Best posts made by Tiwo85

Hello,
Sorry for my bad english, I'm from Germany and my school english is about 20 years ago.
I'm trying to get this board working with Interrupts. https://www.openhardware.io/view/510/Multi-Sensor-TempHumidityPIR-LeakMagnetLightAccel

I try the sketch from NeverDie https://www.openhardware.io/view/499/10-years-wireless-PIR-Sensor-on-just-one-set-of-3-AAs#tabs-source and modify the pin configuration, but it doen't work. Then I take an example from ReadBearLabs and transfer MySensor routines into it. But this also doesn't work. Only when I use "My_Core_only" then the Interrupts are working pretty well, but when I disable "My_Core_only" the Interrupt doesn't work.

// SUMMARY: This demo sketch runs on the AM612 PIR v607 PCBto transmit battery voltage (heartbeat) and motion detections to a MySensors gateway using MySensors protocols.

// Note: because this is a passive node, node ID must be set manually to a unique sensor node ID:
#define MY_NODE_ID 143  // Passive mode requires static node ID

//#define MY_CORE_ONLY

#define MY_PASSIVE_NODE

#define MY_RADIO_NRF5_ESB



/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2017 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - tekka
 *
 * DESCRIPTION
 * Passive node example: This is a passive & independent reporting node
 *
 */

// This demo sketch also draws from the MySensor's example MotionSensor sketch.

#define IS_NRF51  //true iff the target is an nRF51.  If an nRF52, then comment this line out!

#define SHORT_WAIT 50

// Enable debug prints
//#define MY_DEBUG

#define PIN_LED1                (4) // 4 is sensor LED , 1 is onboard LED
#define LED_BUILTIN          PIN_LED1

#define PIN_SENSOR1                (10) // 2 is waterleak, 10 is PIR , 3 is Pin5/INT
#define SENSOR1         PIN_SENSOR1


#include <MySensors.h>

//#define CHILD_ID_TEMP 1  //definitions contributed by smilvert (see above credit)
#define CHILD_ID 2   // Id of the motion sensor child
#define ID_S_MULTIMETER        28

// Initialize general message
//MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
MyMessage msg(CHILD_ID, V_TRIPPED);
MyMessage msg_S_MULTIMETER_V_VOLTAGE(ID_S_MULTIMETER,V_VOLTAGE);

float batteryVoltage=0;  

/*#include "nrf_temp.h"

float read_temp_value(){

  float temp=0;

  // Starten Sie die Temperaturmessung. 
  NRF_TEMP->TASKS_START = 1; 

  // Warten Sie, bis die Temperaturmessung abgeschlossen ist.
  while (NRF_TEMP->EVENTS_DATARDY == 0){
    // Do nothing.}
  }
  NRF_TEMP->EVENTS_DATARDY = 0;

  // Lesen Sie den Temperaturwert vom Sensor ab
  // Die Genauigkeit beträgt 0,25 Grad Celsius <=> 1 Einheit = 0,25 Grad Celsius
  // Teile durch 4, um einen C-Wert zu erhalten
  
  temp = ((float)nrf_temp_read() / 4.);

  // Hoàn thành quá trình đo. 
  NRF_TEMP->TASKS_STOP = 1; 

  return temp;
}*/

void blinkityBlink(uint8_t repetitions) {
  for (int x=0;x<repetitions;x++) {
    digitalWrite(LED_BUILTIN ,HIGH);
    delay(20);
    digitalWrite(LED_BUILTIN ,LOW);
    delay(100);
    digitalWrite(LED_BUILTIN ,HIGH);
    delay(20);
    digitalWrite(LED_BUILTIN ,LOW);    
    if (x<(repetitions-1)) {  //skip waiting at the end of the final repetition
      delay(500);
    }
  }
}

void handle_irq3(void) {
  if(HIGH == digitalRead(SENSOR1)){
      digitalWrite(LED_BUILTIN , HIGH);
      send(msg.set("1"));  // motion detected
  }
  else
  {
      digitalWrite(LED_BUILTIN , LOW);
       send(msg.set("0"));  // send all-clear to prepare for future detections
  }
}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("NRF Motion Sensor", "1.0");
   // wait(SHORT_WAIT);
   // present(CHILD_ID_TEMP, S_TEMP,"Onboard Temperature");
  wait(SHORT_WAIT);
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_MOTION,"Motion Sensor");

  wait(SHORT_WAIT);
  
  present(ID_S_MULTIMETER,S_MULTIMETER,"Electric Station");
  wait(SHORT_WAIT);
}


void setup() {
    // put your setup code here, to run once:
    //hwInit();
  //hwPinMode(LED_BUILTIN,OUTPUT_D0H1);
  //hwPinMode(SENSOR1,INPUT);

   //nrf_temp_init();
  pinMode(LED_BUILTIN , OUTPUT);
    digitalWrite(LED_BUILTIN , LOW);
  blinkityBlink(5);  //signify power-up and start of operations

  // set interrupts, pin default is HIGH
  attachInterrupt(SENSOR1, handle_irq3, CHANGE);
}

void loop() {
  // put your main code here, to run repeatedly:
  //send(msgTemp.set(read_temp_value(),2));
  batteryVoltage=((float)hwCPUVoltage())/1000.0;  //take voltage measurement after transmission to hopefully measure lowest voltage that occurs. 
  send(msg_S_MULTIMETER_V_VOLTAGE.set(batteryVoltage,3));  //send battery voltage with 3 decimal places
  sleep(900000); //sleep 15 min
}```