/%s/ngpio", de->d_name);
    ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
g++ -MT build/hal/architecture/Linux/drivers/core/SPIDEV.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GAG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./x/drivers/core -c hal/architecture/Linux/drivers/core/SPIDEV.cpp -o build/hal/architecture/Linux/drivers/core/SPIDEV.o
g++ -MT build/hal/architecture/Linux/drivers/core/Print.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GAT -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./h/drivers/core -c hal/architecture/Linux/drivers/core/Print.cpp -o build/hal/architecture/Linux/drivers/core/Print.o
g++ -MT build/hal/architecture/Linux/drivers/core/EthernetClient.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./cure/Linux/drivers/core -c hal/architecture/Linux/drivers/core/EthernetClient.cpp -o build/hal/architecture/Linux/drivers/core/EthernetClient.o
g++ -MT build/hal/architecture/Linux/drivers/core/SerialPort.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/SerialPort.cpp -o build/hal/architecture/Linux/drivers/core/SerialPort.o
g++ -MT build/hal/architecture/Linux/drivers/core/Stream.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/Stream.cpp -o build/hal/architecture/Linux/drivers/core/Stream.o
g++ -MT build/hal/architecture/Linux/drivers/core/IPAddress.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/IPAddress.cpp -o build/hal/architecture/Linux/drivers/core/IPAddress.o
g++ -MT build/hal/architecture/Linux/drivers/core/compatibility.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/compatibility.cpp -o build/hal/architecture/Linux/drivers/core/compatibility.o
g++ -MT build/hal/architecture/Linux/drivers/core/interrupt.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/interrupt.cpp -o build/hal/architecture/Linux/drivers/core/interrupt.o
g++ -MT build/hal/architecture/Linux/drivers/core/SoftEeprom.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/SoftEeprom.cpp -o build/hal/architecture/Linux/drivers/core/SoftEeprom.o
g++ -MT build/hal/architecture/Linux/drivers/core/EthernetServer.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c hal/architecture/Linux/drivers/core/EthernetServer.cpp -o build/hal/architecture/Linux/drivers/core/EthernetServer.o
g++ -MT build/examples_linux/mysgw.o -MMD -MP -march=armv7-a -mtune=cortex-a8 -mfpu=neon -mfloat-abi=hard -DMY_RADIO_RF24 -DMY_GATEWAY_LINUX -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_LINUX_SERIAL_PORT=\"COM2\" -DMY_CONTROLLER_IP_ADDRESS=192,168,1,75:8123  -Ofast -g -Wall -Wextra -std=c++11 -I. -I./core -I./hal/architecture/Linux/drivers/core -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o
In file included from ./MySensors.h:244,
                 from examples_linux/mysgw.cpp:82:
./core/MyGatewayTransportEthernet.cpp: In function ‘bool gatewayTransportInit()’:
./core/MyGatewayTransportEthernet.cpp:57:40: error: expected primary-expression before ‘(’ token
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:223:21: note: in expansion of macro ‘_ethernetControllerIP’
  if (client.connect(_ethernetControllerIP, MY_PORT)) {
                     ^~~~~~~~~~~~~~~~~~~~~
<command-line>: error: expected ‘)’ before ‘:’ token
./core/MyGatewayTransportEthernet.cpp:57:41: note: in expansion of macro ‘MY_CONTROLLER_IP_ADDRESS’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                         ^~~~~~~~~~~~~~~~~~~~~~~~
./core/MyGatewayTransportEthernet.cpp:223:21: note: in expansion of macro ‘_ethernetControllerIP’
  if (client.connect(_ethernetControllerIP, MY_PORT)) {
                     ^~~~~~~~~~~~~~~~~~~~~
In file included from ./MySensors.h:244,
                 from examples_linux/mysgw.cpp:82:
./core/MyGatewayTransportEthernet.cpp:57:40: note: to match this ‘(’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:223:21: note: in expansion of macro ‘_ethernetControllerIP’
  if (client.connect(_ethernetControllerIP, MY_PORT)) {
                     ^~~~~~~~~~~~~~~~~~~~~
./core/MyGatewayTransportEthernet.cpp: In function ‘bool gatewayTransportSend(MyMessage&)’:
./core/MyGatewayTransportEthernet.cpp:57:40: error: expected primary-expression before ‘(’ token
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:272:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
<command-line>: error: expected ‘)’ before ‘:’ token
./core/MyGatewayTransportEthernet.cpp:57:41: note: in expansion of macro ‘MY_CONTROLLER_IP_ADDRESS’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                         ^~~~~~~~~~~~~~~~~~~~~~~~
./core/MyGatewayTransportEthernet.cpp:272:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
In file included from ./MySensors.h:244,
                 from examples_linux/mysgw.cpp:82:
./core/MyGatewayTransportEthernet.cpp:57:40: note: to match this ‘(’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:272:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
./core/MyGatewayTransportEthernet.cpp: In function ‘bool gatewayTransportAvailable()’:
./core/MyGatewayTransportEthernet.cpp:57:40: error: expected primary-expression before ‘(’ token
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:398:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
<command-line>: error: expected ‘)’ before ‘:’ token
./core/MyGatewayTransportEthernet.cpp:57:41: note: in expansion of macro ‘MY_CONTROLLER_IP_ADDRESS’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                         ^~~~~~~~~~~~~~~~~~~~~~~~
./core/MyGatewayTransportEthernet.cpp:398:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
In file included from ./MySensors.h:244,
                 from examples_linux/mysgw.cpp:82:
./core/MyGatewayTransportEthernet.cpp:57:40: note: to match this ‘(’
 #define _ethernetControllerIP IPAddress(MY_CONTROLLER_IP_ADDRESS)
                                        ^
./core/MyGatewayTransportEthernet.cpp:398:22: note: in expansion of macro ‘_ethernetControllerIP’
   if (client.connect(_ethernetControllerIP, MY_PORT)) {
                      ^~~~~~~~~~~~~~~~~~~~~
make: *** [Makefile:99: build/examples_linux/mysgw.o] Error 1

Configure command was:

./configure --my-debug=enable --my-gateway=ethernet --my-controller-ip-address=192.168.1.75:8123  --my-serial-port=COM2