Battery percentage - Help needed

[ericvdb]

Your 100 k ohm should be 1 M Ohm

And you swapped the resistors, R1 should be 1Mohm, R2 should be 470kohm.
And to stabilize the readings a bit, add a 0.1uF capacitor over R2

[ksga]

@ericvdb I replaced the resistors as suggested and added a capacitor (the smallest one I have a hand i 2.2uf - hope that's okay).
Now it shows 10% at full charge:

Serial started
Voltage: 3309 mV
//bla bla bla
T: 24.41
//more bla.
H: 44
//transmit bla bla bla
Battery voltage: 3300 mV
Battery percent: 10 %

Actual current on battery is 4.19V

[boozz]

Multiply batteryPcnt by 10

[ksga]

@boozz
Sounds like a plan :dancers:

But where do I do it?
Here, somewhere?

  if (batteryReportCounter >= BATTERY_REPORT_CYCLE) {
    long batteryVolt = readVcc();
    DEBUG_PRINT("Battery voltage: "); DEBUG_PRINT(batteryVolt); DEBUG_PRINTLN(" mV");
    uint8_t batteryPcnt = constrain(map(batteryVolt,VMIN,VMAX,0,100),0,255);   
    DEBUG_PRINT("Battery percent: "); DEBUG_PRINT(batteryPcnt); DEBUG_PRINTLN(" %");
    gw.sendBatteryLevel(batteryPcnt);
    batteryReportCounter = 0;
  }

[ksga]

Update..
Tried it like this:

  // Check battery
  if (batteryReportCounter >= BATTERY_REPORT_CYCLE) {
    long batteryVolt = readVcc();
    DEBUG_PRINT("Battery voltage: "); DEBUG_PRINT(batteryVolt); DEBUG_PRINTLN(" mV");
    uint8_t batteryPcnt = constrain(map(batteryVolt,VMIN,VMAX,0,100),0,255)*10;   
    DEBUG_PRINT("Battery percent: "); DEBUG_PRINT(batteryPcnt); DEBUG_PRINTLN(" %");
    gw.sendBatteryLevel(batteryPcnt);
    batteryReportCounter = 0;
  }

And got this result:

Battery voltage: 3300 mV
Battery percent: 100 %

So at least it seems to work :dancer:
Hoping voltage will drop like crazy through the night ;)

[sundberg84]

I like to collect 4 readings (every 15min) in an array and the take the average reading and send every hour. This way you will avoid getting readings going up and down and smoothen out the curve a bit.

[m26872]

Your setup with 470k and 100k would make a quite good divider ratio for that Li battery range. Maybe increase both a little to limit leakage current.

BUT you can NOT use the readVcc() function here since battery isn't connected to Vcc. Instead you should replace it the normal code used with the voltage divider and analogRead() function. Can't guide you, but it should be like the standard example sketch for battery monitoring. This will give you more info. http://forum.mysensors.org/topic/2210/battery-sensor-measure-for-li-ion-cells

[ksga]

@m26872 Thank you for the pointer.
I used the sketch from the link, but still the readings are quite far off.

I have tried checking the actual voltage at the division point. It reads 0.58V with a battery charge of 3.81V.
I my math doesn't fail me, it should be 0.69V...

I then looked at the actual resistance of R1 and R2.
R1=1012e3
R2=220e3

Of course this changes things, but not too drastically - now it should be 0.68V.
So I'm 15% wrong at my division point!

Any suggestions?

I should add that the serial output vary a bit at first, but then settles in after 30 seconds or so. I guess that could be because the capacitor is a bit on the large size...

[m26872]

@ksga You got the analogReference() and pinMode() in setup section? Post your sketch.

[ksga]

@m26872

#include <SPI.h>
#include <MySensor.h>  
#include <DHT.h>  

#define CHILD_ID_HUM 0
#define CHILD_ID_TEMP 1
#define HUMIDITY_SENSOR_DIGITAL_PIN 3

// define values for the battery measurement
#define R1 1012e3
#define R2 220e3
#define VMIN 3.2
#define VMAX 4.2
#define ADC_PRECISION 1023
#define VREF 1.1

MySensor gw;
DHT dht;
unsigned long SLEEP_TIME = 5000; // Sleep time between reads (in milliseconds)
float lastTemp;
float lastHum;
boolean metric = true; 
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
int oldBatteryPcnt = 0;
int BATTERY_SENSE_PIN = A0;


void setup()  
{ 
     // use the 1.1 V internal reference
 
     analogReference(INTERNAL);
 

  gw.begin();
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN); 

  // Send the Sketch Version Information to the Gateway
  gw.sendSketchInfo("Humidity", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  
  metric = gw.getConfig().isMetric;
}

void loop()      
{  
   int batteryPcnt = getBatteryPercentage();

   Serial.print("Battery percent: ");
   Serial.print(batteryPcnt);
   Serial.println(" %");

   if (oldBatteryPcnt != batteryPcnt) {
     // Power up radio after sleep
     gw.sendBatteryLevel(batteryPcnt);
     oldBatteryPcnt = batteryPcnt;
   }
  
  // totally random test values
  gw.send(msgTemp.set(20, 1));
  gw.send(msgHum.set(42, 1));

  gw.sleep(SLEEP_TIME); //sleep a bit
}

int getBatteryPercentage() {

  // read analog pin value
  int inputValue = analogRead(BATTERY_SENSE_PIN);
  
  // calculate the max possible value and therefore the range and steps
  float voltageDividerFactor = (R1 + R2) / R2;
  float maxValue = voltageDividerFactor * VREF;
  float voltsPerBit = maxValue / ADC_PRECISION;

  float batteryVoltage = voltsPerBit * inputValue;
  float batteryPercentage = ((batteryVoltage-VMIN)/(VMAX-VMIN))*100;
  //int batteryPercentage = map(batteryVoltage, 0, maxValue, 0, 100);

  return batteryPercentage;
}

[m26872]

@ksga Can't see any error in your sketch. Sure you can add pinMode(BATTERY_SENSE_PIN, INPUT) but doubt it will matter.

So if you disconnect your divider from A0, the voltage at that divider point will raise to the right value?

[ksga]

@m26872 I decided to trip everything from my breadboard and start over.
First thing - the voltage divider:
Simple Bat+ > pos.rail > R1 (1M, new specimen, verified resistance with multimeter) > R2(220k)/0.22uf capacitor > neg.rail > Bat-
In paralel I added an LED to put a bit of load on the battery for more realistic current.

The results are:
Battery current: 4.03V
Neg.rail to coupling point R1-R2: 0.61V
Coupling point R1-R2 to Pos.rail: 2.78V

Does that make any sense?
I would expect 0.61V+2.78V=4.03V (or maybe I still haven't grasped the concept.)

Hopefully this photo will make someone wiser than me point out my many mistakes ;-)

[m26872]

@ksga I can't see any current limiting resistor to the LED?
Start as simple as possible with few components. Short and few connections and wires to limit unexpected voltage drops in wires, breadboard or connections between. Remove the caps.

[ksga]

@m26872 Thank you for sticking with me.. I'm quite puzzled by this.
Removed all caps. Added a 1k resistor in front of the LED.
Checked resistance of wires - individually and mounted (all ~0.5 Ohm)

Readings remain the same:

Where does the last "0,63V" go - and should the fact that it is the same as the current over R2 teach me something?

[m26872]

@ksga When you used the word "current" instead of "voltage" twice makes me a little worried. I still believe in Kirchhoff and suggest your next move is to throw away the breadboard and leave just the battery and resistors wrap wired and then measure.

[ksga]

UPDATE:
So I decided to go ahead and connect the ProMini and nrf24l01+

Now the output from the terminal fluctuated between 80% and 105% with no real pattern.
So I added a 0.22uf across R2

Now the output is stable:

Battery percent: 104 %

I still only measure 0.63V across R2.
I guess the remaining error could be written down to the 1.1V reference being off. I think I read somewhere that it can be 10% off!

[stephenmhall]

here is the battery related code from my battery powered temp sensor. Took a while to get the battery correct. Before this thread I had not seen any other code correcting for battery max / min voltages. I am using the 3.7V li-ion cells which actually seem to top out at 4.2V. I cap the percent at 99 for Vera.

float fmap(float x, float in_min, float in_max, float out_min, float out_max) {
  return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
}

void loop()      
{  
  delay(dht.getMinimumSamplingPeriod());
  int sensorValue = analogRead(BATTERY_SENSE_PIN);

   // 1M, 330K divider across battery and using internal ADC ref of 1.1V
   // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
   // ((1e6+330e3)/330e3)*1.1 = Vmax = 4.43 Volts
   // 4.43/1023 = Volts per bit = 0.0043336591723688
   // 4.2 = 100% 2.5 = 0%

   float batteryV  = sensorValue * 0.004333659;
   float batteryVmap = fabs(fmap(batteryV, 2.5, 4.2, 0.0, 1000.0));
   int batteryPcnt = batteryVmap / 10;
   if(batteryPcnt >= 100){
    batteryPcnt = 99;

[gyro]

This post is deleted!