3. Ethernet gateway and receive function

Ethernet gateway and receive function

  • DanieleF

    I have an ethernet gw based on Arduino Uno + W5100, working as expected.
    I tried to add an actuator (a simple relay), thus I added the usual "receive" function to the script, but at this point the ethernet stopped sending messages to others nodes.

    I tried filtering the destination, sensors type etc. but it still doesn't work.
    I suppose I should "forward" the messages manually in my receive function, correct?
    Does someone have a working example?

    Thanks
    Daniele

    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @danielef hard to say without looking at your code, but my guess is that you're doing something in receive that blocks normal processing.

    I am not sure if I have seen any sketches with actuators on the gateway, but it should be the same as other nodes.

    You should not forward messages manually.

    0
  • DanieleF

    The code is really basic, taken from the ethernet gw template simply adding the receive function:

    
#define MY_DEBUG

#define MY_GATEWAY_W5100

#define MY_RF24_CS_PIN 3
#define MY_RF24_IRQ_PIN 2
#define MY_RX_MESSAGE_BUFFER_FEATURE 6

#define MY_IP_ADDRESS 192,168,1,20
#define MY_IP_GATEWAY_ADDRESS 192,168,1,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0
#define MY_PORT 5003
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif
#include <Ethernet.h>

#define CHILD_ID_LIGHT 1

#include <MyRF24_P2_GW.h>
#include <MySensors.h>




void setup()
{

}

void presentation()
{

  present(CHILD_ID_LIGHT, S_BINARY, "P2 Luci Armadio");

}

void loop() {

  
}

void receive(const MyMessage &message)
{

  if (message.type == V_STATUS && message.sensor == CHILD_ID_LIGHT && !message.isAck()) {
    #ifdef MY_DEBUG
    Serial.println("*** Receiving ***");
    #endif
    statoLuci = message.getBool();
  }

}
    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @danielef thanks for sharing the code. It looks good. What does the debug output look like?

    0
  • DanieleF

    Sorry for the late response, I've been away for a few days.
    The debug output looks very odd to me:

    4850944 MCO:BGN-Q-,REL=255,VER=2.3.1
4850945 5,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 5,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850944 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MDO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 MCO:BGN:INIT GW,CP=RNNGA-Q-,REL=255,VER=2.3.1
4850945 ```
    0 mfalkvidd 1 Reply
  • mfalkvidd
    Mod

    @danielef the sketch you posted does not compile

    'statoLuci' was not declared in this scope

    are you sure this is the code you are using?
    Is there anything in MyRF24_P2_GW.h that we need to know about?

    From the log, it looks like the node is repeatedly calling Init, without reboot. That is very strange.

    0
  • DanieleF

    This is the full code, in my previous message I tried simplifing it and I missed a variable declaration:

    #define MY_DEBUG
//#define MY_DEBUG_DETAIL

#define MY_GATEWAY_W5100

#define MY_RF24_CS_PIN 3
#define MY_RF24_IRQ_PIN 2
#define MY_RX_MESSAGE_BUFFER_FEATURE 6

#define MY_IP_ADDRESS 192,168,1,20
#define MY_IP_GATEWAY_ADDRESS 192,168,1,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0
#define MY_PORT 5003
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

#if defined(MY_USE_UDP)
#include <EthernetUdp.h>
#endif
#include <Ethernet.h>

#define CHILD_ID_LIGHT 1

#include <MyRF24_P2_GW.h>
#include <MySensors.h>

MyMessage msgLIGHT(CHILD_ID_LIGHT, V_STATUS);


#define BUTTON_UP A4
#define BUTTON_DW A5

#include <Bounce2.h>
Bounce debounceUp = Bounce(); 
Bounce debounceDw = Bounce();

bool statoLuci = 1;
const byte numReed = 4;
const byte pinReed[numReed] = {A0,A1,A2,A3};
const byte pinRelay[numReed] = {5,6,7,8};
bool statoReed[numReed];



void setup()
{

//  request(CHILD_ID_LIGHT, V_STATUS);

  debounceUp.attach(BUTTON_UP, INPUT_PULLUP);
  debounceUp.interval(5);
  debounceDw.attach(BUTTON_DW, INPUT_PULLUP);
  debounceDw.interval(5);

  for (int i=0; i<numReed; i++){
    pinMode(pinReed[i], INPUT_PULLUP);
    statoReed[i] = 0;
    pinMode(pinRelay[i], OUTPUT);
  }

}

void presentation()
{

  present(CHILD_ID_LIGHT, S_BINARY, "P2 Luci Armadio");

}

void loop() {

  debounceUp.update();
  debounceDw.update();
  
  if ( debounceUp.fell() ) {
    Serial.println("UP");
  }
  if ( debounceDw.fell() ) {
    Serial.println("DOWN");
  }
  

  for (int i=0; i<numReed; i++){
    if (statoLuci){
      statoReed[i] = digitalRead(pinReed[i]);
      digitalWrite(pinRelay[i], statoReed[i]);
    }
    else
      digitalWrite(pinRelay[i], 0);

    #ifdef MY_DEBUG_DETAIL
    Serial.print("Reed ");
    Serial.print(i);
    Serial.print(" : ");
    Serial.println(statoReed[i]);
    #endif
  }

  #ifdef MY_DEBUG_DETAIL
  Serial.println("****************");
  wait(1000);
  #endif
  
}

/*
void receive(const MyMessage &message)
{

  if (message.destination == 0 && message.type == V_STATUS && message.sensor == CHILD_ID_LIGHT && !message.isAck()) {
    #ifdef MY_DEBUG
    Serial.println("*** Receiving ***");
    #endif
    statoLuci = message.getBool();
  }

}
*/

    MyRF24_2_GW.h contains simply some common defines I use for all the nodes connected to this GW:

    #define MY_RADIO_NRF24
#define MY_RF24_DATARATE   RF24_250KBPS
#define MY_RF24_CHANNEL 115

#ifndef MY_RF24_PA_LEVEL
#define MY_RF24_PA_LEVEL   RF24_PA_HIGH
#endif

#ifndef MY_PARENT_NODE_ID
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC
#endif
    0
Log in to reply
 

Suggested Topics

  • hek


    Announcements •  

    3
  • TheoL


    Troubleshooting •  

    6
  • kamilb85


    Troubleshooting •  

    2
  • Gibber


    Troubleshooting •  

    8
  • Gibber


    Troubleshooting •  

    1

13
Online

11.4k
Users

11.1k
Topics

112.7k
Posts



Copyright 2019 Sensnology   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service