Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Are there any RFM69 shields for Arduino pro mini?

Cliff Karlsson last edited by

Is there any shields/modules like the jModule wher you just add a pcb with a rfm69-radio to a pro mini?
Reply Quote 0
1 Reply Last reply
FotoFieber Hardware Contributor last edited by

I love this one:
https://www.openhardware.io/view/268/RFM69HW-interstitial-board-for-Pro-Mini-Temp-Humidity-sensor
Reply Quote 1
1 Reply Last reply

2
Posts

2004
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

5

1
Votes

5
Posts

70
Views

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
New user has questions
Hardware • • Doggie

7

0
Votes

7
Posts

50
Views

I am new in this forum and I have a question regarding mysensors and iobroker. I did not work with mysensors up to now. Since some weeks I use iobroker installed on a raspberrypi. Now I want to integrate my 433 Mhz doorbell in iobroker. I know, that there is an adapter for mysensors in iobroker. My question is: Is it possible to get a notification in iobroker if someone is pressing the button on my doorbell? As I understood, I have to connect the receiver to an arduino nano and connect the arduino to my rasberrypi on which iobroker is running.
hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

5

0
Votes

5
Posts

27
Views

@Tmaster Never assume the original PCB was just a circuit of components, the PCB can incorporate RF shields and antenna radio ground planes...
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

71
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.

Are there any RFM69 shields for Arduino pro mini?

Suggested Topics

Over the air updates
General Discussion • • ToSa

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

New user has questions
Hardware • • Doggie

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Which one should i choose? PIR or microwave sensor
Hardware • • h01

50
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

Are there any RFM69 shields for Arduino pro mini?

Suggested Topics

Over the air updates General Discussion • • ToSa

Best time of year to buy higher quality small project solar panels? Hardware • • NeverDie

New user has questions Hardware • • Doggie

hlk-pm01 are to noisy for rfm69? Hardware • • Tmaster

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Which one should i choose? PIR or microwave sensor Hardware • • h01

50Online

11.4kUsers

11.1kTopics

112.6kPosts

Over the air updates
General Discussion • • ToSa

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

New user has questions
Hardware • • Doggie

hlk-pm01 are to noisy for rfm69?
Hardware • • Tmaster

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

Which one should i choose? PIR or microwave sensor
Hardware • • h01

50
Online

11.4k
Users

11.1k
Topics

112.6k
Posts