SCT-013-030 current monitor sensor

[fredok]

.... u must to look the monitor for see "Envoi des données .... clamp=0" and after (a few minutes after) "Envoi des données .... clamp=1"
Look after ur domotic soft for see if your gw become something.

bye.

[warmaniac]

@fredok

nice ! thank you very much for fast solution :) I try it at home , it compiles well :+1:

[gohan]

@warmaniac you got errors because you need to move the
"#include <MySensors.h>" after all the "#DEFINE....." otherwise the library does not know how to be configured

[warmaniac]

@fredok

I modyfied your sketch (deleting unwanted code like dallas and light sensor) it works but i think I done something wrong, because it spams my gateway , now it looks like this

//#include <Arduino.h>
#define MY_DEBUG
#define MY_RADIO_NRF24
// EmonLibrary examples openenergymonitor.org, Licence GNU GPL V3  ***/
#include <SPI.h>
#include <MySensors.h>
#include <OneWire.h>
#include "EmonLib.h"             // Include Emon Library
EnergyMonitor emon1;             // Create an instance

#define CHILD_ID_CLAMP1 0
#define PIN_ANALOG_I1 A1 //pince amperemetrique1

bool receivedConfig = false;
bool metric = true; //truc v2.0

//int compat = 0;
unsigned long lastSend_temp = millis();
unsigned long lastSend_power = millis();
unsigned long lastSend_c;
unsigned long SEND_FREQUENCY = 120000; // Minimum time between send (in milliseconds). We don't wnat to spam the gateway.
unsigned long SEND_FREQUENCY_C = SEND_FREQUENCY / 30;
int index = 0;
double Irms1 = 0;
boolean pcReceived1 = false;

float nrj1 = 0, old_nrj1;

MyMessage IrmsMsg1(CHILD_ID_CLAMP1, V_WATT);
MyMessage kWhMsg1(CHILD_ID_CLAMP1, V_KWH);
MyMessage pcMsg1(CHILD_ID_CLAMP1, V_VAR1);

void presentation()
{

  sendSketchInfo("Multisensors_Entree", "2.0");  // Send the sketch version information to the gateway and Controller
  present(CHILD_ID_CLAMP1, S_POWER);   // Register this device as power sensor
  request(CHILD_ID_CLAMP1, V_VAR1);
}


void receive(const MyMessage &message)
{
  if (message.type == V_VAR1)
  {
    nrj1 = old_nrj1 = message.getFloat();
    Serial.print("Received last nrj count from gw:");
    Serial.println(nrj1);
    pcReceived1 = true;
  }

}

void setup()
{
  emon1.current(PIN_ANALOG_I1, 30.0);       // Current: input pin, calibration.
  Serial.println("SETUP completed");
}

void envoi_donnees(double intrms, int id_clamp)
{
  Serial.print("Envoi des donnees .... clamp="); Serial.println(id_clamp);
  double energie = (intrms * 232.0 * SEND_FREQUENCY / 1000) / 3.6E6;
  switch (id_clamp)
  {
    case 1:
      {
        send(IrmsMsg1.set(intrms * 232.0, 1));
        nrj1 += energie;
        send(kWhMsg1.set(nrj1, 5));
        send(pcMsg1.set(nrj1, 5));
        old_nrj1 = nrj1;
      }
      break;
  }
}

void loop() {
  unsigned long now = millis();
  bool sendTime_c = now - lastSend_c > SEND_FREQUENCY_C;
  // Calcul de Irms1 et Irms2
  if (sendTime_c) //calcul Irms moy clamp1/clamp2
  {
    if (index == 0)
    {
      Irms1 = emon1.calcIrms(1480);
    }
    else  
    {
      Irms1 = (index * Irms1 + emon1.calcIrms(1480)) / (index + 1);
    }
    lastSend_c = now;
    index++;
  }

bool sendTime_power = now - lastSend_power > SEND_FREQUENCY;

 if (sendTime_power)
{

  // Envoi ou request Puissance1
  if (pcReceived1) envoi_donnees(Irms1, 1);
  else     {
    request(CHILD_ID_CLAMP1, V_VAR1);
    Serial.println("Request VAR1");
  }

  }
}

and I get this results now

[fredok]

hello, i see the sketch send everyloop ???
try this

#define MY_DEBUG
#define MY_RADIO_NRF24
// EmonLibrary examples openenergymonitor.org, Licence GNU GPL V3  ***/
#include <SPI.h>
#include <MySensors.h>
#include "EmonLib.h"             // Include Emon Library
EnergyMonitor emon1;             // Create an instance

#define CHILD_ID_CLAMP1 0
#define PIN_ANALOG_I1 A2 //pince amperemetrique1

unsigned long lastSend_power = millis();
unsigned long lastSend_c = millis();
unsigned long SEND_FREQUENCY = 120000; // Minimum time between send (in milliseconds). We don't wnat to spam the gateway.
unsigned long SEND_FREQUENCY_C = SEND_FREQUENCY / 30;
int index = 0;
double Irms1 = 0;
boolean pcReceived1 = false;
float nrj1 = 0, old_nrj1;

MyMessage IrmsMsg1(CHILD_ID_CLAMP1, V_WATT);
MyMessage kWhMsg1(CHILD_ID_CLAMP1, V_KWH);
MyMessage pcMsg1(CHILD_ID_CLAMP1, V_VAR1);

void before() {

}


void presentation()
{
  sendSketchInfo("Multisensors_Entree", "2.0");  // Send the sketch version information to the gateway and Controller
  present(CHILD_ID_CLAMP1, S_POWER);   // Register this device as power sensor
  request(CHILD_ID_CLAMP1, V_VAR1);
}


void receive(const MyMessage &message)
{
  if (message.type == V_VAR1)
  {
    nrj1 = old_nrj1 = message.getFloat();
    Serial.print("Received last nrj count from gw:");
    Serial.println(nrj1);
    pcReceived1 = true;
  }
}

void setup()
{
  emon1.current(PIN_ANALOG_I1, 30.0);       // Current: input pin, calibration.
  Serial.println("SETUP completed");
}

void envoi_donnees(double intrms, int id_clamp)
{
  Serial.print("Envoi des donnees .... clamp="); Serial.println(id_clamp);
  double energie = (intrms * 232.0 * SEND_FREQUENCY / 1000) / 3.6E6;
  switch (id_clamp) //can be modified ...
  {
    case 1:
      {
        send(IrmsMsg1.set(intrms * 232.0, 1));
        nrj1 += energie;
        send(kWhMsg1.set(nrj1, 5));
        send(pcMsg1.set(nrj1, 5));
        old_nrj1 = nrj1;
      }
      break;
  }
}

void loop() {
  unsigned long now = millis();
  bool sendTime_c = now - lastSend_c > SEND_FREQUENCY_C;
  // Calcul de Irms1 et Irms2
  if (sendTime_c) //calcul Irms moy clamp1/clamp2
  {
    if (index == 0)
    {
      Irms1 = emon1.calcIrms(1480);
    }
    else  
    {
      Irms1 = (index * Irms1 + emon1.calcIrms(1480)) / (index + 1);
    }
    lastSend_c = now;
    index++;
  }

bool sendTime_power = now - lastSend_power > SEND_FREQUENCY;

 if (sendTime_power)
{

  // Envoi ou request Puissance1
  if (pcReceived1) envoi_donnees(Irms1, 1);
  else     {
    request(CHILD_ID_CLAMP1, V_VAR1);
    Serial.println("Request VAR1");
  }
  //on reinitialise les compteurs
  lastSend_power = now;
  index = 0;
  }
}

if problem copy the screen of monitor.thx

[fredok]

ahoj, if not working i will try with a new arduino for test the code.
dobrý večer

[warmaniac]

@fredok

sketch works better now , not spamming

but I dont understand current values

[fredok]

its seem good kWh every 2min
1864W is the power value

send(IrmsMsg1.set(intrms * 232.0, 1));

the sketch send power value P (in W) and energy (in kWh) calculated over 2min.

double energie = (intrms * 232.0 * SEND_FREQUENCY / 1000) / 3.6E6;

// and after
nrj1 += energie;
send(kWhMsg1.set(nrj1, 5));

in domoticz i have one "dispositif" included instant power Watt and day cumulate energy kWh
bye

[warmaniac]

@fredok

Thank you very much! Only one question left, with multimeter I measured my voltage 241.0 V could I update it in sketch or ?

[fredok]

a clamp measure only intensity I (in A) and Power =UrmsxIrms so if in u home Urms=241V u can change with this value but the power measurment not consider cosphy
by example the power measurment of my fridge =257W but true value is (with cosphy) 257x0,56=....W
so if u change 232V with 241V why not but at the end its will continu to be a approximate of the true power.
bye

[warmaniac]

@fredok

Okay :) understand now, and what about calibration for wiring I followig this site

https://learn.openenergymonitor.org/electricity-monitoring/ct-sensors/how-to-build-an-arduino-energy-monitor-measuring-current-only?redirected=true

And they calibrate

 emon1.current(1, 111.1); 

And yours calibration

  emon1.current(PIN_ANALOG_I1, 30.0);

Is some difference after this calibrations in measuring ?

[gohan]

They also have the same sensor with also voltage measurement for a more accurate reading

[warmaniac]

@gohan

Because with test sketch from that site I get actual consumption 0,5 kWh but from mysensors sketch I get much higher values look

1,7 kWh per one hour is too much , I had only TV and fridge in power on mode, I had total consumption per last year about 2140 kWh , which is about 6 kWh per day.

[fredok]

hello,

1. the constant 30 is the divide between ratio/burden resistor including inside the clamp
   for me ration=1800 and R=62ohm (1800/62 approx 30)
   http://www.planete-domotique.com/notices/S/C/SCT013-030V.pdf
2. i can see 1677 Wh=1,677 kWh ... but 1900W for only TV+fridge its many
   mine clamp2 log in domoticz
   
3. Maybe it can help u??? i have a pulse powercounter count every flash (1 Wh of energy) of mine electric box and the power (Watt) send to gw is wrong in domoticz but the energy counting (kWh) is great.
   
   Where come the wrong of fake power (GW ? sketch ? domoticz , i dont know)
   bye

[warmaniac]

@fredok

I had SCT-013-000 , not SCT-013-030 maybe this is the problem of measuring .

[warmaniac]

updated my sketch with new values for SCT-013-00 result is now

#define MY_DEBUG
#define MY_RADIO_NRF24
// EmonLibrary examples openenergymonitor.org, Licence GNU GPL V3  ***/
#include <SPI.h>
#include <MySensors.h>
#include "EmonLib.h"             // Include Emon Library
EnergyMonitor emon1;             // Create an instance

#define CHILD_ID_CLAMP1 0
#define PIN_ANALOG_I1 A1 //pince amperemetrique1

unsigned long lastSend_power = millis();
unsigned long lastSend_c = millis();
unsigned long SEND_FREQUENCY = 120000; // Minimum time between send (in milliseconds). We don't wnat to spam the gateway.
unsigned long SEND_FREQUENCY_C = SEND_FREQUENCY / 30;
int index = 0;
double Irms1 = 0;
boolean pcReceived1 = false;
float nrj1 = 0, old_nrj1;

MyMessage IrmsMsg1(CHILD_ID_CLAMP1, V_WATT);
MyMessage kWhMsg1(CHILD_ID_CLAMP1, V_KWH);
MyMessage pcMsg1(CHILD_ID_CLAMP1, V_VAR1);

void before() {

}


void presentation()
{
  sendSketchInfo("Multisensors_Entree", "2.0");  // Send the sketch version information to the gateway and Controller
  present(CHILD_ID_CLAMP1, S_POWER);   // Register this device as power sensor
  request(CHILD_ID_CLAMP1, V_VAR1);
}


void receive(const MyMessage &message)
{
  if (message.type == V_VAR1)
  {
    nrj1 = old_nrj1 = message.getFloat();
    Serial.print("Received last nrj count from gw:");
    Serial.println(nrj1);
    pcReceived1 = true;
  }
}

void setup()
{
  emon1.current(PIN_ANALOG_I1, 111.1);       // Current: input pin, calibration.
  Serial.println("SETUP completed");
}

void envoi_donnees(double intrms, int id_clamp)
{
  Serial.print("Envoi des donnees .... clamp="); Serial.println(id_clamp);
  double energie = (intrms * 240.0 * SEND_FREQUENCY / 1000) / 3.6E6;
  switch (id_clamp) //can be modified ...
  {
    case 1:
      {
        send(IrmsMsg1.set(intrms * 240.0, 1));
        nrj1 += energie;
        send(kWhMsg1.set(nrj1, 5));
        send(pcMsg1.set(nrj1, 5));
        old_nrj1 = nrj1;
      }
      break;
  }
}

void loop() {
  unsigned long now = millis();
  bool sendTime_c = now - lastSend_c > SEND_FREQUENCY_C;
  // Calcul de Irms1 et Irms2
  if (sendTime_c) //calcul Irms moy clamp1/clamp2
  {
    if (index == 0)
    {
      Irms1 = emon1.calcIrms(1480);
    }
    else  
    {
      Irms1 = (index * Irms1 + emon1.calcIrms(1480)) / (index + 1);
    }
    lastSend_c = now;
    index++;
  }

bool sendTime_power = now - lastSend_power > SEND_FREQUENCY;

 if (sendTime_power)
{
  // Envoi ou request Puissance1
  if (pcReceived1) envoi_donnees(Irms1, 1);
  else     {
    request(CHILD_ID_CLAMP1, V_VAR1);
    Serial.println("Request VAR1");
  }
  //on reinitialise les compteurs
  lastSend_power = now;
  index = 0;
  }
}

[fredok]

great !!!!!

[brahim]

Hi , i update your sketch for Multiple sensor

#define MY_RADIO_NRF24
#define MY_DEBUG

#include <SPI.h>
#include <MySensors.h>  
#include <EmonLib.h> 

#define SERIAL_BAUD 115200

#define PIN_ANALOG_I1 A0   // The input you attached SCT1.
#define PIN_ANALOG_I2 A1   // The input you attached SCT2.
#define PIN_ANALOG_I3 A2   // The input you attached SCT3.

#define CHILD_ID_WATT 0    // child-id of sensor
#define CHILD_ID_KWH  1    // child-id of sensor
#define CHILD_ID_VAR1 2    // child-id of sensor

#define MAX_CT 3           // Number of CT sensor

EnergyMonitor ct1, ct2, ct3;

MyMessage msgWatt(CHILD_ID_WATT,V_WATT);
MyMessage msgKwh(CHILD_ID_KWH,V_KWH);
MyMessage msgVar(CHILD_ID_VAR1,V_VAR1);

unsigned long lastSend_power = millis();
unsigned long lastSend_c = millis();
unsigned long SEND_FREQUENCY   = 60000;               // 1 mn Minimum time between send (in milliseconds).
unsigned long FREQUENCY_SAMPLE = SEND_FREQUENCY / 12 ; // ( 5 s)

#define MAX_CT 3

double  Irms[MAX_CT];
float   nrj[MAX_CT];
boolean pcReceived[MAX_CT];

int    index = 0;

void setup()
{
#ifdef MY_DEBUG
  Serial.begin(SERIAL_BAUD);
  Serial.println("Begin SETUP");
#endif
  //ct1.current(PIN_ANALOG_I1, 111.1);     // Current: input pin, calibration.                                        
  ct1.current(PIN_ANALOG_I1, 60);          // current constant = (100 ÷ 0.050) ÷ 33 Homs = 60
  ct2.current(PIN_ANALOG_I2, 60);            
  ct3.current(PIN_ANALOG_I3, 60);            

  Irms[0] = ct1.calcIrms(1480);            // initial boot to charge up capacitor (no reading is taken) - testing
  Irms[1] = ct2.calcIrms(1480);
  Irms[2] = ct3.calcIrms(1480);

  for (int i=0; i<MAX_CT; i++) {
       Irms[i] = nrj[i] = 0;
       pcReceived[i]=false;
  }
#ifdef MY_DEBUG
  Serial.println("SETUP completed");
#endif

}

void presentation() {
  
  sendSketchInfo("Energy Meter", "2.1");

  present(0, S_POWER);
  request(0, V_VAR1);
  
  present(1, S_POWER);
  request(1, V_VAR1);

  present(2, S_POWER);
  request(2, V_VAR1);  
}


void receive(const MyMessage &message) {
  int SensorID ;

  SensorID = message.sensor ;
  
  if (message.type == V_VAR1) {
    
      nrj[SensorID] =  message.getFloat();
      pcReceived[SensorID] = true;

#ifdef MY_DEBUG
      Serial.print("Received last nrj[");
      Serial.print(SensorID);
      Serial.print("] count from GW:");
      Serial.println(nrj[SensorID]);
#endif
  }
}

void send_data(double intrms, int SensorID) {

#ifdef MY_DEBUG
  Serial.print("Send data for SensorID="); 
  Serial.println(SensorID);
#endif

  double energie = (intrms * 240.0 * SEND_FREQUENCY / 1000) / 3.6E6;
  
  nrj[SensorID] += energie;
  send(msgWatt.setSensor(SensorID).set(intrms * 240.0, 1));
  send(msgKwh.setSensor(SensorID).set(nrj[SensorID], 5));
  send(msgVar.setSensor(SensorID).set(nrj[SensorID], 5));
}

void loop() {
  
  unsigned long now = millis();
  double _Irms[MAX_CT];
  bool sendTime_c = now - lastSend_c > FREQUENCY_SAMPLE;
  
  if (sendTime_c)
  {
    _Irms[0] = ct1.calcIrms(1480) ; if (_Irms[0] < 0.3) _Irms[0] = 0;
    _Irms[1] = ct2.calcIrms(1480) ; if (_Irms[1] < 0.3) _Irms[1] = 0;
    _Irms[2] = ct3.calcIrms(1480) ; if (_Irms[2] < 0.3) _Irms[2] = 0;

    Irms[0] = (index * Irms[0] + _Irms[0]) / (index + 1);
    Irms[1] = (index * Irms[1] + _Irms[1]) / (index + 1);
    Irms[2] = (index * Irms[2] + _Irms[2]) / (index + 1);

    lastSend_c = now;
    index++;

#ifdef MY_DEBUG
    for (int i=0; i<MAX_CT; i++) {
        Serial.print("CT");
        Serial.print(i);  Serial.print(" : ");
        Serial.print(Irms[i]*240.0);  // Apparent power
        Serial.print(" ");
        Serial.println(Irms[i]);      // Irms
    }
#endif
  }

  bool sendTime_power = now - lastSend_power > SEND_FREQUENCY;

  if (sendTime_power)
  {
    for (int i=0; i<MAX_CT; i++) {
    // Envoi ou request Puissance1
       if (pcReceived[i])
        { 
         send_data(Irms[i], i);
        } else {
         request(i, V_VAR1);
         Serial.println("Request VAR1");
        }
    }
    //on reinitialise les compteurs
    lastSend_power = now;
    index = 0;
  }
}

[fredok]

fine thx....