Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

RF 433 Switch Failing

Thales Maia last edited by

Hi there, I equipped all my home lights with a RF 433 switch, like the one bellow.

I use a normal three-way switch and a remote (433) switch. To power them, I use a 12V 3A power source and a 33mF capacitor together with the power source.

The problem I'm facing is that from time to time (~5 - 12hrs), with no apparent reason, the relay switches. Since it always switch to original state, I've assumed that it was a power source failure problem. That is why I changed the power source and put a big capacitor. The problem remains.

Does anyone ever used this module? If so, can you tell me if this is reliable?
I needed to power the system of since it was turning my lights on while I was sleeping.

Important detail about my installation. I got lot of CAT5e cables, so I used them with a splitter to power up 12V to the boards.
Also, it seems that is always the same boards that fail.
Reply Quote 0
1 Reply Last reply

1
Posts

24
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Arduino Nano Every problem
Hardware • • hakha4

6

1
Votes

6
Posts

84
Views

I bought the Every because it implied it was backward compatible with the nano. No, it's not, as we found out. Be that as it may, any word on a getting the Every working with mySensors?
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

73
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3282
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

15
Views

No one has replied

RF 433 Switch Failing

Suggested Topics

Over the air updates
General Discussion • • ToSa

Arduino Nano Every problem
Hardware • • hakha4

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sleep mode for bmp280
Hardware • • fishermans

Sensors and more
Hardware • • Robert Leverett

1
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

RF 433 Switch Failing

Suggested Topics

Over the air updates General Discussion • • ToSa

Arduino Nano Every problem Hardware • • hakha4

Which one should i choose? PIR or microwave sensor Hardware • • h01

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sleep mode for bmp280 Hardware • • fishermans

Sensors and more Hardware • • Robert Leverett

1Online

11.4kUsers

11.1kTopics

112.7kPosts

Over the air updates
General Discussion • • ToSa

Arduino Nano Every problem
Hardware • • hakha4

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Sleep mode for bmp280
Hardware • • fishermans

Sensors and more
Hardware • • Robert Leverett

1
Online

11.4k
Users

11.1k
Topics

112.7k
Posts