Unable to register new node

[gersongarcia67]

Environment

Controller: MyController.org version 0.0.3.Alpha2
Gateway: MQTT
Mysensors version: 2.0.x
Number Nodes: 2
Radio Type: MY_RADIO_NRF24
Node CPU: Arduino Nano ATmega328

Issue

When I tried to add another node (any sensor type or no sensor at all) I am getting error, looks like the new node is not able to contact the gateway via radio. I enabled full debug and I am seeing the following messages:

TSM:INIT
RF24:write register, reg=0, value=14
RF24:write register, reg=3, value=3
RF24:write register, reg=4, value=95
RF24:write register, reg=5, value=76
RF24:write register, reg=6, value=39
RF24:read register, reg=6, value=39
RF24:read register, reg=5, value=76
RF24:write register, reg=16, value=115
RF24:write register, reg=29, value=6
RF24:write register, reg=2, value=2
RF24:write register, reg=1, value=0
RF24:write register, reg=28, value=3
RF24:flushRX
RF24:flushTX
RF24:write register, reg=7, value=112
TSM:RADIO:OK
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
RF24:write register, reg=0, value=12
RF24:power down

I replaced the CPU, the radio, I added 4.7uf capacitor, 2 other nodes communicated properly.

I need some help to understand the messages.

Thank you very much,

Gerson