Automated garage door

[dbemowsk]

@Dringie The only thing I think that I am going to add for now is to turn this on as a repeater node. I have this wired for power with an old modified wall brick cell phone charger that was 5 volts, so it will be powered all the time. I think it is a good place for a repeater anyway. If you find any problems or can suggest any improvements, I am all ears.

[Dringie]

I will also use signing when I get round to building this node.

Waiting for the signing chips from China.

I might add a relay for lights, so the lights come on at night when opened. (Night lua code to be used in domoticz).

Postman feature is something I'm going over in my head. E.g.. When postman delivers a parcel I can remotely open the garage slightly and it close again after 30 secs. Not sure if I want to write code in the node or in Domoticz. I think the node would be more fail proof.

[dbemowsk]

@Dringie What type of garage door opener do you have?

[Dringie]

@dbemowsk

Hormann motor, 3 section up and over door. I have placed position magnet sensors on the door runner.

My door works like yours with obstacles.

I will wire my node straight into the motor.

For the postman feature, I was going to add an extra reed switch on the runner to stop the door at a low hight.

[dbemowsk]

I had some problems using magnetic reed switches with my old HA setup. My main problem was that when the door would open, it would not always stop in the same spot. It was close to that spot, but enough off where the magnet wouldn't register. That was why I dug into the opener to find the limit switches. Going that route has been a ton more reliable since I am getting the state right from where the door opener tells the door to stop.See my very first pic in this post.

[cliffordbaker]

The idea of using relay is good as relay control one electrical circuit by opening and closing contacts in another circuit. In the programing model try to give a trigger input. This would work.

[dbemowsk]

For those interested, I have updated my sketch for my garage door controller to MySensors 2.0.

 /*
  MyGarageDoor for MySensors

  Arduino garage door control

  Originally built for MySensors 1.5 June 16,2016
  Updated to MySensors 2.0 October 21, 2016

  This will allow the MySensors gateway to monitor and control your garage door opener.  This will
  monitor the internal upper and lower limit switches of the door opener to determine door position
  for status as well as have a relay switched output that can control either the momentary contact
  switch connected to the door opener or wired directly to the switch contacts of a door opener
  remote to activate the door.

  This sketch features the following:

  Allows you to monitor the door position and return it's status based on the following:
    1 - When either the upper or lower door limit switches are reached, the door is said to be
        either fully open or fully closed. When a limit switch is triggered, the lastLimit and
        currentState variables are set to either OPEN or CLOSED based on the limit switch that was
        triggered.
    2 - If the upper and lower limit inputs both read high, then the door is said to be in motion.
        The door's direction of motion is determined from the lastLimit variable.  If the lastLimit
        of the door is OPEN, then the currentState variable should be set to CLOSING.  If the
        lastLimit of the door is CLOSED, then the currentState variable should be set to OPENING.
  Checks for door obstructions and throws an error by checking the currentState and lastLimit
  variables when the upper limit is reached.  If the upper limit is triggered and the currentState
  is set to CLOSING and the lastLimit is set to OPEN, this should indicate that the door reversed
  when closing and returned to the fully opened position.  The error state should only appear if
  BOTH the lastLimit and currentState conditions match.  If lastLimit is OPEN and the lastState is
  OPENING, this would indicate that the door was manually reversed.  This chech should only be
  needed when the upper limit is reached.
  Allows you to toggle the opener to either open or close the door.  When the door is toggled, the
  currentState should be checked and if the state is either OPENING or CLOSING, the currentState
  should invert telling that the door has changed direction.  This is done to prevent an error if
  the door is reversed manually when closing.

  PARTS LIST:
  Arduino pro mini
  nRF24L01 radio module
  AMS1117 3.3v regulator
  0.1uf capacitor
  10uf electrolytic capacitor
  4.7uf electrolytic capacitor (for radio module)
  5v reed relay
  2N3904 transistor for relay
  1k resistor
  Two small signal diodes for incoming signals from door opener

  Wiring from garage door opener
  Yellow = Upper limit D7
  Brown = Lower limit D8
  Gray = Signal ground

  Relay D5

  Version history:
  1.1 : Added the V_TEXT variable and S_INFO sensor type, and created the "Status" child
  1.2 : Added the heartbeat signal to tell the controller that the sensor is still alive.
        Scripting or other code must be used on the HA controller side to react to the 
        heartbeat signal and take appropriate action.
  2.0 : Converted to MySensors 2.0
*/

//Set up the nRF24L01+
#define MY_RADIO_NRF24

#include <SPI.h>
#include <MySensors.h>
#include <SimpleTimer.h>

#define SKETCH_NAME "MyGarageDoor"
#define SKETCH_VERSION "1.2"

#define CHILD_ID_OPENER 0
#define CHILD_ID_STATUS 1

#define UPPER_LIMIT_SENSOR 6  //Pin used for input from the garage door upper limit sensor
#define LOWER_LIMIT_SENSOR 7  //Pin used for input from the garage door lower limit sensor
#define DOOR_ACTUATOR_RELAY 5 //Pin used to toggle the door actuator relay
#define RELAY_ON 1            // GPIO value to write to turn on attached relay
#define RELAY_OFF 0           // GPIO value to write to turn off attached relay

#define TOGGLE_INTERVAL 1500  //Tells how many milliseconds the relay will be held closed
#define HEARTBEAT_INTERVAL 120000 //Number of miliseconds before the next heartbeat

#define CLOSED 0
#define OPEN 1
#define CLOSING 2
#define OPENING 3

#define OBSTR_MAX 20

const char *currentState[] = { 
                             "Closed", 
                             "Open", 
                             "Closing", 
                             "Opening" 
                             };

//Current state of the door
int cState;     

//Last state of the door
int lState;     

//The last full limit position of the door (open or closed)
int lLimit = 0; 

//Used for the error condition when the door is unexpectedly reversed
boolean obstruction = false;

int obstruction_count = 0;

// the timer object used for the heartbeat
SimpleTimer heartbeat;

MyMessage msgOpener(CHILD_ID_OPENER, V_STATUS);
MyMessage msgStatus(CHILD_ID_STATUS, V_TEXT);

/**
 * presentation - Present the garage door sensor
 */
void presentation() {
  
  sendSketchInfo( SKETCH_NAME, SKETCH_VERSION );
  
  // Register the garage door sensor with the gateway
  present( CHILD_ID_OPENER, S_BINARY );
  present( CHILD_ID_STATUS, S_INFO );
  
} //End presentation

/**
 * setup - Initialize the garage door sensor
 */
void setup() {

  // Set up the pins for reading the upper and lower limit sensors
  pinMode(UPPER_LIMIT_SENSOR, INPUT);
  pinMode(LOWER_LIMIT_SENSOR, INPUT);
  // Set up the pin to control the door opener
  pinMode(DOOR_ACTUATOR_RELAY, OUTPUT);

  Serial.println( SKETCH_NAME );

  // Set the heartbeat timer to send the current state at the set interval
  heartbeat.setInterval(HEARTBEAT_INTERVAL, sendCurrentState);
  
} //End setup

/**
 * loop - The main program loop
 */
void loop() {

  //Get the state of the door
  getState();

  //Here we check if the state has changed and update the gateway with the change.  We do this
  //after all processing of the state because we need to know if there was an obstruction
  if ((lState != cState) || obstruction == true) {
    sendCurrentState();

    obstruction_count ++;
    if (obstruction_count >= OBSTR_MAX) {
      //Once the obstruction is checked and sent, we can clear it
      obstruction = false;
    }

    //If the current state is full open or full closed we need to set the last limit
    if ( (cState == OPEN) || (cState == CLOSED) ) {
      setLastLimit( cState );
    }
  }

  //If the relay is on, shut it off
  if ( digitalRead( DOOR_ACTUATOR_RELAY ) == 1) {
    relayOff();                       
  }
  
  heartbeat.run();
  
} //End loop

/**
 * receive - Process the incoming messages and watch for an incoming boolean 1
 *           to toggle the garage door opener.
 */
void receive( const MyMessage &message ) {
  
  //We only expect one type of message from controller. But we better check anyway.
  if ( (message.type == V_STATUS) && (message.getBool() == RELAY_ON) ) {
    //Toggle the door opener
    toggleDoor();
  }
  
} //End receive

/**
 * sendCurrentState - Sends the current state back to the gateway
 */
void sendCurrentState() {
  
    send( msgStatus.set( obstruction == true ? "OBSTRUCTION" : currentState[cState] ) ); 
    
} //End sendCurrentState

/**
 * toggleDoor - Used to activate the garage door opener
 */
void toggleDoor() {

  digitalWrite( DOOR_ACTUATOR_RELAY, RELAY_ON );
  //Keep the relay on for the amount of time defined by TOGGLE_INTERVAL
  delay( TOGGLE_INTERVAL );
  
} //End toggleDoor

/**
 * relayOff - Used to turn off the door opener relay after the TOGGLE_INTERVAL
 */
void relayOff() {

  digitalWrite( DOOR_ACTUATOR_RELAY, RELAY_OFF );
  //Added this to tell the controller that we shut off the relay
  send( msgOpener.set(0) );
  
} //End relayOff

/**
 * getState - Used to get the current state of the garage door.  This will set the cState variable
 *            to either OPEN, CLOSED, OPENING and CLOSING
 */
void getState() {

  //read the upper sensor
  int upper = digitalRead( UPPER_LIMIT_SENSOR ); 
  //read the lower sensor
  int lower = digitalRead( LOWER_LIMIT_SENSOR ); 

  //Save the last state of the door for later tests
  lState = cState;

  //Check if the door is open
  if ((upper == HIGH) && (lower == LOW)) {
    //Set the current state to open
    cState = OPEN;
    //Check if the door is closed
  } else if ((upper == LOW) && (lower == HIGH)) {
    //Set the current state to closed
    cState = CLOSED;
    //Check if the door is in motion
  } else if ((upper == HIGH) && (lower == HIGH)) {
    //If in motion and the last full position of the door was open
    if (lLimit == OPEN) {
      //Set the current state to closing
      cState = CLOSING;
      //If in motion and the last full position of the door was closed
    } else {
      //Set the current state to opening
      cState = OPENING;
    }
  }
  
} //End getState

/**
 * setLastLimit - Checks the limit passed with the last limit (lLimit) and sets the last limit
 *                if there was a change.  It also checks the states against the limits and issues 
 *                an obstruction error if the limit and last limit
 *                
 * @param limit  integer limit - The limit to be checked
 */
void setLastLimit( int limit ) {
  
  //Here is where we check for our error condition
  if ( (lLimit == OPEN) && (limit == OPEN) && (lState == CLOSING) ) {
    //An obstruction has reversed the door.  No need to set the last limit because it already equals
    //the limit we are trying to set it to
    obstruction = true;
    //If we made it here and the last limit does not equal the limit we are setting then change it.  If
    //the last limit is equal to the limit we are setting then the last state was something other than
    //closing, so we don't need to do anything.
  } else if ( lLimit != limit ) {
    //Everything okay, set the last limit
    lLimit = limit;
    obstruction = false;
  }
  
} //End setLastLimit

[stevefury]

@dbemowsk hi, first off all, very nice job, i read your setup and i like what you did, but im not ready yet to master this c++ like you and i am trying to compile your sketch but i have some faults, with heartbeat interval, and maybe you can show me the way?

thanks

[stevefury]

@stevefury said in Automated garage door:

@dbemowsk hi, first off all, very nice job, i read your setup and i like what you did, but im not ready yet to master this c++ like you and i am trying to compile your sketch but i have some faults, with heartbeat interval, and maybe you can show me the way?

thanks

nobody???

[skywatch]

@stevefury said in Automated garage door:

... but i have some faults, with heartbeat interval,

Some faults? Ah well then, that's easy to fix!

nobody???

All the psychic team are on holiday, so you will have to help those who might be willing to help you. So.....

1. Post the code (in full) that you have problems with (use code tags </>).
2. Post the detailed messages for the errors you enounter.
3. Tell us exactly what is wrong and/or why you think it is wrong and what you are expecting.

[zboblamont]

@skywatch :sweat_smile: