SI7021 with Nodemanager

xlibor

Hi all, today i tested my SI7021 sensors and Nodemanager, but they not working very well.

After power on sensor, i receive presentation of two channels (temp and humidity), but then i receive only V_TEMP updates and never recived V_HUM, have anyone working sketch with nodemanager or can check my code, i start from template from nodemanager examples, i also checked sensor with my MCP2221 I2C<>USB converter and here it works.

/*
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2017 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*/

/**************************
Template

This sketch can be used as a template since containing the most relevant MySensors library configuration settings, 
NodeManager's settings, all its the supported sensors commented out and a sketch structure fully functional to operate with
NodeManager. Just uncomment the settings you need and the sensors you want to add and configure the sensors in before()
*/

/**********************************
 * MySensors node configuration
 */

// General settings
#define SKETCH_NAME "SI7021"
#define SKETCH_VERSION "1.0"
//#define MY_DEBUG
#define MY_NODE_ID 100

// NRF24 radio settings
#define MY_RADIO_RF24
//#define MY_RF24_ENABLE_ENCRYPTION
//#define MY_RF24_CHANNEL 125
//#define MY_RF24_PA_LEVEL RF24_PA_HIGH
//#define MY_DEBUG_VERBOSE_RF24
//#define MY_RF24_DATARATE RF24_250KBPS

// RFM69 radio settings
//#define MY_RADIO_RFM69
//#define MY_RFM69_FREQUENCY RFM69_433MHZ
//#define MY_IS_RFM69HW
//#define MY_RFM69_NEW_DRIVER
//#define MY_RFM69_ENABLE_ENCRYPTION
//#define MY_RFM69_NETWORKID 100
//#define MY_DEBUG_VERBOSE_RFM69
//#define MY_RF69_IRQ_PIN D1
//#define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN
//#define MY_RF69_SPI_CS D2
//#define MY_RFM69_ATC_MODE_DISABLED

// RFM95 radio settings
//#define MY_RADIO_RFM95
//#define MY_RFM95_FREQUENCY (RFM95_868MHZ)
//#define MY_DEBUG_VERBOSE_RFM95
//#define MY_RFM95_MAX_POWER_LEVEL_DBM (20)
//#define MY_RFM95_IRQ_PIN D1
//#define MY_RFM95_IRQ_NUM MY_RFM95_IRQ_PIN
//#define MY_RFM95_CS_PIN D8

// RS485 serial transport settings
//#define MY_RS485
//#define MY_RS485_BAUD_RATE 9600
//#define MY_RS485_DE_PIN 2
//#define MY_RS485_MAX_MESSAGE_LENGTH 40
//#define MY_RS485_HWSERIAL Serial1

// Message signing settings
//#define MY_SIGNING_SOFT
//#define MY_SIGNING_SOFT_RANDOMSEED_PIN 7
//#define MY_SIGNING_REQUEST_SIGNATURES
//#define MY_SIGNING_ATSHA204
//#define MY_SIGNING_ATSHA204_PIN 4
//#define MY_SIGNING_REQUEST_SIGNATURES

// OTA Firmware update settings
//#define MY_OTA_FIRMWARE_FEATURE
//#define OTA_WAIT_PERIOD 300
//#define FIRMWARE_MAX_REQUESTS 2
//#define MY_OTA_RETRY 2

// OTA debug output
//#define MY_DEBUG_OTA (0)
//#define MY_OTA_LOG_SENDER_FEATURE
//#define MY_OTA_LOG_RECEIVER_FEATURE
//#define MY_DEBUG_OTA_DISABLE_ACK

// Advanced settings
//#define MY_BAUD_RATE 9600
//#define MY_SMART_SLEEP_WAIT_DURATION_MS 500
#define MY_SPLASH_SCREEN_DISABLED
//#define MY_DISABLE_RAM_ROUTING_TABLE_FEATURE
//#define MY_SIGNAL_REPORT_ENABLED

// Optimizations when running on 2032 Coin Cell. Also set nodeManager.setSleepBetweenSend(500) and run the board at 1Mhz
#define MY_TRANSPORT_UPLINK_CHECK_DISABLED
//#define MY_TRANSPORT_WAIT_READY_MS  5000
//#define MY_SLEEP_TRANSPORT_RECONNECT_TIMEOUT_MS 2000
//#define MY_PARENT_NODE_ID 0
//#define MY_PARENT_NODE_IS_STATIC

/**********************************
 * MySensors gateway configuration
 */
 
// Common gateway settings
//#define MY_REPEATER_FEATURE

// Serial gateway settings
//#define MY_GATEWAY_SERIAL

// Ethernet gateway settings
//#define MY_GATEWAY_W5100

// ESP8266 gateway settings
//#define MY_GATEWAY_ESP8266
//#define MY_ESP8266_SSID ""
//#define MY_ESP8266_PASSWORD ""

// Gateway networking settings
//#define MY_IP_ADDRESS 192,168,178,87
//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
//#define MY_IP_SUBNET_ADDRESS 255,255,255,0
//#define MY_PORT 5003
//#define MY_GATEWAY_MAX_CLIENTS 2
//#define MY_USE_UDP

// Gateway MQTT settings
//#define MY_GATEWAY_MQTT_CLIENT
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
//#define MY_PORT 1883
//#define MY_MQTT_USER "username"
//#define MY_MQTT_PASSWORD "password"
//#define MY_MQTT_CLIENT_ID "mysensors-1"
//#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
//#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"

// Gateway inclusion mode
//#define MY_INCLUSION_MODE_FEATURE
//#define MY_INCLUSION_BUTTON_FEATURE
//#define MY_INCLUSION_MODE_DURATION 60
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Gateway Leds settings
//#define MY_DEFAULT_ERR_LED_PIN 4
//#define MY_DEFAULT_RX_LED_PIN  5
//#define MY_DEFAULT_TX_LED_PIN  6

/***********************************
 * NodeManager configuration
 */

#define NODEMANAGER_DEBUG OFF
#define NODEMANAGER_INTERRUPTS OFF
#define NODEMANAGER_SLEEP ON
#define NODEMANAGER_RECEIVE OFF
#define NODEMANAGER_DEBUG_VERBOSE OFF
#define NODEMANAGER_POWER_MANAGER OFF
#define NODEMANAGER_CONDITIONAL_REPORT OFF
#define NODEMANAGER_EEPROM OFF
#define NODEMANAGER_TIME OFF
#define NODEMANAGER_RTC OFF
#define NODEMANAGER_SD OFF
#define NODEMANAGER_HOOKING OFF
#define NODEMANAGER_OTA_CONFIGURATION OFF
#define NODEMANAGER_SERIAL_INPUT OFF

// import NodeManager library (a nodeManager object will be then made available)
#include <MySensors_NodeManager.h>

/***********************************
 * Add your sensors
 */

#include <sensors/SensorSI7021.h>
SensorSI7021 si7021;

/***********************************
 * Main Sketch
 */

// before
void before() {
	
  /***********************************
   * Configure your sensors
   */
  // EXAMPLES:
  // report measures of every attached sensors every 10 seconds
  nodeManager.setReportIntervalSeconds(10);
  // report measures of every attached sensors every 10 minutes
  //nodeManager.setReportIntervalMinutes(10);
  // set the node to sleep in 30 seconds cycles
  //nodeManager.setSleepSeconds(30);
  // set the node to sleep in 5 minutes cycles
  //nodeManager.setSleepMinutes(5);
  // report battery level every 10 minutes
  //battery.setReportIntervalMinutes(60);
  // set an offset to -1 to a thermistor sensor
  //thermistor.setOffset(-1);
  // change the id of a the first child of a sht21 sensor
  //sht21.children.get(1)->setChildId(5);
  // report only when the analog value is above 40%
  //analog.children.get(1)->setMinThreshold(40);
  // power all the nodes through dedicated pins
  //nodeManager.setPowerManager(power);

  // call NodeManager before routine
  nodeManager.before();
}

// presentation
void presentation() {
  // call NodeManager presentation routine
  nodeManager.presentation();
}

// setup
void setup() {
  // call NodeManager setup routine
  nodeManager.setup();
}

// loop
void loop() {
  // call NodeManager loop routine
  nodeManager.loop();
}

#if NODEMANAGER_RECEIVE == ON
// receive
void receive(const MyMessage &message) {
  // call NodeManager receive routine
  nodeManager.receive(message);
}
#endif

#if NODEMANAGER_TIME == ON
// receiveTime
void receiveTime(unsigned long ts) {
  // call NodeManager receiveTime routine
  nodeManager.receiveTime(ts);
}
#endif

at compilig i got two warnings:

In file included from C:\Users\Libor\Documents\Arduino\libraries\NodeManager-master/MySensors_NodeManager.h:87:0,
                 from C:\Users\Libor\Documents\Arduino\projects\NodeManager_test\NodeManager_test.ino:176:
C:\Users\Libor\Documents\Arduino\libraries\NodeManager-master/nodemanager/Sensor.cpp: In member function 'void Sensor::presentation()':
C:\Users\Libor\Documents\Arduino\libraries\NodeManager-master/nodemanager/Sensor.cpp:135:54: warning: invalid conversion from 'uint8_t {aka unsigned char}' to 'mysensors_sensor_t' [-fpermissive]
   present(child->getChildId(), child->getPresentation(), child->getDescription(), nodeManager.getAck());
                                ~~~~~~~~~~~~~~~~~~~~~~^~
In file included from C:\Users\Libor\Documents\Arduino\libraries\MySensors/MySensors.h:433:0,
                 from C:\Users\Libor\Documents\Arduino\libraries\NodeManager-master/MySensors_NodeManager.h:43,
                 from C:\Users\Libor\Documents\Arduino\projects\NodeManager_test\NodeManager_test.ino:176:
C:\Users\Libor\Documents\Arduino\libraries\MySensors/core/MySensorsCore.cpp:375:6: note:   initializing argument 2 of 'bool present(uint8_t, mysensors_sensor_t, const char*, bool)'
 bool present(const uint8_t childSensorId, const mysensors_sensor_t sensorType,
      ^~~~~~~

xlibor

I changed to development version of Nodemanager this remove compilation errors and then found that recomended library from Sparkfun not work. Then i edited header file SensorSI7021.h to work with Adafruit library and it works
my SensorSI7021.h:

/*
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2017 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
* 2021 modified by Libor Kozak to work with Adafruit library: https://github.com/adafruit/Adafruit_Si7021
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*/
#ifndef SensorSI7021_h
#define SensorSI7021_h

/*
SensorSI7021: temperature and humidity sensor
*/

#include <Wire.h>
//#include <SI7021.h>
#include <Adafruit_Si7021.h>

class SensorSI7021: public Sensor {
protected:
	Adafruit_Si7021* _si7021;//SI7021* _si7021;
	
public:
	SensorSI7021(uint8_t child_id = 0): Sensor(-1) {
		_name = "SI7021";
		children.allocateBlocks(2);
		new Child(this,FLOAT,nodeManager.getAvailableChildId(child_id),S_TEMP,V_TEMP,_name);
		new Child(this,FLOAT,child_id > 0 ? nodeManager.getAvailableChildId(child_id+1) : nodeManager.getAvailableChildId(child_id),S_HUM,V_HUM,_name);
	};
	
	// define what to do during setup
	void onSetup() {
		_si7021 = new Adafruit_Si7021();
		_si7021->begin();
	};

	// define what to do during loop
	void onLoop(Child* child) {
		// temperature sensor
		if (child->getType() == V_TEMP) {
			// read the temperature
			float temperature = _si7021->readTemperature();
			// convert it
			//temperature = nodeManager.celsiusToFahrenheit(temperature);
			// store the value
			child->setValue(temperature);
		}
		// Humidity Sensor
		else if (child->getType() == V_HUM) {
			// read humidity
			float humidity = _si7021->readHumidity();
			// store the value
			child->setValue(humidity);
		}
	};
};
#endif

SI7021 with Nodemanager

Suggested Topics

Sensors db
My Project • • Dvbit

Nrf5x on NodeManager
NodeManager • • nullos

DS18B20 ESP32 nodemanager problem
NodeManager • temperature ds18b20 esp32 node manager • • A3V

Compilation error
NodeManager • • htaxil

What could be the possible reasons for MySensors sensors not working with MyController on Raspberry Pi, and how can one troubleshoot and resolve the issue?
NodeManager • • Greg Bowers

Motion sensor node to always report not tripped state to reset controller value
NodeManager • • nero01

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

SI7021 with Nodemanager

Suggested Topics

Sensors db My Project • • Dvbit

Nrf5x on NodeManager NodeManager • • nullos

DS18B20 ESP32 nodemanager problem NodeManager • temperature ds18b20 esp32 node manager • • A3V

Compilation error NodeManager • • htaxil

What could be the possible reasons for MySensors sensors not working with MyController on Raspberry Pi, and how can one troubleshoot and resolve the issue? NodeManager • • Greg Bowers

Motion sensor node to always report not tripped state to reset controller value NodeManager • • nero01

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Sensors db
My Project • • Dvbit

Nrf5x on NodeManager
NodeManager • • nullos

DS18B20 ESP32 nodemanager problem
NodeManager • temperature ds18b20 esp32 node manager • • A3V

Compilation error
NodeManager • • htaxil

What could be the possible reasons for MySensors sensors not working with MyController on Raspberry Pi, and how can one troubleshoot and resolve the issue?
NodeManager • • Greg Bowers

Motion sensor node to always report not tripped state to reset controller value
NodeManager • • nero01

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts