Node inclusion problem.

[mfalkvidd]

@pw44 enter them into the search box at the top right at https://www.mysensors.org/apidocs/index.html to get the documentation. If things still are unclear, ask any wuestions you might have here.

[pw44]

@mfalkvidd ok, i did, and did not understand how it works, that's why i asked.

[mfalkvidd]

@pw44 the public documentation is the best way we know to describe them. If we knew a better way, we would update the public documentation.

Could you help us by describing what parts you understand and what parts you don't understand?

[pw44]

@mfalkvidd well, neither my build gateway or the two working nodes have MY_NODE_ID and MY_PARENT_NODE_ID.

in one of the posts, one user claimed not being able to include a node, but was able to do it by defining those https://forum.mysensors.org/post/36819.

so, the question is if those are necessary by having the gateway and nodes, and how to use it?

shall i define MY_NODE_ID 0 to the gateway and AUTO do the nodes, by MY_PARENT_NODE_ID, or MY_PARENT_NODE_ID 0 to the nodes?

yes, maybe stupid questions, but i didn't realize, as i have one gateway and two nodes working and a third one not being registered, even with some nrf24l01 replaced.

[mfalkvidd]

@pw44 as described in the documentation, Node id defaults to AUTO (tries to fetch id from controller).

So if you don’t specify MY_NODE_ID, the node will try to fetch an id from the controller.

[pw44]

@mfalkvidd ok, but does it have any influence by node being recognized by gateway?

[mfalkvidd]

@pw44 hard to tell without the logs from the node and the gateway from the same time

[mfalkvidd]

@pw44 I checked the startup sequence, and TSM:FPAR happens before TSM:ID. So no, setting MY_NODE_ID on your node would not have any effect in your case.

[pw44]

This is what i have from GW:

⸮⸮⸮⸮⸮hlD⸮x⸮hT⸮76 MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
134 TSF:LRT:OK
149 TSM:INIT
163 TSF:WUR:MS=0
186 TSM:INIT:TSP OK
207 TSM:INIT:GW MODE
229 TSM:READY:ID=0,PAR=0,DIS=0
262 MCO:REG:NOT NEEDED
scandone
1367 GWT:TIN:CONNECTING...
2396 GWT:TIN:CONNECTING...
scandone
state: 0 -> 2 (b0)
4175 GWT:TIN:CONNECTING...
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 5
cnt 

connected with Hirschberg, channel 1
dhcp client start...
ip:192.168.80.9,mask:255.255.255.0,gw:192.168.80.1
4393 GWT:TIN:IP: 192.168.80.9
4424 MCO:BGN:STP
4442 MCO:BGN:INIT OK,TSP=1
4471 TSM:READY:NWD REQ
4498 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
12252 GWT:TSA:C=0,CONNECTED
pm open,type:2 0
22390 GWT:RFC:C=0,MSG=0;255;3;0;2;
32460 GWT:RFC:C=0,MSG=0;255;3;0;2;
42660 GWT:RFC:C=0,MSG=0;255;3;0;2;
52698 GWT:RFC:C=0,MSG=0;255;3;0;2;
62829 GWT:RFC:C=0,MSG=0;255;3;0;2;
72967 GWT:RFC:C=0,MSG=0;255;3;0;2;
83002 GWT:RFC:C=0,MSG=0;255;3;0;2;
93141 GWT:RFC:C=0,MSG=0;255;3;0;2;
103175 GWT:RFC:C=0,MSG=0;255;3;0;2;

no node being recognized

and these are the arduino mini pro gpios being used

#define BUTTON_PIN1  3                                // Arduino Digital I/O pin for button/reed switch
#define BUTTON_PIN2  4                                // Arduino Digital I/O pin for button/reed switch
#define BUTTON_PIN3  5                                // Arduino Digital I/O pin for button/reed switch
#define BUTTON_PIN4  6                                // Arduino Digital I/O pin for button/reed switch
#define BUTTON_PIN5  7                                // Arduino Digital I/O pin for button/reed switch
#define BUTTON_PIN6  8                                 // Arduino Digital I/O pin for button/reed switch

[pw44]

@mfalkvidd may this problem be related with eeprom stored vars?

i will clear the eeproms and flash gatewayand nodes again.