Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

mysensors 8266 mqtt gate

Олег Веремеенко last edited by

I am very interested in your project. Please tell me in which version of arduino ide this project was compiled and the version of the Mysensors library that was used. I tried version 1.8.5 and 1.8.12 it gives a bunch of errors. Since the gateway is configured via the web interface, the already compiled file would do. Regards, Oleg.
Reply Quote 0
1 Reply Last reply

1
Posts

13
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
Sensors and more
Hardware • • Robert Leverett

1

0
Votes

1
Posts

15
Views

No one has replied
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

42
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

5

1
Votes

5
Posts

70
Views

It probably has to do with fewer people buying them once summer ends, so companies might lower prices to clear out stock before winter.
Which one should i choose? PIR or microwave sensor
Hardware • • h01

8

0
Votes

8
Posts

71
Views

Supposedly PIR doesn't work through glass (e.g. if looking for motion through a window), whereas I presume a microwave sensor might still work.
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }

mysensors 8266 mqtt gate

Suggested Topics

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

57
Online

11.4k
Users

11.1k
Topics

112.6k
Posts

mysensors 8266 mqtt gate

Suggested Topics

Over the air updates General Discussion • • ToSa

Sensors and more Hardware • • Robert Leverett

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design" Hardware • • wrendral

Best time of year to buy higher quality small project solar panels? Hardware • • NeverDie

Which one should i choose? PIR or microwave sensor Hardware • • h01

Does MySensors require Arduino Timer 2? Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

57Online

11.4kUsers

11.1kTopics

112.6kPosts

Over the air updates
General Discussion • • ToSa

Sensors and more
Hardware • • Robert Leverett

"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

Best time of year to buy higher quality small project solar panels?
Hardware • • NeverDie

Which one should i choose? PIR or microwave sensor
Hardware • • h01

Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

57
Online

11.4k
Users

11.1k
Topics

112.6k
Posts