Can't get the void receive() to work, on Repeater and Node's

[delinend]

Hi.

I use the last 2.0.1-beta dev. version (from last night), and I can't get the function void receive(const MyMessage &message) to work.
It works fine on a Gateway setup.

Have tryed 2 types of setups.

1. Node(ID6) to a Repeater(ID7). I see the debug data on the repeater, but can't get any data via the void receive().
2. Node(ID6) to Node(ID7). Also here, I see the data on Node(ID7), but can't get any data via the void receive() funktion.

Any ideas?
Node(ID6) has a Static parent to Node-ID7, and Node(ID7) has a Static parent to Node-ID6

The void receive(const MyMessage &message) funktion, now works fine, from version 2.0.1-beta, on at GatewaySerial setup.

[AWI]

@delinend Can you post the sketch.

[delinend]

@AWI
Here the Node6, that sends temperatur, from a IR sensor to Parent-ID7

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_NODE_ID 6
//#define MY_DEFAULT_ERR_LED_PIN 4
#define MY_RF24_CHANNEL 123
#define MY_RF24_PA_LEVEL RF24_PA_HIGH

#define MY_PARENT_NODE_ID 7
#define MY_PARENT_NODE_IS_STATIC

//#define MY_REGISTRATION_FEATURE
#define MY_TRANSPORT_DONT_CARE_MODE

//#define MY_REPEATER_FEATURE

#include <SPI.h>
#include <MySensors.h>
#include <Wire.h>
#include <Adafruit_MLX90614.h>

Adafruit_MLX90614 mlx = Adafruit_MLX90614();

unsigned long SLEEP_TIME = 500; // Sleep time between reads (in milliseconds)

// Initialize temperature message
MyMessage msg(0,V_TEMP);

float temperature;



void setup()  
{ 
 mlx.begin();
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");
  present(0, S_TEMP);
}

void loop()     
{     

//  Serial.print("Ambient = "); Serial.print(mlx.readAmbientTempC()); 
//  Serial.print("*C\tObject = "); Serial.print(mlx.readObjectTempC()); Serial.println("*C");

 temperature = mlx.readObjectTempC();
 Serial.println(temperature,1);
      // Send in the new temperature
      send(msg.setSensor(0).set(temperature,1));

   
  
  sleep(SLEEP_TIME);
}

Ande here Node7, from where I can see the temperatur data, via MY_DEBUG, but not via the void receive() function,

// Enable debug prints to serial monitor
#define MY_DEBUG
//#define MY_SPECIAL_DEBUG
//#define MY_DEBUG_VERBOSE_SIGNING
//#define MY_DISABLED_SERIAL




// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#define MY_NODE_ID 7
//#define MY_DEFAULT_ERR_LED_PIN 4
#define MY_RF24_CHANNEL 123
#define MY_RF24_PA_LEVEL RF24_PA_HIGH


#define MY_PARENT_NODE_ID 6
#define MY_PARENT_NODE_IS_STATIC
#define MY_TRANSPORT_DONT_CARE_MODE

// Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level.
//#define MY_RF24_PA_LEVEL RF24_PA_LOW

// Enable serial gateway
//#define MY_GATEWAY_SERIAL
//#define MY_GATEWAY_W5100
//#define MY_REPEATER_FEATURE




#include <MySensors.h>




void setup() {
//  Serial.begin(19200);
//  Serial.begin(MY_BAUD_RATE);
  Serial.println("Started . Please wait...");
  // Setup locally attached sensors
}

void presentation() {
 // Present locally attached sensors
 //sendSketchInfo("Temperature Sensor", "1.1");
}

void loop() {
  // Send locally attached sensor data here
//Serial.println(tempp,1);
delay(10);

}

void receive(const MyMessage &message) {
//wait(10);
  Serial.println("received something: ");
//Serial.println(message.type);
  Serial.println(message.sender);
//  Serial.println(message.sensor);
//  Serial.println(message.getBool());

}

[AWI]

@delinend said:
send(msg.setSensor(0).set(temperature,1));

shouldn't that be

send(msg.setDestination(7).setSensor().set(temperature,1));

in order to have messages delivered at the right destination == 7

[delinend]

@AWI
You hare a Hero :-) That works!
Btw. Is the setting #define MY_TRANSPORT_DONT_CARE_MORE the right setting, when in a 2 Node's only setup ? I can't else get the Node6 beginning transmitting data.

[AWI]

@delinend The "royal way" is to have one node be a gateway. Else you need the "don't care"