works fine with 1.4.1 but not with 2.3.2

[Bmlsx]

hi all,

long time no see

have a strange issue that prbly is already answered somewhere but cannot find it

i have a very simple setup with only an arduino Pro mini and an NRF24 (the famous 1242AF) that works fine with mysensors 1.4.1 but with the latest version does not (!RF24:INIT:SANCHK FAIL) with the below debug output

any ideas ?

many thanx in advance

////////////// 1.4.1
sensor started, id 33
send: 33-33-0-0 s=255,c=0,t=17,pt=0,l=5,st=ok:1.4.1
send: 33-33-0-0 s=255,c=3,t=6,pt=1,l=1,st=ok:0
send: 33-33-0-0 s=255,c=3,t=11,pt=0,l=18,st=ok:Temperature Sensor
send: 33-33-0-0 s=255,c=3,t=12,pt=0,l=3,st=ok:1.0
NumSensors:
1
send: 33-33-0-0 s=0,c=0,t=6,pt=0,l=5,st=ok:1.4.1
send: 33-33-0-0 s=0,c=1,t=0,pt=7,l=5,st=ok:23.9

////////////////////////////2.3.2
16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=8,REL=255,VER=2.3.2
28 TSM:INIT
30 TSF:WUR:MS=0
32 RF24:INIT:PIN,CE=9,CS=10
36 RF24:SBY
36 RF24:WBR:REG=0,VAL=14
45 RF24:WBR:REG=3,VAL=3
47 RF24:WBR:REG=4,VAL=95
49 RF24:WBR:REG=5,VAL=76
53 RF24:WBR:REG=6,VAL=33
55 RF24:WBR:REG=29,VAL=4
57 RF24:RBR:REG=29,VAL=0
61 RF24:WBR:REG=16,VAL=115
63 RF24:WBR:REG=29,VAL=4
65 RF24:RBR:REG=6,VAL=0
69 !RF24:INIT:SANCHK FAIL
71 !TSM:INIT:TSP FAIL
73 TSM:FAIL:CNT=1
75 TSM:FAIL:DIS
77 TSF:TDI:TSL
77 RF24:SLP
79 RF24:WBR:REG=0,VAL=12

[mfalkvidd]

@Bmlsx could you post the entire sketches (for both 1.4.1 and 2.3.2)?

[Bmlsx]

hi,

I use the examples

from 1.4.1 the humidity sensor and from 2.3.2 the mock sensor

[Avamander]

@Bmlsx You're better off taking 2.x.x humidity sensors example. Alternatively, you should check if all the configuration options you're currently using are valid and used.

[Bmlsx]

hi again

had some progress

i found one sensebender micro board i had from the early days

and with the factory installed scketch I connected the NRF and it was working !!!

when i deployed an example from 2.3.2 again the same error

it must be something that changed over the years and now it is not compatible with my old RF24 HW

[Avamander]

@Bmlsx Check the configuration defines and/or just post the sketch.

[Bmlsx]

problem solved by throwing away 5 yo+ NRF24 and buying new ones

why 1.4.1 was working with those old NRFs remains a mystery

[mfalkvidd]

@Bmlsx mystery indeed. Thanks for reporting back.